Form No. 3324–153 ProLine 10.
Introduction Thank you for purchasing a Toro product. All of us at Toro want you to be completely satisfied with your new product, so feel free to contact your local Authorized Service Dealer for help with service, genuine replacement parts, or other information you may require. Whenever you contact your Authorized Service Dealer or the factory, always know the model and serial numbers of your product.
Contents Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safe Operating Practices . . . . . . . . . . . . . . Toro Mower Safety . . . . . . . . . . . . . . . . . . Slope Chart . . . . . . . . . . . . . . . . . . . . . . . . . Safety and Instruction Decals . . . . . . . . . . . Gasoline and Oil . . . . . . . . . . . . . . . . . . . . . . . . Recommended Gasoline . . . . . . . . . . . . . . . Stabilizer/Conditioner . . . . . . . . . . . . . . . . Filling the Fuel Tank . . . . . . . .
Safety This machine meets or exceeds CPSC blade safety requirements for rotary mowers and the B71.4 1999 specifications of the American National Standards Institute, in effect at time of production. Note: The addition of certain attachments that do not meet American National Standards Institute certification will cause noncertification of this machine. Improper use or maintenance by the operator or owner can result in injury.
Safety Operation • Never run an engine in an enclosed area. • Only operate in good light, keeping away from holes and hidden hazards. • Be sure all drives are in neutral and parking brake is engaged before starting engine. Only start engine from the operator’s position. • Be sure of your footing while using pedestrian controlled equipment, especially when backing up. Walk, don’t run. Never operate on wet grass. Reduced footing could cause slipping. • • Slow down and use extra care on hillsides.
Safety • Disconnect battery or remove spark plug wire before making any repairs. Disconnect the negative terminal first and the positive last. Reconnect positive first and negative last. • Use care when checking blades. Wrap the blade(s) or wear gloves, and use caution when servicing them. Only replace blades. Never straighten or weld them. This product is designed for cutting and recycling grass or, when equipped with a grass bagger, for catching cut grass.
Safety Slope Operation Slopes and ramps are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death. All slopes and ramps require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it. • Service • Never store the machine or fuel container inside where there is an open flame, such as near a water heater or furnace. • Keep nuts and bolts tight, especially the blade attachment bolts. Keep equipment in good condition.
Safety Slope Chart Read all safety instructions on pages 2–8.
Safety 7
Safety Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost.
Safety " #%& $ #%& $ #%& $ ! #%& $ " #%& $ #%& $ 9
Gasoline and Oil Recommended Gasoline Use UNLEADED Regular Gasoline suitable for automotive use (85 pump octane minimum). Leaded regular gasoline may be used if unleaded regular is not available. IMPORTANT: Never use methanol, gasoline containing methanol, or gasohol containing more than 10% ethanol because the fuel system could be damaged. Do not mix oil with gasoline. POTENTIAL HAZARD • In certain conditions gasoline is extremely flammable and highly explosive.
Gasoline and Oil Stabilizer/Conditioner Filling the Fuel Tank Use a fuel stabilizer/conditioner in the machine to provide the following benefits: 1. Shut the engine off. 2. Clean around the fuel tank cap and remove the cap. Use a funnel and add unleaded regular gasoline to the fuel tank, until the level is 1/4 to 1/2 inch (6 mm to 13 mm) below the bottom of the filler neck. This space in the tank allows gasoline to expand. Do not fill the fuel tank completely full. 3.
Assembly Loose Parts Note: Use the chart below to verify all parts have been shipped. DESCRIPTION QTY.
Assembly DESCRIPTION QTY. Fuel tank 1 Bolt 5/16–1/ x 7/8” (22.5 mm) 2 Lock washer 5/16” 2 Washer 5/16” 4 Stud 2 Spring 2 Hose clamp 1 Operator’s Manual 1 Engine Operator’s Manual 1 Parts Catalog 1 Registration card 1 USE Install fuel tank Read before operating machine Fill out and return to Toro Install Front Castors Install Upper Handle 1. Align castors with holes on top and front of mower and insert (8) 3/8–16 x 3/4” (19 mm) bolts through mower.
Assembly Connect Wire Harness Install Traction Control Rods 1. 1. Thread trunnions equal distance onto each control rod. For a starting point thread on approximately 2 in. (51 mm) (Fig. 5). 2. With trunnion rod up, slide clevis pins through rod fittings and mounting holes in idler brackets (from outside) (Fig. 5). Secure with 1/4” (6 mm) washers and hairpin cotters (Fig. 5). 2. Route wire harness inside of frame, along left handle and over throttle cable.
