Manual

ManualsBrandsTop Flite ManualsAir equipmentTOPQ8409

WARRANTY..... Top Flite

Models guarantees this kit to be free from

defects in both material and workmanship at the date of purchase. This

warranty does not cover any component parts damaged by use or

modification. In no case shall Top Flite’s liability exceed the original cost of

the purchased kit. Further, Top Flite reserves the right to change or modify

this warranty without notice. In that Top Flite has no control over the final

assembly or material used for final assembly, no liability shall be assumed

nor accepted for any damage resulting from the use by the user of the final

user-assembled product. By the act of using the user-assembled product,

the user accepts all resulting liability.

If the buyers are not prepared to accept the liability associated with the use

of this product, they are advised to return this kit immediately in new and

unused condition to the place of purchase.

Top Flite Models

3002 N. Apollo Dr., Suite 1

Champaign, IL 61822

Technical Assistance - Call (217) 398-8970

READ THROUGH THESE INSTRUCTIONS FIRST. THEY CONTAIN

IMPORTANT INSTRUCTIONS CONCERNING THE ASSEMBLY OF

THIS MODEL.

Congratulations for deciding to install a fully detailed, scale looking interior in your Top Flite Stinson SR9. This is a project that can be

as detailed or as simple as you care to make it – the choice is yours. We have provided the basic kit that can be assembled and painted

in a few hours. It represents a stock interior as delivered from the factory. The color scheme and minor surface details change from plane

to plane, so you may need to add extra goodies depending on the full-scale plane you modeled. By using this kit, some imagination and

your modeling experience, you can create a great looking interior that will “wow” them at the flying field.

SCALE INTERIOR KIT FOR THE GOLD EDITION STINSON SR9

TOOLS AND SUPPLIES

❏ 4oz. Aliphatic resin glue

❏ 1 oz. Thin CA (GPMR6002)

❏ Hobby knife and #11 blades

❏ Curved tip canopy scissors (HCAR0667)

❏ 220, 320 and 400-grit Wet-or-dry sandpaper

❏ Bar Sander (GPMR6170)

❏ Selection of small paint brushes

❏ Model enamel paint (Testors)

LEFTOVERS FROM AROUND

YOUR WORKSHOP

❏ Chrome trim tape – for seat belt buckles

❏ 1/4" balsa to raise the front seats to the

proper height

❏ Thin colored vinyl material to line the

interior of the doors and the floor (optional)

PARTS INCLUDED

STNGCIPL01..........(2) Front seats

STNGCIPL02..........(1) Rear seats

STNGCIPL03..........(1) Steering wheels (sheet of two)

STNGCIPL04..........(1) Instrument gauge lens

SCRW024...............(2) #2 x 3/8" Sheet metal screw

TAPE002.................(2) Black elastic tape

PIN001....................(3) #17 White head pin

PIN002....................(3) #28 White head pin

DOWEL004.............(2) 1/4" x 1" Wood dowel

BN40F05.................(1) Cockpit coaming

STNGCIIP...............(1) Laser-cut instrument panel

™

Summary of content (4 pages)

PAGE 1
™ SCALE INTERIOR KIT FOR THE GOLD EDITION STINSON SR9 WARRANTY..... Top Flite® Models guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This warranty does not cover any component parts damaged by use or modification. In no case shall Top Flite’s liability exceed the original cost of the purchased kit. Further, Top Flite reserves the right to change or modify this warranty without notice.
PAGE 2
ASSEMBLE THE SEATS: ❏ ❏ 1. Cut the front seat bottom and back on the embossed cut line. ❏ ❏ 5. Make pedestals from 1/4" balsa (not included). Cut two pieces 2-1/2" x 2-1/2" and glue them to the underside of the seat. This will raise the seats to the proper height.You may wish to add some leftover balsa to the front and back of the pedestal. This will close off the bottom of the seat as is shown on the cover photo of these instructions. This is optional. ❏ ❏ 2.
PAGE 3
❏ 6. Seat belts are cut from 1/4" dressmakers’ elastic (included in this kit). One end is glued to the seat bottom where the seat bottom and back come together. The other can be glued in place near the front of the seat. Some of the Stinson SR9 versions had seating for three people on the rear bench. Others had seating for two. We have provided enough material for the two front seats and up to three belts for the rear bench seat. The buckles can be cut from chrome tape or could be made from aluminum foil.