Manual

ManualsBrandsTippmann ManualsPaintballE-Grip

9-E

(Custom

or A-5

)

8-E

(Custom

or A-5

)

(continued on page 9-E)

(OPERATING INSTRUCTIONS continued from page 7-E)

(continued on page 10-E)

(OPERATING INSTRUCTIONS continued from page 8-E)

1) FIRST YOU MUST ENTER INTO THE “TRIGGER PROGRAMMING

MODE:” to access the Trigger Programming Menu:

❏

Make sure the

STEP 3: How to program a new Dwell, Debounce

, Rate Of

Fire Cap or Firing mode setting In the TRIGGER PROGRAMMING

MODE. (Example: Shows how to select a new firing mode).

❏

PROBLEM: You have successfully installed the battery, turned on the

E-Trigger, installed the air supply and loaded the paintballs and the marker

will not fire.

❏

Check to be sure safety is in "FIRE" position and

❏

make

sure sufficient air supply is hooked up to the marker. If a problem still

exists, call Tippmann

Service Department at 1-800-533-4831.

❏

PROBLEM: the “Ready To Fire” solid Green LED has turned to blinking

red -

❏

The E-Trigger has a Low Battery Indicator feature: the “Ready

To Fire” solid Green LED will turn to blinking red when the battery is low

and needs replaced.

❏

Replace the battery.

❏

PROBLEMS WHEN FIRING: You can fine tune how your marker fires

by making adjustments to the Dwell, Debounce

and Rate Of Fire Cap

modes. Read and become familiar with detailed descriptions of problems

you may have when firing and instructions for troubleshooting, tuning

and programming to correct them in STEP 3 - Dwell, Debounce

and

Rate Of Fire sections on pages 9-E, 10-E, 11-E and 12-E.

E-TRIGGER – TROUBLESHOOTING

❏

PROBLEM: The LED light does not light when you push the power button

and attempt to turn ON the E-Trigger in

STEP 2: NORMAL OPERATION.

1) Battery may be disconnected.

❏

Check battery clip connection.

2) Battery may be bad -

❏

Replace battery.

3) Internal wire may be disconnected. Do NOT disassemble a marker while

it is pressurized with air.

❏

Inspect wire connections inside the receiver:

• For 98 Custom

Markers follow the instructions on:

❏

page 1-E: Prepare marker for safe disassembly - STEP 1:

❏

page 2-E: Remove the battery - steps 1) and 2) of Battery Replacement;

❏

page 2-E: Disassemble marker - steps 1), 2), 3), 4), and 5 of STEP 2:

❏

page 3-E: Inspect wire connections - STEP 3:

❏

page 3-E: Reassemble Receiver - STEP 4:

Then continue on page 7-E with

STEP 2: Normal Operation. NOTE: If a

problem still exists, call Tippmann

Service Department at 1-800-533-4831.

• For A-5

Markers follow A-5

E-GRIP DISASSEMBLY / INSPECT

WIRES / ASSEMBLE below. Then continue on page 7-E with

STEP 2:

Normal Operation. NOTE: If a problem still exists, call Tippmann

Service Department at 1-800-533-4831.

❏

Replace left grip half , make sure that: (trigger switch ; sear

tripper board

; armature pin ; solenoid ; armature ; magnet ;

capacitor

; and trigger guard ) are in place and wires are positioned

in slot

and cutout areas so wires are not pinched or sheared and

the armature pin

moves freely.

❏

Secure the E-Grip

halves with 3

grip screws

❏

Attach Tank Adapter: Slide tank adapter into

lower receiver and

align holes;

❏

Insert receiver bolt and tighten.

❏

Follow E-Grip

Battery Installation or Replacement steps 5), 6), 7),

8), 9), 10), and 11) on page 6-E to reassemble. If a problem still exists,

call Tippmann

Service Department at 1-800-533-4831.

A-5

E-GRIP DISASSEMBLY / INSPECT WIRES / ASSEMBLE:

❏

Remove

lower receiver and trigger assembly as outlined in Marker/Receiver

Disassembly on page 5-E A-5

STEP 2.

❏

Remove the tank adapter bolt .

❏

Remove 3 grip screws holding the two lower E-GRIP

halves together.

❏

Visually inspect internal

wires for disconnected wire

end(s)

or damage.

flashes to identify your new setting, the LED light will return to solid Green -

Ready To Fire - in the new firing mode. You can program your marker for

any one of 5 firing modes. The orange flashes = firing mode options are:

• 1 orange flash = SEMI-AUTO MODE – 1 pull/release of the trigger fires

1 time (default firing mode). (This adheres to the 2005 NPPL rules).

• 2 orange flashes = 3 SHOT RAMPING MODE – 3 trigger pulls are

required (semi-auto) and the consecutive trigger pulls will fire 3 shots

per pull as long as the trigger is pulled at least 5 times per second.

(This adheres to the 2005 PSP rules).

• 3 orange flashes = 3 SHOT FULL AUTO MODE – 3 trigger pulls are

required (semi-auto) after which the trigger can he held to achieve full

auto firing. (This adheres to the 2005 NXL rules).

• 4 orange flashes = AUTO RESPONSE MODE – Fires one shot for each

pull or release of the trigger. If the trigger is held for more than 1/4 of a

second, when the trigger is released no shot is fired.

• 5 orange flashes = TURBO MODE – Fires one shot for each pull of the

trigger until the time between trigger pulls is less than 1/4 of a second

at which point it will fire on each trigger pull

and

trigger release.

❏

Repeat step 2) until you have the firing mode you want.

❏

You are now ready to complete the remaining steps in the GETTING

STARTED section of your owner’s manual: beginning with

STEP 2: Air

Supply Cylinder Installation. NOTE: If marker will not fire see page 8-E:

E-Trigger - Troubleshooting (below).