Operator's Manual

ManualsBrandsToro ManualsLawn MowersToro 21199HD

FormNo.3421-465RevA

TimeMaster

30inLawnMower

ModelNo.21199HD—SerialNo.400000000andUp

Operator'sManual

Introduction

Thisrotary-blade,walk-behindlawnmowerisintended

tobeusedbyresidentialhomeowners.Itisdesigned

primarilyforcuttinggrassonwell-maintainedlawns

onresidentialproperties.Itisnotdesignedforcutting

brushorforagriculturaluses.

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourproductproperlyandtoavoid

injuryandproductdamage.Youareresponsiblefor

operatingtheproductproperlyandsafely.

YoumaycontactTorodirectlyatwww.Toro.comfor

productandaccessoryinformation,helpndinga

dealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineT oroparts,or

additionalinformation,contactanAuthorizedService

DealerorT oroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.Figure1

identiesthelocationofthemodelandserialnumbers

ontheproduct.Writetheproductmodelandserial

numbersinthespaceprovided.

Important:Withyourmobiledevice,youcan

scantheQRcodeontheserialnumberdecal(if

equipped)toaccesswarranty,parts,andother

productinformation.

g226622

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhas

safetymessagesidentiedbythesafety-alertsymbol

(Figure2),whichsignalsahazardthatmaycause

seriousinjuryordeathifyoudonotfollowthe

recommendedprecautions.

g000502

Figure2

Safety-alertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanical

informationandNoteemphasizesgeneralinformation

worthyofspecialattention.

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemical

orchemicalsknowntotheStateof

Californiatocausecancer,birthdefects,

orreproductiveharm.

Theengineexhaustfromthisproduct

containschemicalsknowntotheStateof

Californiatocausecancer,birthdefects,

orotherreproductiveharm.

ItisaviolationofCaliforniaPublicResourceCode

Section4442or4443touseoroperatetheengineon

anyforest-covered,brush-covered,orgrass-covered

landunlesstheengineisequippedwithaspark

arrester,asdenedinSection4442,maintainedin

effectiveworkingorderortheengineisconstructed,

equipped,andmaintainedforthepreventionofre.

TheenclosedEngineOwner'sManualis

suppliedforinformationregardingtheUS

EnvironmentalProtectionAgency(EPA)and

theCaliforniaEmissionControlRegulationof

emissionsystems,maintenance,andwarranty.

Replacementsmaybeorderedthroughtheengine

manufacturer.

GrossorNetTorque:Thegrossornettorque

ofthisenginewaslaboratoryratedbytheengine

manufacturerinaccordancewiththeSocietyof

AutomotiveEngineers(SAE)J1940orJ2723.As

conguredtomeetsafety,emission,andoperating

requirements,theactualenginetorqueonthisclass

ofmowerwillbesignicantlylower.Pleasereferto

theenginemanufacturer’sinformationincludedwith

themachine.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedinMexico

AllRightsReserved

*3421-465*A

Summary of content (28 pages)