Assembly 3. 4. 5. Check the gap between upper control bar and fixed bar with wheel drive fully engaged. Gap should be approximately 1 to 1-1/4 in. (25–32 mm) (Fig. 6). Connect Throttle Cable 1. Place throttle control lever in FAST position.(Fig. 7). Note: 2. Hook wire Z–bend into hole of control plate slide (Fig. 7). 3. Loosen cable clamp screw allowing cable installation, but do not tighten (Fig. 7). 4. Move control cable until hole in contorl plate slide is aligned with hole in control plate.
Assembly Install Blade Control (PTO) Rod 1. Rotate blade control lever (PTO) away from left handle so rod drops down. 2. Secure blade control (PTO) rod through hole in bellcrank with hairpin cotters (Fig. 8). 3. Replace the spring washer, dish down, and locknut (Fig. 8). 4. Torque nut to 35 ft. lbs. (47 N m). 5. Shift lever to second gear and check alignment of lever in slot of shifter plate.
Assembly Mount Fuel Tank 1. 5. Align fuel tank to top of rear frame and secure fuel tank right side with (2) 5/16–18 x 7/8 in. (22.5 mm) bolts, (2) 5/16 lock washers and (2) 5/16 washers (Fig. 10). 2. Torque bolts to 10 ft. lbs. (13 N•m). 3. Secure fuel tank left side to frame with (2) 5/16–18 x 7/8 in. (22.5 mm) studs, (2) 5/16 washers, (2) springs and (2) 5/16 locknuts (Fig. 10). 4. Push fuel line onto fuel tank fitting and secure with hose clamp (Fig. 11).
Operation Think Safety First Please carefully read all the safety instructions and symbols in the safety section. Knowing this information could help you, pets or bystanders avoid injury. Recoil Starter – Pull recoil starter handle to start engine. Fuel Shut–off Valve – (In fuel line) Close fuel shut–off valve when transporting or storing mower. 2 5 Controls 7 Become familiar with all the controls (Fig. 12) before you start the engine and operate the machine.
Operation Parking Brake Always set the parking brake when you stop the machine or leave it unattended. Setting the Parking Brake 1. Pull the upper control bar rearward and hold it in this position (Fig. 13). 2. Lift the parking brake lock up and gradually release the upper control bar (Fig. 13). The brake lock should stay in the set (locked) position. Releasing the Parking Brake 1. Pull rearward on the upper control bar (Fig. 13). Lower the parking brake lock to the released position. 2.
Operation Starting and Stopping the Engine Stopping 1. Note: Starting 1. Make sure spark plug wire(s) are installed on spark plug(s) and fuel valve is open. 2. Move the blade control to off, the shift lever to neutral and set the parking brake. 3. Move the throttle control to CHOKE position before starting a cold engine. 2. Note: 4. Move the throttle lever to “SLOW” (Fig. 14). A warm or hot engine usually does not require any choking.
Operation Operating Blade Control (PTO) The Safety Interlock System The blade control (PTO) lever engages and disengages power to the mower blades. Understanding the Safety Interlock System Engaging the Mower Blades (PTO) The safety interlock system is designed to prevent the engine from starting if: 1. Pull on the upper control bar to stop the machine (Fig. 15). • The throttle lever is all the way back, past SLOW 2. Hold the bail against the upper control bar (Fig. 15).
Operation Driving Forward or Backward The throttle control regulates the engine speed as measured in rpm (revolutions per minute). Place the throttle control in the “FAST” position for best performance. Forward 1. To go forward, move the shift lever to a forward gear. 2. Release the parking brake: refer to Releasing the Parking Brake, page 19. 3. Slowly press on the upper control bar to move forward (Fig. 16). To go straight, apply equal pressure to both ends of the upper control bar (Fig. 16).
Operation Lower Control Bar Operation 1 This procedure is for driving up a curb. This can be performed while driving forward or backward. 1. 2 Disengage the mower blades. POTENTIAL HAZARD • A blade can be bent or damaged when driving up a curb. Blades could break apart and pieces could be thrown at bystanders or at you as you use the mower. m–4185 Figure 18 1. Lower Control Bar engaged and mower in reverse. 2.
Operation Adjust Axle Height Adjusting Height-of-Cut A 1” to 4-1/4” range for height-of-cut can be achieved by adjusting blade spacers, rear axle height and front castor spacers. Use the Height-of-Cut chart on page 25 to select the combination required Adjust Blade Height Blades are adjusted by using the four, 1/4” spacers found on the blade spindle bolts. This allows a range, in 1/4” increments, of cutting height in any axle position.
Operation Adjust Caster Position 1. 2 1 Using the height-of-cut chart, adjust the caster spacers to match with the axle hole selected (Fig. 21). 2. Remove clevis pin, slide castor from support and change spacers (Fig. 21). 3. Install castor in support and insert clevis pin (Fig. 21). 3 m–3791 Figure 21 1. Clevis pin 2. 3/16” (5 mm) spacer 3. 1/2” (13 mm) spacer Height-of-Cut Chart Axle Position No.
