Cut Sheet
Table Of Contents
- T&B Fitting
- Product Overview
- Rigid & Intermediate Metal Conduit Fittings
- Form 7, Form 8, Series 35, Conduit Outlet Bodies & Covers
- Mogul Conduit Outlet Bodies
- FS/FD Cast Device Boxes and Covers
- Conduit Outlet Boxes
- Conduit Outlet Elbows, Reducers, Plugs, and Adapters
- Three-Piece Couplings
- Sealing Fittings
- Kopr-Shield Compound
- Jacketed Metal Clad Cable Termination Fittings
- Tray Cable Fittings
- EMT Fittings
- Liquidtight Flexible Metal Conduit Fittings
- Shureflex™ Nylon Conduit System
- XTRA FLEX System
- Flexible Cord and Cable Fittings
- Flexible Cord and Cable Fittings - Non-Metallic
- Service Entrance Cable Fittings
- Metal Clad Cable, Armored Cable and FlexibleMetal Conduit Fittings
- Non-Metallic Sheathed Cable Fittings
- Conduit Dimensional Data
XTRA FLEX
®
System —
Conduit, Tubing, Fittings for Non-Metallic Liquidtight Conduit
Plastic Bullet
®
Liquidtight Fittings for T&B LTC Non-Metallic
Liquidtight Conduit Type B and T&B EFC Flexible Tubing
This engineering breakthrough meets the
demand for a tough, reusable, non-metallic
liquidtight fitting for use with XTRA FLEX
®
Type B conduit or flexible tubing. The BULLET
®
non-metallic fitting provides a reliable liquidtight
seal that combines high pullout resistance and
ease of installation.
Engineered to meet your needs.
The BULLET
®
non-metallic fitting meets your
performance requirements when terminating
Type B liquidtight non-metallic conduit or flexible
non-metallic tubing to a box or enclosure with
knockout opening or threaded hub. Fittings meet
the watertight requirements for NEMA Type 4
and Type 6 enclosures and conform to UL514B
and CSA No. 22.2 #227.2 specifications.
Ease of installation.
Installations can be performed quickly and easily
because BULLET
®
liquidtight fittings can be
installed without disassembly. BULLET
®
non-
metallic fittings are resistant to numerous
caustics and solvents.
The BULLET
®
fitting is economical because it can
be used over and over again without sacrificing
the quality of the original seal. When used with
the XTRA FLEX
®
raceway system, you can meet
most machine or industrial requirements where
liquidtight protection is needed.
Corrosion-resistant. Built to take it.
The BULLET
®
liquidtight fitting is manufactured
from weather-resistant thermoplastic materials
and is suitable for indoor or outdoor corrosive
environments. The BULLET
®
fitting is resistant to
detergents, cleaners, oils, sanitizers, paints,
cutting fluids and wire pulling compounds —
just about any liquid usually found in industrial,
plant or marine environments. It also surpasses
industry standards for cold impact and simulated
hammer blows.
C
B*
A
E
THREAD
D
FIGURE 1
(STRAIGHT)
C
F*
B*
A
E
THREAD
D
FIGURE 2
(45 DEGREE)
C
F*
B*
A
E
THREAD
D
FIGURE 3
(90 DEGREE)
C ±.015 (0.40) MIN. E
TRADE A ±.015 ACROSS THROAT THREAD F*
SIZE (.040) *B ±.035 (0.90) CORNERS DIA. D NPT (IN.) (MM)
CAT. NO.
FIG. (IN.) (IN.) (MM) (IN.) (MM) (IN.) (MM) (IN.) (MM) (IN.) APPROX.
LT38P 1 .570 1.595 (40.51) 1.354 .417 –
LT438P 2
3
⁄8 (14.48) 2.012 (51.10) (34.39) (10.59)
1
⁄2-14 1.534 (38.95)
LT938P 3 1.380 (35.05) 1.880 (47.75)
LT50P 1 .570 1.636 (41.55) 1.448 .550 –
LT450P 2
1
⁄2 (14.48) 2.092 (53.14) (36.78) (13.97)
1
⁄2-14 1.590 (40.39)
LT950P 3 1.489 (37.82) 1.986 (50.44)
LT75P 1 .582 1.757 (44.63) 1.740 .740 –
LT475P 2
3
⁄4 (14.78) 2.452 (62.28) (44.20) (18.80)
3
⁄4-14 1.821 (46.25)
LT975P 3 1.790 (45.47) 2.212 (56. )
LT100P 1 .726 1.923 (48.84) 2.068 .940 –
LT4100P 2 1 (18.44) 2.684 (68.17) (52.53) (23.88) 1-11
1
⁄2 2.034 (51.66)
LT9100P 3 2.104 (53.44) 2.508 (63.70)
LT125P 1 .750 2.164 (54.97) 2.494 1.257 –
LT4125P 21
1
⁄4 (19.05) 3.264 (82.91) (63.35) (31.93) 1
1
⁄4-11
1
⁄2 2.385 (60.58)
LT9125P 3 2.564 (65.13) 2.856 (72.54)
LT150P 1 .767 2.353 (59.77) 2.784 1.453 –
LT4150P 21
1
⁄2 (19.48) 3.605 (91.57) (70.71) (36.91) 1
1
⁄2-11
1
⁄2 2.604 (66.14)
LT9150P 3 2.854 (72.49) 3.144 (79.86)
LT200P 1 .794 2.605 (66.17) 3.362 1.883 –
LT4200P 2 2 (20.17) 4.210 (106.93) (85.39) (47.83) 2-11
1
⁄2 3.050 (77.47)
LT9200P 3 3.432 (87.17) 3.675 (93.34)
* After Assembly
UL File No. E-23018
CSA File No. 52391
The BULLET
®
non-metallic liquidtight fitting — easy to use, built to take it!
• Outside surface has friction-
reducing ridges
• Inner surface teeth bite into conduit
or tubing to enhance clamping and
sealing action
• Fitting ferrule designed to accept
variations in conduit sizes and field
conduit cuts
• Smooth ferrule profile reduces friction
to ensure a tight conduit-to-fitting seal
• Friction-reducing ridges and teeth
provide a true double seal and high
pullout resistance
• Elongated gland nut offers additional
strain relief for 90° pull and easy
hand grip
• Rugged low-profile nonmetallic body and
gland construction provides space savings
• Captivated sealing O-ring features
predetermined compression to provide
a reliable seal at enclosure
• Steel locknut firmly secures fitting
to box or enclosure
A-127
United States
Tel: 901.252.8000
800.816.7809
Fax: 901.252.1354
Technical Services
Tel: 888.862.3289
www.tnb.com