SCF TC STEREO CHORUS/FLANGER & Pitch Modulator USER’S GUIDE
CONTENTS Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SCF Sound Quality . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Front Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 The Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Examples of Settings . .
INTRODUCTION Thank you for purchasing the TC Chorus/Flanger/Pitch Modulation pedal. TC Electronic has developed this product to the highest standards ensuring top sound quality with no noise or distortion added to your audio signal. The "full" spatial effects and the lack of noise has made the TC SCF pedal a favorite choice of many professional musicians both on the road and in the studio.
INTRODUCTION Pitch Modulation: A combination of chorus and pitch - vibrato which creates a "light" chorus sound. Real Stereo When using stereo the effect signals and the clean signal appear simultaneously in both sides. The effect signals are alternating phase reversed in left and right sides, creating a unique spatial dimension. Excellent dynamic range The 100dB signal to noise ratio means that there is very little background noise generated by the electronics.
8 SCF SOUND QUALITY PROFESSIONAL SIGNAL LEVELS One of the key elements to obtaining professional sound quality is proper impedance at the in and output(s). If an effect pedal should be able to pick up the full bandwidth from your instrument, it is very important that it does not "load" your instrument, i.e. it must have a high input impedance. To prevent loss through cables, effect loops or loading by the amp input, the outputs must have drive capability, i.e. the out impedance has to be very low.
FRONT DESCRIPTION 1 SPEED Controls the Rate of sweep in a range from 1 sweep every 10 seconds to 10 sweeps each second (0,1-10 Hz). 2 INTENSITY The INTENSITY potentiometer has 3 functions - one for each mode: - - In the CHORUS mode it blends between chorus and clean signal. In FLANGER mode it controls the strength of the Comb filter phasing of the signal (like feedback on a delay). In PITCH MODULATION mode it is blend control, mixing chorus and vibrato.
FRONT DESCRIPTION GETTING STARTED 9 OUTPUT (STEREO) Outputs the right channel of the stereo effects signal. Connect the input source (instrument, pick-up or high output microphone) by a mono jack cord to the Input jack. 10 BYPASS Switches the audio signal into or around the effects circuitry. 11 EX. BYPASS By connecting a simple momentary switch here, the bypass function can be remote controlled.
THE CONTROLS There are four sound controls on the SCF: INPUT GAIN, SPEED, WIDTH and INTENSITY Setting Input Gain: Using the TC SCF with an instrument… When used with a guitar, bass or keyboard with normal output volume and an amplifier with normal input volume the INPUT GAIN should be turned fully counter clockwise. (The signal will then have an unchanged level). Or…using the TC SCF with a mixing console. The AUX/EXT.
THE CONTROLS If you want "out of pitch" sounds for special effects, both SPEED and WIDTH can be turned into the last third of their range. Adjusting INTENSITY This has 3 different functions depending on the mode setting… In the CHORUS mode INTENSITY is a control for the "notching" depth of the chorus effect. Turning the control clock-wise increases the "notching" which is well suited for non distorted single and rhythm guitars as well as most keyboards.
EXAMPLES OF SETTINGS NAME 18 SPEED INTENSITY MODE TECHNICAL SPECIFICATIONS WIDTH CHORUS I 1 4 CHORUS 3 CHORUS II 2 5/6 CHORUS 5 CHORUS III 5 2 CHORUS 5 FLANGER I 2 3 FLANGER 5 FLANGER II METALLIC 2 2 FLANGER 2 FLANGER CLASSIC 4 4 FLANGER 1 FLANGER .5 3.5 FLANGER MAX PITCH MOD. .5 5 P.M. Dynamic Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100dB Frequency response . . . . . . . . . . . . . . . . . . . . . . . . . .20-20kHz Input impedance .
TROUBLESHOOTING In case you encounter any difficulties, please go thru this troubleshooting before calling the service center ERROR ERROR CHECK Distortion INPUT GAIN adjusted too high - 0dB max should be put in - install an input attenuator if necessary - try another signal source - try another cable does the OVERLOAD LED light? Chorus Effect Do not mix the two outputs together disappears these are in anti-phase. To make a mono-compatible effect, CHECK No "on" LED - click the bypass footswitch.
TROUBLESHOOTING INTENSITY at or near maximum. This set-up will produce a chorus effect, which is almost as "broad" and is mono-compatible however the chorus effect will be at one side only. 3) Use another TC product called the TC 1210 Spatial Expander & Stereo Chorus/Flanger, which has two linkable chorus units for full stereo/mono compability as well as other exciting effects. NOTES Please read and follow these instructions before connecting this unit.
NOTES This equipment has been tested and found to comply with the limits for a Class B Digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
NOTES Do not attempt servicing of this unit yourself. Always refer to qualified personal. Do not use this unit near water; for example, near a bath tub, washbowl, kitchen sink, laundry tub, in wet basement or near a swimming pool ect. This unit should only be connected to correct power supply outlet, please refer to the technical specifications. For the customers in Canada: This Class B Digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