PAGE 1
Form No. 3421-465 Rev A TimeMaster® 30in Lawn Mower Model No. 21199HD—Serial No. 400000000 and Up Operator's Manual Introduction g000502 This rotary-blade, walk-behind lawn mower is intended to be used by residential homeowners. It is designed primarily for cutting grass on well-maintained lawns on residential properties. It is not designed for cutting brush or for agricultural uses.
PAGE 2
Contents Safety Introduction ............................................................... 1 Safety ....................................................................... 2 General Safety ................................................... 2 Safety and Instructional Decals .......................... 3 Setup ........................................................................ 5 1 Assembling and Unfolding the Handle.............. 5 2 Installing the Blade-Control Bar........................
PAGE 3
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decaloemmarkt Manufacturer's Mark 1. This mark indicates that the blade is identified as a part from the original machine manufacturer. decal125-5092 125-5092 1. Step on the mower housing to start the engine. decal94-8072 94-8072 decal131-4514b 131-4514 1. Warning—read the Operator's Manual. 2.
PAGE 4
decal132-4470 132-4470 Traction Adjustment 1. Attention; read the 2. Scan the QR code for Operator's Manual—1) more information on Loosen the knob by turning traction adjustment. it counterclockwise; 2) Pull the cable(s) away from the engine to decrease the traction, or push the cable(s) toward the engine to increase the traction; 3) Tighten the knob by turning it clockwise.
PAGE 5
Setup Important: Remove and discard the protective plastic sheet that covers the engine and any other plastic or wrapping on the machine. 1 Assembling and Unfolding the Handle No Parts Required Procedure WARNING Assembling and unfolding the handle improperly can damage the cables, causing an unsafe operating condition. • Do not damage the cables when unfolding the handle. • If a cable is damaged, contact an Authorized Service Dealer.
PAGE 6
2 Installing the Blade-Control Bar No Parts Required Procedure g225133 Figure 4 6
PAGE 7
3 Filling the Engine with Oil No Parts Required Procedure Important: Your machine does not come with oil in the engine, but it does come with a bottle of oil. Before starting the engine, fill the engine with oil.
PAGE 8
Product Overview g244723 Figure 8 Upper handle 1. Adjustment knob for the self-propel drive 4. Blade-control bar 2. Traction-assist handle 5. Engine-shutoff switch 3. Blade-control-bar lock g243960 Figure 7 1. Side-discharge deflector 8. Upper handle 2. Spark plug 9. Engine-shutoff switch 3. Recoil-start handle 4. Oil fill/dipstick 10. Rear deflector 11. Rear cutting-height lever 5. Handle-lock lever 6. Handle knob (2) 12. Air filter 13. Washout port 7.
PAGE 9
– Do not handle fuel when smoking or around an open flame or sparks. To ensure optimum performance and continued safety certification of the machine, use only genuine Toro replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be dangerous, and such use could void the product warranty. – Do not remove the fuel cap or add fuel to the tank while the engine is running or hot. – If you spill fuel, do not attempt to start the engine.
PAGE 10
g234916 Figure 10 2. Install the fuel-tank cap and tighten it securely by hand. Checking the Engine-Oil Level Service Interval: Before each use or daily Important: If the oil level in the crankcase is too low or too high and you run the engine, you may damage the engine.
PAGE 11
Adjusting the Handle Height You can raise or lower the handle to a position more comfortable for you. 1. Pull the handle-lock lever rearward to disengage the handle-lock pins (Figure 12). g191982 Figure 12 1. Handle-lock lever 2. Handle-lock pin (2) 3. Notches 2. Rotate the handle and align the desired notch in the handle bracket to the handle-lock pins; refer to Figure 12. 3. Release the handle-lock lever to secure the handle in place.
PAGE 12
Adjusting the Cutting Height CAUTION If the engine has been running, the muffler will be hot and can severely burn you. Keep away from the hot muffler. Note: To raise the machine, move the front and rear cutting-height levers forward; to lower the machine, move the cutting-height levers rearward. Set all the wheels to the same height unless special circumstances require otherwise; refer to Operating Tips (page 17). g224172 Figure 13 During Operation within 3 seconds.
PAGE 13
• • • • or deterioration and replace them with the manufacturer's recommended parts when necessary. machine to overturn or cause you to lose your balance or footing. If the machine strikes an object or starts to vibrate, immediately shut off the engine, remove the key (if equipped), wait for all moving parts to stop, and disconnect the wire from the spark plug before examining the machine for damage. Make all necessary repairs before resuming operation.
PAGE 14
Note: Use the traction-assist handle in situations when you need more control than you have with the self-propel drive alone. Shutting Off the Engine Press the toggle switch (Figure 16) to the STOP position and hold it until the engine shuts off. g193334 Figure 18 Disengaging the Blades Release the blade-control bar (Figure 19). g234921 Figure 16 Engaging the Blades g193345 When you start your engine, the blades do not turn. You must engage the blades to mow. 1.
PAGE 15
