Signature Series Control +Steamhead Installation Manual For Tutorials and Troubleshooting visit www.thermasol.com/solutions SET-NTS-XX Traditional, SEM-NTS-XX Modern, SEMR-NTS-XX Modern Recessed. SEC-NTS-XX Contemporary, SER-NTS-XX Regency.
1 STEAM SELECT 2 1 STEAM 2 Installation Manual For Tutorials and Troubleshooting visit www.thermasol.
Signature Series Control Installation Instructions 1 Important Information before You Install The Signature Series Control must be installed inside the shower. The Signature Series control will only function on the current SSM, SSA and PRO Series generators. The control should be installed 60" from the floor of the shower and away from the steamhead.
Signature Series Control Installation Instructions 2 Tools and Materials Controller (Contemporary style shown here) Silicone Materials needed: ❏ Signature Series control ❏ CAN-Bus Cable (included with generator) ❏ Silicone ❏ Other materials as required Parts enclosed Mud Ring (RIK-SEMR-1) for SEMR-NTS-XX installation only Installation instructions, warranty, static cling warning label Tools needed: ❏ 1/2” drill for surface mount ❏ Follow pre-installation instruction on page 5 for recessed mount contr
Signature Series Control Installation Instructions 4 Control Installation and Data Cable Connection Back of Control Route the data cable (included with generator) through the finished wall to the back side of the control. The other end of the cable runs to the steam generator location or if present to SWM-2 or PDM. NOTE: It is recommended to run the cable through electrical conduit. Connector Detail DO NOT pinch, nail, staple, wedge, or bind the data cable.
Signature Series Control Installation Instructions 5 Mud Ring Installation + Sealing Control For Recessed Controls Only (SEMR-XX and SEMR-NTS-XX) Silicone (included) Recessed Control (shown) Data Cable Step 1: BEFORE TILE - Use the supplied mud ring by attaching to wall face using a few standard screws. Then tile to the edge of the mud ring. Step 2: Once finished tile is completed remove mud ring from wall. Ensure that the total minimum depth is 5/8” so control face sits flush to wall.
Signature Series Control Installation Instructions 6 Operation For More Operating Interactive Instructions please visit: www.thermasol.com/solutions A Taking a Steam Bath On your ThermaSol Signature Series Control, touch and release the power icon to power on. To turn off the steam unit touch and release the power icon once. B Setting or Changing the Temperature Set Point Press the or button until you reach the temperature menu. Press button.
7 Trouble Shooting and Error Codes Visit www.thermasol.com/solutions. Click on Troubleshoot then click on Signature Series Control Error Codes Read warnings on page 3. For illustrative purposes only. Consult with qualified professional for steam room construction details. PN: 97005_NC 4/16 8 THERMASOL.COM I 800.776.
Steamhead Installation Installation Manual For Tutorials and Troubleshooting visit www.thermasol.
Steamhead Installation Instructions 2 Tools and Materials Parts enclosed Steamhead (Contemporary style shown here) Silicone Installation instructions 3 Steamhead Location Materials needed: ❏ Steamhead ❏ Steamhead Rough-In Housing 1/2" Copper Tubing (For PRO-650, PRO-850 3/4" drop elbow, 3/4" Copper Tubing 50' max.
Steamhead Installation Instructions 4 Steamhead Installation A A When finalizing installation, install the steamhead into the housing, making sure that the aromatherapy fill channels are facing upwards. B To ensure that no moisture gets behind the steamhead and into the wall, place a generous bead of waterproof silicone around the steamhead, using the machined groove (located on the back of the steamhead) as a guide.
1958 STEAM WAY ROUND ROCK, TX 78665 PHONE: 800.776.0711 | SUPPORT@THERMASOL .COM | WWW.THERMASOL .COM WWW.THERMASOL .
