Manual

ManualsBrandsTippmann ManualsPaintballE-Grip

❏

10) Visually inspect E-GRIP

lower receiver, a top view with the

trigger assembly

and battery installed

should look like this.

❏

11) Attach Lower to Upper Receiver

❏

Align the E-Grip

lower receiver

front push pin hole

with upper receiver hole then gently rock rear of

grip to align upper & lower push pin hole

❏

With holes aligned, insert

two lower receiver push pins

and to attach.

6-E A-5

❏

Check that the trigger

assembly is intact

with

no gaps

; and the safety is in the “SAFE”

(pushed to the right and red not showing) position

❏

12) Attach Tank Adapter to E-Grip

TM.

❏

Remove receiver bolt from

lower receiver.

❏

Slide tank adapter into lower receiver and

align holes;

❏

Insert receiver bolt and tighten.

Installation is complete, continue on page 7-E - OPERATING

INSTRUCTIONS.

7-E

(Custom

or A-5

)

INSTALL THE AIR SUPPLY AND LOAD THE HOPPER WITH

PAINTBALLS ONLY AFTER YOU:

❏ ❏

❏

HAVE THE BARREL SLEEVE INSTALLED;

❏ ❏

❏

HAVE THE SAFETY IN THE "SAFE" POSITION;

❏ ❏

❏

HAVE SUCCESSFULLY INSTALLED THE BATTERY AND

❏ ❏

❏

ARE FAMILIAR WITH THE E-TRIGGER

NORMAL OPERATION (STEP

2: AND STEP 3:).

With the kit installation complete, read and follow these supplemental operating

instructions to the owner's manual FOR TIPPMANN A-5

WITH E-GRIP

98 CUSTOM

OR 98 CUSTOM PRO

WITH E-TRIGGER

marker with the

"EQUALIZER

LED BOARD INSTALLED before attempting to operate this

marker. Keep these instructions with your marker owner's manual. Eye protection

designed for paintball use must be worn by the user and any person within range.

WARNING

READ EACH STEP COMPLETELY BEFORE PERFORMING STEP:

STEP 1: Prepare the marker for safety before any programming:

OPERATING INSTRUCTIONS

(A-5

INSTALLATION INSTRUCTIONS continued from page 5-E A-5

)

(continued on page 8-E)

❏

4) Notice how

battery wires from

inside lower receiver

are in slot

beside top of

armature pin

and the position

of the armature pin

❏

To replace the battery, remove

old battery from inside the E-Grip

lower receiver. Do not jerk it out by the

wires, carefully take it out. If you turn the receiver upside down the armature

may come out, this is ok, just be sure to replace it.

❏

Carefully

remove battery clip

from old battery.

❏

5) Carefully attach battery clip to new battery. NOTE: battery

terminals only fit one way in clip.

❏

6) Make sure battery wires coming out of lower receiver are in slot

beside the armature pin .

❏

7) Make sure armature pin is properly positioned in lower receiver

and slides freely up and down.

❏

8) Insert attached battery into lower receiver

bottom first

with clip wires facing the back of the

receiver

and to the right .

NOTE: Make sure battery wires are not sitting on shelf

where the trigger assembly will rest.

❏

9) Insert Trigger Assembly and line up safety holes

❏

insert the safety from the left to hold the trigger assembly in place.

LED

Power

Button

❏ ❏

❏

1) To Turn ON the E-Trigger to normal operation - Ready To Fire:

STEP 2: NORMAL OPERATION:

Without holding the trigger: Use a small object

like an allen wrench to

❏

press and hold the power

button

for 1/2 second and then release the

power button. The LED

should light solid

Orange for 2 seconds, flash once (green in A-5s or

red in 98s) and then

light solid Green to show

normal operation - “Ready To Fire” mode.

• Your E-Trigger is now ready to fire in the SEMI-AUTO = 1 pull / release

of the trigger fires 1 time (Factory set Default Firing Mode).

NOTE: If pressing the power button failed to turn on LED light, see

troubleshooting on page 8-E.

❏ ❏

❏

2) To turn OFF the E-Trigger electronics.

❏

Press and hold the power

button for 2 seconds as the LED turns solid Red, then release the Power

Button and the LED will turn OFF. NOTE: The trigger electronics are set to

shut-off automatically after a prolonged period of inactivity (120 minutes).

❏❏

❏

3) To select a new firing mode:

❏

1) Turn ON the E-Trigger to normal operation (solid Green LED - Ready

To Fire) as instructed in step

1) above.

❏

2) Press / hold the power button in one time for more than 1/4 but less

than 2 seconds and release the power button.

❏

Count the LED Orange

NOTE: The E-Trigger Low Battery Indicator feature: the “Ready To Fire” solid

Green LED will turn to blinking red when the battery is low and needs replaced.

❏

TOURNAMENT LOCK: Because the E-Trigger board requires a tool to

turn it on and off, no tournament lock is necessary for competition paintball.