User's Manual
Table Of Contents
- 1 Introduction
- 2 Block Diagram
- 3 Application Interface
- 3.1 Power Supply
- 3.2 Power-up / -down Slew-Rate
- 3.3 Reset
- 3.4 Supply Voltage Monitor
- 3.5 Serial Interface
- 3.6 GPIO Interface
- 3.7 I2C Interface0F
- 3.8 SPI Serial Peripheral Interface1F
- 1.1
- 3.9 Bluetooth Radio Interface
- 3.10 WLAN Coexistence Interface2F
- 3.11 Slow Clock Interface
- 3.12 Test Mode Enable
- 3.13 Pin Strapped System Memory Boot Mode Invocation
- 3.14 Operating in a Power-Switched Environment
- 3.15 Serial Wire Interface
- 4 Module Pins
- 5 Electrical Characteristics
- 6 Mechanical Characteristics
- 1
- 7 Application Diagram
- 8 Approvals/Certifications
- 9 Related Documents
- 10 Packing
- 11 Ordering Information
BlueMod+SR/AI
BlueMod+SR/AP
Hardware Reference
Release r04d01 www.stollmann.de Page 39 of 65
5.7.3 BLE Receiver
VSUP = 2,5V to 3,6V, T
amb
= +20°C
Measured conducted according to BT specification RF-PHY.TS/4.0.1
Receiver
Frequ
/GHz
Min Typ Max
BT
Spec
Unit
Sensitivity at 30,8% PER
2,402
-87
-83
≤ -70 dBm
2,440
-90
-86
2,480
-90 -86
Reported PER during PER
report integrity test 2,426 50 50 65,4
50
< PER
< 65,4
%
Maximum received signal at 30,8% PER
-10 0 ≥ -10 dBm
Continuous power required to
block Bluetooth reception at -
67dBm with 0,1%PER
0,030 - 2,000
-30
> 0
-30
dBm
2,000 - 2,400
-35
0
-35
2,500 -3,000
-35
0
-35
3,000 . 12,75
-30
>0
-30
C/I co-channel
8
21
≤21
dB
Adjacent channel
Selectivity C/I
F = F
0
+ 1 MHz
1 15 ≤15 dB
F = F
0
- 1 MHz
-9 15 ≤15 dB
F = F
0
+ 2 MHz
-27
-17
≤-17
dB
F = F
0
- 2 MHz
-19
-15
≤-15
dB
F = F
0
+ 3 MHz
-43
-27
≤-27
dB
F = F
0
- 5 MHz
-49
-27
≤-27
dB
F = F
image
-24
-9
≤-9
dB
Maximum level of intermodulation interferers
-50 -18 ≥-50 dBm
VSUP = 2,5V to 3,6V, T
amb
= -30°C
Measured conducted according to BT specification RF-PHY.TS/4.0.1
Receiver
Frequ
/GHz
Min Typ Max
BT
Spec
Unit
Sensitivity at 30,8% PER
2,402
-87
-83
≤ . 70 dBm
2,440
-90
-87
2,480
-90 -87
Reported PER during PER
report integrity test 2,426 50 50 65,4
50
< PER
< 65,4
%
Maximum received signal at 30,8% PER
-10 0 ≥ -10 dBm
VSUP = 2,5V to 3,6V, T
amb
= +85°C
Measured conducted according to BT specification RF-PHY.TS/4.0.1
Receiver
Frequ
/GHz
Min Typ Max
BT
Spec
Unit
Sensitivity at 30,8% PER
2,402
-87
-83
≤ . 70 dBm
2,440
-89 -85
2,480
-89 -85
Reported PER during PER
report integrity test 2,426 50 50 65,4
50
< PER
< 65,4
%
Maximum received signal at 30,8% PER
-10 0 ≥ -10 dBm
Table 18: RF Performance BLE Receiver