5. the rear-discharge chute until the latch locks into place; refer to Figure 19. While watching the bag, release the blade-control bar. Note: If the bag does not deflate within 3 seconds of releasing the blade-control bar, the blade-stop system may be deteriorating and, if ignored, could result in an unsafe operating condition. Have the machine inspected and serviced by an Authorized Service Dealer. 6. Shut off the engine and wait for all moving parts to stop. Not Using the Grass Bag 1.
PAGE 16
Bagging the Clippings Use the grass bag when you want to collect grass and leaf clippings from the lawn. If the side-discharge chute is on the mower, remove it before bagging the clippings; refer to Removing the Side-Discharge Chute (page 17). Installing the Grass Bag 1. Raise and hold up the rear door (A of Figure 21). 2. Remove the rear-discharge plug by pulling down on the latch with your thumb and pulling the plug out from the machine (B of Figure 21). 3.
PAGE 17
g244855 Figure 22 Removing the Side-Discharge Chute To remove the side-discharge chute, reverse the steps in Installing the Side-Discharge Chute (page 16). Operating Tips • Alternate the mowing direction. This helps General Mowing Tips • • Inspect the area where you will use the machine and remove all objects that the machine could throw. • Avoid striking solid objects with the blades. Never deliberately mow over any object.
PAGE 18
Hauling Safety WARNING • Remove the ignition key (if equipped) before A broken or missing washout fitting could expose you and others to thrown objects or blade contact. Contact with a blade or thrown debris can cause injury or death. loading the machine for hauling. Use care when loading or unloading the machine. Secure the machine from rolling. • • • Replace a broken or missing washout fitting immediately, before using the machine again.
PAGE 19
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 5 hours • Change the engine oil. Before each use or daily • • • • • Check the engine-oil level and add oil as needed. Check the blade-brake-clutch operation. Clean grass clippings and dirt from under the machine. Check the air filter and clean or replace it, if necessary. Check the cutting blades.
PAGE 20
WARNING Tipping the machine may cause the fuel to leak. Fuel is flammable, explosive, and can cause personal injury. Run the engine dry or remove the fuel with a hand pump; never siphon. 3. Clean the air-filter body and cover using a damp rag. Keep dirt away from the air opening. 4. Install the filter onto the base. 5. Install the cover and screw the fastener down securely.
PAGE 21
Adjusting the Self-Propel Drive Whenever you install a new self-propel cable or if the self-propel drive is out of adjustment, adjust the self-propel drive. 1. Turn the adjustment knob counterclockwise to loosen the cable adjustment (Figure 28). g017281 Figure 27 5. After draining the used oil, return the machine to the operating position. 6. Carefully pour about 3/4 of the engine capacity of oil into the oil-fill tube. 7. Wait 3 minutes for the oil to settle in the engine. 8.
PAGE 22
Servicing the Blade-Drive System 4. Servicing the Blades Service Interval: Every 50 hours 1. Install the blade-drive system cover that you previously removed. Remove the blade-drive system cover (Figure 29). Service Interval: Yearly Important: You will need a torque wrench to install the blades properly. If you do not have a torque wrench or are uncomfortable performing this procedure, contact an Authorized Service Dealer. Examine the blades whenever you run out of fuel.
PAGE 23
DANGER If you allow a blade to wear, a slot will form between the sail and flat part of the blade. Eventually a piece of the blade may break off and be thrown from under the housing, possibly resulting in serious injury to you or bystanders. • Inspect the blade periodically for wear or damage. • Never try to straighten a blade that is bent or weld a broken or cracked blade. • Replace a worn or damaged blade. 3. g025927 Figure 31 1. Handle locked in the vertical position 2.
PAGE 24
Removing the Blades Checking for Bent Blades 1. Rotate the blades to the position shown in Figure 33. Replace the blades when the machine hits a solid object or when a blade is out of balance or bent. Use only genuine Toro replacement blades. 1. Use a block of wood to hold each blade steady and turn the blade bolt counterclockwise as shown in Figure 34. g016532 Figure 33 1. Front of cutting deck 3. Measure from the cutting edge to a smooth, level surface g232790 Figure 34 2.
PAGE 25
Installing the Blades 1. Install the first blade so that it is horizontal, along with all mounting hardware as shown in Figure 35. Note: Tighten the bolt with your fingers. Important: Position the curved ends of the blades to point toward the machine housing. Be sure to nest the raised areas on each blade driver with the recesses in the head of its corresponding spindle, and the pins on the other side of each blade driver with the holes in its corresponding blade. 2. g016536 Figure 37 1.
PAGE 26
Storage 2. Store the machine in a cool, clean, dry place. Preparing the Engine General Information 1. Perform the recommended annual maintenance procedures; refer to Maintenance (page 19). 2. Clean under the machine housing; refer to Cleaning under the Machine (page 18). 3. Remove chaff, dirt, and grime from the external parts of the engine, the shrouding, and the top of the machine. 4. Check the condition of the blades; refer to Inspecting the Blades (page 23). 5.
PAGE 27
Notes:
PAGE 28