Owner's Manual
Table Of Contents
- ENGLISH
- FRANÇAIS
- INSTRUCTIONS DE SÉCURITÉ IMPORTANTES
- Marques déposées et copyrights
- Avant l’utilisation
- Branchements
- Nomenclature et fonctions des parties
- Préparation de la platine
- Couvercle anti-poussière
- Manipulation des disques
- Fonctionnement de base
- Changement de cellule
- Notes sur les pointes pour disque
- Écoute avec des enceintes Bluetooth®
- Guide de dépannage
- Caractéristiques techniques
- ESPAÑOL
- INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- Marcas y derechos
- Antes de su utilización
- Conexiones
- Nombres y funciones de las partes
- Preparación del reproductor de discos de vinilo
- Tapa
- Manejo de los discos de vinilo
- Funcionamiento básico
- Cambio de la cápsula
- Notas sobre las agujas para discos
- Escuchar con altavoces Bluetooth®
- Solución de problemas
- Especificaciones
- DEUTSCH
- WICHTIGE SICHERHEITSHINWEISE
- Warenzeichen und Urheberrechte
- Vor der ersten Inbetriebnahme
- Anschlüsse
- Bedienelemente und deren Funktion
- Vorbereiten des Plattenspielers
- Die Staubschutzhaube
- Der Umgang mit Schallplatten
- Grundlegende Bedienung
- Wechseln des Tonabnehmersystems
- Tonabnehmernadeln
- Wiedergabe über Bluetooth®-Lautsprecher
- Hilfe bei Funktionsstörungen
- Technische Daten
- ITALIANO
- IMPORTANTI ISTRUZIONI PER LA SICUREZZA
- Marchi e diritti d’autore
- Prima dell’uso
- Collegamenti
- Nomi e funzioni delle parti
- Preparazione del giradischi
- Coperchio antipolvere
- Maneggiare i dischi
- Operazioni di base
- Sostituzione della cartuccia
- Note sugli stili
- Ascolto con altoparlanti Bluetooth®
- Risoluzione dei problemi
- Specifiche
- NEDERLANDS
- BELANGRIJKE VEILIGHEIDSINSTRUCTIES
- Handelsmerken en auteursrechten
- Vóór gebruik
- Aansluitingen
- Namen en functies van onderdelen
- De draaitafel voorbereiden
- Stofkap
- Omgaan met grammofoonplaten
- Basisbediening
- Het element verwisselen
- Opmerking over draaitafelnaalden
- Via Bluetooth®-luidsprekers luisteren
- Problemen oplossen
- Specificaties
- SVENSKA
- 日本語
- 保証とアフターサービス (よくお読みください)
- WARRANTY/GARANTIE/GARANTÍA/GARANTIE/GARANZIA/GARANTIE/GARANTI
ENGLISHENGLISH
Preparing the record player
Attaching the dust cover
Hinge
Main unit
Dust cover
1 Insert the hinges completely into the
hinge holders at the left and right ends
of the back of the main unit.
2 Align the tops of the hinges with the
dust cover hinge holders and insert
them.
o Close the dust cover during playback. Doing so
prevents stylus skipping caused by unintended con-
tact and protects the stylus tip from outside sound
pressure.
o Do not open or close it when a record is playing.
Doing so could, for example, cause the stylus to skip.
o Keep it closed whenever possible to keep dust out.
Removing the dust cover
Hold both edges of the dust cover and lift it slowly to remove it
along with the hinges from the unit. Then, remove the hinges
from the dust cover.
Dust cover
Opening and closing the dust cover
Open
Opening
Hold the front edge of the dust cover and gently lift it open
completely until it stops.
The dust cover will stay open in this position.
Closing
Gently lower the dust cover until it is closed.
V
Be careful not to pinch your fingers, for
example, when opening and closing the
dust cover.
Handling records
Holding records
When holding a record or removing it from its sleeve, avoid
touching the grooves by holding the record by its label and edge
with one hand or by holding it by its edge with both hands.
Label Grooves
Outer edge
Cleaning
o Fingerprints and dust on a record can cause noise and the
sound to skip, as well as damage the record itself and the
stylus. Use a commercially available record cleaner to clean
records. Do not use thinner or anything other than a record
cleaner. Such chemicals could harm the surface of the record.
o When using a record cleaner, wipe the surface of the record
in a circular motion, following the grooves.
Precautions
o Do not leave records in places that are exposed to direct
sunlight or are very hot or very humid. Leaving a record in
such a condition for a long time could result in warping,
mold growth or other damage.
o Do not stack multiple records or place heavy objects on top
of them. Do not leave records at an angle for long amounts of
time, either. Doing so could result in warping or other damage.
o Do not allow hard objects to directly touch the audio
grooves. Doing so could cause scratches.
o After you finish playing a record, always put it back into
its sleeve for storage. Leaving a record unprotected could
result in warping or scratching.
o Do not use cracked records.
9 Adjust the anti-skating dial.
As an approximation, set it to the same value as the track-
ing force. Then, while playing a record (see page8),
adjust the position so that the left and right volumes are
balanced.
The example in the illustration below shows a tracking
force setting of 3.5g.
ATTENTION
Depending on the condition of a record, the left-right
volume balance could become uneven and skipping
could occur.
In such cases, try making the following adjustments.
If the sound jumps backward (stylus skips backward)
Slightly lower the anti-skating dial setting.
If the sound jumps forward (stylus skips forward)
Slightly increase the anti-skating dial setting.
7