Specification Sheet
2 / 19
APPLICATION
- Side exhaust option to preserve precious kitchen storage space
or if ducting is more convenient for this conguration*
- A slim 2' rectangular duct is available to place exible blower in
areas such as unused corner in island or peninsula applications
- Blower must be accessible for maintenance
- Elbow and ductwork are not included
FLEXIBLE BLOWER INSTALLATION – SIDE EXHAUST WITH SLIM 2' RECTANGULAR DUCT EXAMPLE
UCVM36RS
36-INCH DOWNDRAFT VENTILATION
MASTERPIECE
®
SERIES
REQUIRED BLOWER
VTD600P –
600 CFM
600 CFM exible
blower can be
installed as an
integrated or
inline blower
10
3
/
8
"
(264 mm)
12
3
/
4
"
(324 mm)
12
3
/
4
"
(324 mm)
7
3
/
8
"
(187 mm)
11
5
/
8
"
(295 mm)
5
1
/
4
"
(133 mm)
5
1
/
8
"
(130 mm)
11
5
/
8
"
(295 mm)
5"
(127 mm)
measurements in inches (mm)
10
3
/
8
"
(264 mm)
12
3
/
4
"
(324 mm)
12
3
/
4
"
(324 mm)
7
3
/
8
"
(187 mm)
11
5
/
8
"
(295 mm)
5
1
/
4
"
(133 mm)
5
1
/
8
"
(130 mm)
11
5
/
8
"
(295 mm)
5"
(127 mm)
measurements in inches (mm)
OPTIONAL ACCESSORIES
EXTNCE5
This cable extends 5 ft. to move the electrical
panel out of the way to offer full installation
exibility in any ducting scenario while
installing the downdraft. Ability to connect
two cables together to make a 10 ft. cable.
REPLACEMENT CHARCOAL FILTER
UCVFILTER
Includes 1 replacement charcoal lter for
UCVRECIRC recirculation kit
DOWNDRAFT GAS COOKTOP SEAL
TRIM KIT UCV36ST
Includes trim, seal, metal grill, and fasteners.
Required for installations with 36" gas
cooktops.
RECIRCULATION
KIT UCVRECIRC
Includes 1 charcoal
lter and 1 metal
grill vent plate
(blower sold
separately). Use with
induction/electric
cooktops only
REQUIRED ACCESSORIES
CVTSIDE8
8" round transition to connect
CVDUCT2 to VTD600P. Use with
VTD600P blower as an inline instal-
lation, and ducting with 8" round
duct connections.
CVTRECT2
Transition required to connect
CVDUCT2 rectangular duct
to downdraft housing at left,
right, or rear
CVDUCT2
Rectangular 2 ft. long x 1 7/8 in
deep x 19 in wide duct. CVDUCT2
transition required to directly
connect CVDUCT2 to sides or rear
of downdraft housing. Can be
used as an extension to exhaust
through a cabinet or wall, and can
be cut to modify length. For use
with installation of inline or remote
blower applications with CVTSIDE6,
CVTSIDE8, and CVTSIDE10.
* For only front downward ducting applications, electrical panel must be remotely mounted. Electrical panel
can still be remotely mounted in other exhaust configurations if desired. Optional 5' extension cable EXTNCE5
accessory is available to connect remotely placed electrical panel to downdraft. Refer to installation manual.
NOTE: Some applications may require deeper cabinets. Refer to installation manual.
Page 11 of 12