ELECTRONIC SCALE WB-1 QQMANVB-11OMA REMOTE DISPLAY VERSION C D INSTRUCTION MANUAL , . . . .
4. RS-232C CommunicationSpecifications .......................................... 12 Specifications ....................................................................................... 12 B Names. and connection methods for signal lines .................. 12 Weighing Mode .................................................................................. 12 4 BM1 Mode ............................................................................................. 12 5 . ~ ~ ~ ~ ...........................
- This equipment has been calibrated as a precision weighing instrument and can be used to certify weights and/or business transactions. *It can be used to obtain reference data during medical examinations, such as periodic checkups, and can help the prevention of obesity.
The circuit board,incorporates a fuse (100m4, 125V) for electronic equipment. If devices other than the original AC adapter are used or a large electrical current is applied, the fuse will be blown for safety purposes. If the fuse is blown, the unit must be inspected and repaired. As the fuse forms a fixed part of the unit and cannot be easily disassembled by the customer, please consult your nearest Tanita sales office or agent when the fuse needs to be replaced. A [Maintenance] . ..
Product Components Please verify that the following components are in the package. I Accessories I .
H Control Panel I.&, STABILIZED STEP ON HEIGHT BM1 BM1 MODE " . . ..-- m W1 , , j Power on and / or reset the display to zero. NET mark: Power off. STABILIZED mark: An arrow 4 appears next to this icon when the tare weighing function is on. Indicates that the displayed figure has stabilized. STEP ON mark (Ready mark): Indicates that the scale is ready to begin measurements. HEIGHT mark (Unit of height): BM1 mode, and/ or height setting. !.
B! Level Adjustment 7 / For accurate measurement, place the unit on as flat a surface as possible and adjust the level with the adjustable feet so the bubble in the level gauge is in the center of the frame. I X l I I level surface. *Adjust the he~ghtby rotatmg the adjustable feet If the equipment is not stable, --for example because not all-the feet are on a levei suriace, there is q risk that it will topple over and it will be impossible to obtain an accurate measurement.
H Prepare Power Source aWhen using the AC Adapter Insert the cable plug for the AC Adapter into the DC jack on the side of the Display Box, and insert the AC Adapter plug into a 230V AC mains DC jack. Then confirm the Pilot Lamp on the AC Adapter lights up. -1 *To avoid electric shocks, do not insert and remove the plug with wet ' 3 C jack hands. -Pilot Lamp *Use only the AC adapter (MODEL: A30930G) specified. Using an AC Adapter other than that specified may cause malfunctions.
~~~~~ 1. Standard Weighing Procedures \ \ * l kN TE JWHT 4 4 1 l STEP ON 4 1. Turn on the power by pressing the key, -/ 2. After all the segments flash, B.Okg is displayed. 00c1.n * * 3. Step onto the center of the scale platform. The weight reading will be displayed. 4. Measurement i s completed. When the person being weighed steps off the scale, the display will return to [O.Okg]. Turn off the power by pressing the Bkey. 2.Tare Weighing 1. Turn on the power by pressing the key. 2.
4.BMI Calculation: 1. Turn on the power by pressing the key. 2. A h r aii the segmenis iiash, [D-Okg] is dispiayed. . 3. Push .~ . . .. for within two seconds. [O.Okg] and the default height [170cm] will be displayed. LOCK t mm 4. Set your height with +he key. (This can also be entered after you step on the scale). Stand still on the scale platform. The weight will be displayed. 5. Once your height and weigh+have been established, press The weight and B M figure will be displayed.
specifications HNames and connection methods for signal lines Terminal no. 1 2 3 4 5 EIA RS-232C Asynchronous method 2,400 baud 7 bit -EVEN 1bit Communication standard Communicationmethod Signal speed Data bit length Parity Stop bit Signalname 1 TXD RXD GND 9 6 6- An RS-232C connector (D sub 9 pin female) is attached to the side of the display box. When connecting the display box with a persohal computer, e.tc., please use an RS-232C straight cable. Use the RS232C cable ahorter than 3m long. A .
B! Possible Problems If problems occur, please refer to the following instructions. If the problem persists contact your nearest Tanita sales or repair center. Problem Solution The unit does not turn on when the key is pressed. @WhenUsing with t h e - ~ ~ ~ d a ~ t e r Ensure that the AC Adapter cable is properly connected with the Display Unit. Ensure that the AC Adapter is correctiy inserted in the mains DC jack. @Usingdry cell batteries The batteries may have run out.
Specifications TYPE W-1OOhL4 WB-11OhL4 AC adaptercentre minus1MODEL A30930GCLASS 2 Input Voltage : 230VACSOHz65mA Output Voltage : 9VDC*0.45VDC Power Source Rated Current : 300mA No Load Input Voltage : 12VDC*0.6VDC LR6 (AA Alkaline battery) X 6, (Not included) Power Consumption I 0.3W max . . - Measurement System . - . .. _ -. Strain Gauge Load Cell Weight Measurement Maxmum Capacity/Minrnum Graduation 200kgl0. lkg 270kg/0. Ikg Accuracy at f ~ scribration t *O.lkg .- . .. . .-.-..
