Owner's Manual
4
Keep the unit in standby while setting it up (
E
on page5).
1 Cushions are attached to the tonearm
for use during transportation. Remove
them in the directions of the arrows.
A
N
T
I
–
S
K
A
T
I
N
G
3
0
A
N
T
I
–
S
K
A
T
I
N
G
3
0
A
N
T
I
–
S
K
A
T
I
N
G
3
0
Cushion for
transportation
Cushion for
transportation
2 Place the unit on a at surface.
Place it on a flat surface so that the record can be accurately
traced.
3 Install the platter.
Align the platter with the center shaft and install it.
o Place the large side of the hole down.
Center shaft
Platter
4 Loop the belt around the motor pulley.
Loop the included flat belt around the outside of the
platter, and then loop the belt around the motor pulley.
o Be careful not to let the rubber become twisted.
o Rotate the platter several times to make sure that the
flat belt is secure.
Motor pulley
Flat belt
5 Install the pulley cover.
Align the small cutout in the pulley cover with the small
protuberance on the pulley, as shown in the illustration
below.
o If these are not aligned, the pulley cover will slant.
Pulley cover
6 Place the felt mat on the platter.
Place the included felt mat on the platter before using it.
7 Install the counterweight.
Place the counterweight over the end of the tonearm,
and press it gently as you turn it right to attach it.
o When the counterweight can be moved toward the
bearing, installation is complete.
A
N
T
I
–
S
K
A
T
I
N
G
3
0
A
N
T
I
–
S
K
A
T
I
N
G
3
0
Counterweight
Bearing
8 Install the headshell.
Insert the headshell on the end of the tonearm and turn
the nut to secure it in place.
Headshell
Nut
Balancing the tonearm and adjusting
the tracking force
A
N
T
I
–
S
K
A
T
I
N
G
3
0
A
N
T
I
–
S
K
A
T
I
N
G
3
0
Anti-skating dial
Tonearm lifter lever
Counterweight
Tracking force adjustment ring
Center line
1 Set the anti-skating dial to zero.
Preparing the record player
2 Move the tonearm clasp to the right to
release the tonearm.
Clasp
A
N
T
I
–
S
K
A
T
I
N
G
3
0
A
N
T
I
–
S
K
A
T
I
N
G
3
0
3 Raise the tonearm lifter lever and shift
the tonearm to the left slightly.
4 Lower the tonearm lifter lever.
5 Turn the counterweight and adjust so
that the tonearm is level.
A
N
T
I
–
S
K
A
T
I
N
G
3
0
A
N
T
I
–
S
K
A
T
I
N
G
3
0
o Remove the protective cap from the cartridge stylus
before adjusting.
o Be careful not to let the cartridge stylus touch the
unit.
6 Return the tonearm to its original posi-
tion, and use the clasp to lock it.
7 Turn the tracking force adjustment ring
so that the center line aligns with 0 on
the scale.
A
N
T
I
–
S
K
A
T
I
N
G
3
0
A
N
T
I
–
S
K
A
T
I
N
G
3
0
o Only turn the ring. Be careful not to let the counter-
weight turn.