Manual

ManualsBrandsTippmann ManualsPaintballE-Grip

E-grip

lower receiver must be removed to install / replace battery.

❏

1) To do so, you must complete the instructions

“

STEP 1

”

(unload your

marker / remove air source / discharge stored air / uncock marker) before

further disassembly. – EXAMPLE: If you fail to remove the air source before

removing lower receiver, the marker will fire uncontrollably - possibly

resulting in personal injury and damage to the marker).

❏

2) Remove lower receiver as outlined in “STEP 2”

(it is not necessary to

remove tank adapter bolt

to replace battery).

❏

3) Remove trigger assembly from lower

receiver. (NOTE: It is not necessary to disassemble

the trigger assembly to install battery.

❏

Detach the

lower receiver

Remove 2 lower

receiver push pins

(

& ) to detach

from upper receiver

❏

Detach Tank

Adapter

from lower

receiver.

❏

Remove

receiver bolt

from lower receiver.

A-5

INSTALLATION INSTRUCTIONS

TIPPMANN

A-5

E-GRIP

KIT PN. 02-EG

Fits: A-5

Markers

KIT PN. 02-EG INCLUDES:

(1) 1 - E-GRIP

Lower Receiver Component

READ EACH STEP COMPLETELY BEFORE PERFORMING STEP

❏

1) Unload your marker: first remove the hopper. Then, point your marker

in a safe direction and fire several times to be sure there are no balls left in

the feeder or lodged in the chamber.

❏

2) Remove air source: To remove a charged air cylinder, turn the cylinder

approximately 3/4 of a turn counterclockwise

or out. This allows the tank pin

valve to close so that no air will enter the marker. Point the marker in a safe

direction and fire the remaining air in the marker by pulling the trigger until the

marker stops firing. (This may take 4-5 shots)

• If your marker keeps firing after you have turned the tank 3/4 of a turn, the

tank pin valve has not closed yet and you may have to turn the tank

counterclockwise

a little further.

• If you turn the tank 3/4 of a turn and it begins to leak before you pull the

trigger you have turned it too far and may have damaged the tank o-ring.

❏

3) After air tank is removed, point & fire the marker in a safe direction

until stored air is completely discharged.

❏

4) Put marker in the uncocked position: pull and hold the bolt

cocking handle back, then pull the trigger and slowly release the

handle forward

to un-cock the marker.

STEP 1: Prepare Marker for SAFE Disassembly before

beginning disassembly.

STEP 2: Prepare Marker for installation.

STEP 3: Battery Installation / Replacement

Set up a table with plenty of space to work. You Will Need: A ( )

1/8" allen wrench and a 9 volt battery. NOTE: Carefully hand start

threaded parts, do not over tighten and strip threads.

Dissassemble the marker: With Air Source removed & marker in the

uncocked position

as per STEP 1:

4-E A-5

Do not replace sear spring with

spring from old trigger assembly,

tensions are specifically designed

for E-GRIP

and it will not operate

properly if you do).

❏

To remove the

trigger assembly, push the safety

out of the left side of the lower

receiver and carefully lift the trigger

assembly out, keeping it intact

5-E A-5

NOTE: It is not necessary to

disassemble the lower receiver any

further to install/replace the battery.

(continued on page 5-E A-5

) (continued on page 6-E A-5

)

(A-5

INSTALLATION INSTRUCTIONS continued from page 4-E A-5

)

EYE PROTECTION DESIGNED FOR PAINTBALL USE MUST BE WORN AT

ALL TIMES WHEN HANDLING THIS MARKER BY THE USER AND ANY

PERSON WITHIN RANGE. DO NOT DISASSEMBLE THIS MARKER WHILE

IT IS PRESSURIZED WITH AIR. REMOVE AIR SUPPLY CYLINDER OR

CARTRIDGE BEFORE DOING ANY DISASSEMBLY. DISASSEMBLING THE

RECEIVER WHILE UNDER AIR PRESSURE WILL CAUSE PERSONAL

INJURY & /OR DAMAGE TO THE MARKER. DO NOT OPERATE THIS

MARKER WITH PARTS MISSING OR DAMAGED. IF DURING THE COURSE

OF THIS INSTALLATION, A PART IS LOST OR FOUND TO BE DAMAGED,

OBTAIN A REPLACEMENT PART BEFORE CONTINUING REASSEMBLY.

WARNING

(4)

Eye protection designed for paintball use must be worn by the user and any

person within range.