Manual
Table Of Contents
- 2 Einführung
- 3 Bestimmungsgemäße Verwendung
- 4 Lieferumfang
- 5 Zubehör
- 6 Aktuelle Bedienungsanleitungen
- 7 Symbol-Erklärung
- 8 Sicherheitshinweise
- 8.1 Allgemeine Sicherheitsinformationen
- 8.2 Sicherheit im Arbeitsbereich
- 8.3 Elektrische Sicherheit
- 8.4 Persönliche Sicherheit
- 8.5 Verwendung und Pflege
- 8.6 Verwenden und Warten von akkubetriebenen Elektrowerkzeugen
- 8.7 Service
- 8.8 Besondere Sicherheitsanweisungen
- 8.9 Ursachen für Rückschlag und Möglichkeiten zum Vermeiden
- 8.10 Verringerung von Geräuschen und Vibrationen
- 8.11 Restrisiken
- 8.12 Sicherheitsanweisungen für Akkus
- 8.13 Sicherheitsanweisungen für das Ladegerät
- 8.14 Wichtige Informationen zum Akku
- 9 Produktübersicht
- 10 Montage
- 11 Betrieb
- 12 Vor dem Arbeiten mit der Kettensäge
- 13 Arbeiten mit der Kettensäge
- 14 Nach dem Arbeiten mit der Kettensäge
- 15 Reinigung
- 16 Wartung
- 17 Transport und Aufbewahrung
- 18 Problembehandlung
- 19 Entsorgung
- 20 Konformitätserklärung (DOC)
- 21 Technische Daten
- 2 Introduction
- 3 Intended use
- 4 Delivery content
- 5 Accessories
- 6 Up-to-date operating instructions
- 7 Description of symbols
- 8 Safety instructions
- 8.1 General safety information
- 8.2 Work area safety
- 8.3 Electrical safety
- 8.4 Personal safety
- 8.5 Use and care
- 8.6 Using and maintaining battery-powered tools
- 8.7 Service
- 8.8 Special safety instructions
- 8.9 Causes of kickback and ways to prevent it
- 8.10 Reduction of noise and vibrations
- 8.11 Remaining risks
- 8.12 Safety instructions for battery
- 8.13 Safety instructions for charger
- 8.14 Important information on battery
- 9 Product overview
- 10 Assembly
- 11 Operation
- 12 Before working with the saw
- 13 Working with the saw
- 14 After working with the saw
- 15 Cleaning
- 16 Maintenance
- 17 Transport and storage
- 18 Troubleshooting
- 19 Disposal
- 20 Declaration of conformity (DOC)
- 21 Technical data
44
12 Before working with the saw
Every time before you work with the saw perform the following checks:
Check that the hand guard (12) is undamaged.
Check that the handles are clean, dry and free from oil and grease.
Check that all parts are correctly tted and undamaged.
Check that the chain catcher is in good condition and undamaged.
Check the chain tension.
Check the oil level. Rell oil if necessary.
Check that the power switch and the start inhibitor are working properly.
Check that the chain brake is working properly.
Important:
– Do not use the chain saw if it is damaged or not working properly.
– Damaged parts must be repaired or replaced before using the chain saw.
12.1 Checking the chain brake
The chain brake stops the chain immediately in the event of kickback.
1. Put the chain saw on the ground.
2. Start the chain saw.
3. Push the chain brake handle forwards. See Fig. 12 and Fig. 13.
The chain should stop immediately.
12.2 Checking the chain lubrication
Do not use the chain saw without adequate lubrication.
1. Rell oil if necessary.
2. Start the chain saw.
3. Hold the bar about 15 cm over a suitable surface for 15 seconds.
Æ If the chain lubrication is working properly, there are oil splashes on the surface.