Maintenance Service Interval Chart Service Operation Oil—check level Each Use 5 Hours 8 Hours 25 Hours 50 Hours 100 Hours X Oil—change* Storage Service X Initial X X Safety System—check X X Brakes—check X X Cutting Blades – check Wheel Bearings—grease* X X X X Transmission Couplers – grease* Idler Pivots – grease* X X X X X Belt Blade Idler Pivot – grease* X X All other fittings – grease X X Foam Air Cleaner—service* X X Paper Air Cleaner—replace* X X Spark Plug(s)—
Maintenance Cleaning the Foam and Paper Elements Air Cleaner 1. Service Interval/Specification Foam Element Foam Element: Clean and re-oil after every 25 operating hours. A. Wash the foam element in liquid soap and warm water. When the element is clean, rinse it thoroughly. Paper Element: Replace after every 100 operating hours. B. Dry the element by squeezing it in a clean cloth. C. Put one or two ounces of oil on the element (Fig. 23). Squeeze the element to distribute the oil.
Maintenance 2. Paper Element Engine Oil A. Lightly tap the element on a flat surface to remove dust and dirt (Fig. 24). Service Interval/Specification B. Change oil: Inspect the element for tears, an oily film, and damage to the rubber seal. IMPORTANT: Never clean the paper element with pressurized air or liquids, such as solvent, gas, or kerosene. Replace the paper element if it is damaged, defective, or cannot be cleaned thoroughly. • After the first 5 operating hours.
Maintenance Checking Oil Level Changing/Draining Oil 1. Park the machine on a level surface, disengage the blade control (PTO) and set the parking. 1. Start the engine and let it run five minutes. This warms the oil so it drains better. 2. Clean around the oil dipstick (Fig. 25) so dirt cannot fall into the filler hole and damage the engine. 2. 3. Unscrew the oil dipstick and wipe the metal end clean (Fig. 25).
Maintenance Tire Pressure Service Interval/Specification Maintain the air pressure in the front and rear tires as specified. Check the pressure at the valve stem after every 50 operating hours or monthly, whichever occurs first (Fig. 27). Check the tires when they are cold to get the most accurate pressure reading. Pressure: 15 psi (103 kPa) rear tires 25–30 psi (172–207 kPa) castor tires Figure 28 Daily or more often, before running engine, clean muffler area to remove all grass and debris (Fig.
Maintenance Checking the Spark Plug Spark Plug 1. Service Interval/Specification Look at the center of the spark plug(s) (Fig. 32). If you see light brown or gray on the insulator, the engine is operating properly. A black coating on the insulator usually means the air cleaner is dirty. Check the spark plug(s) after every 100 operating hours. Make sure the air gap between the center and side electrodes is correct before installing the spark plug.
Maintenance Cutting Blades To ensure a superior quality of cut, keep the blades sharp. For convenient sharpening and replacement, you may want to keep extra blades on hand. POTENTIAL HAZARD • A blade that is worn or damaged could break apart and pieces could be thrown at bystanders or at you as you use the mower. Inspecting the Blades 1. Inspect the cutting edges (Fig 33). If the edges are not sharp or have nicks, remove and sharpen the blades. Refer to Sharpening the Blades on page 34. 2.
Maintenance Checking for Bent Blades 1. Rotate the blades until the ends face forward and backward (Fig. 34). Measure from a level surface to the cutting edge of the blades (Fig. 35). Note this dimension. POTENTIAL HAZARD • A blade that is bent or damaged could break apart and pieces could be thrown at bystanders or at you as you use the mower. WHAT CAN HAPPEN • Pieces of blade that may be thrown could seriously injure or kill you or bystanders.
Maintenance Sharpening the Blades Installing the Blades 1. 1. Use a file to sharpen the cutting edge at both ends of the blade (Fig. 37). Maintain the original angle. The blade retains its balance if the same amount of material is removed from both cutting edges. Place the blade onto the bolt, over cone washer. Select proper number of spacer(s) for height-of-cut and slide bolt into spindle (Fig. 36).
Maintenance Greasing and Lubrication 2. Service Interval/Specification Lubricate the transmission couplers every 50 hours and idler arm pivots every 8 hours (Fig 40). Grease the areas shown and at intervals in Where to Add Grease section below. Grease more frequently when operating conditions are extremely dusty or sandy. 1 Grease Type: General-purpose grease. How to Grease 1. 2 Disengage the blade control (PTO) and set the parking brake. m–3797 Figure 40 2.
Maintenance Brake Service Interval/Specification Before each use, check brakes for proper operation. Always set the parking brake when you stop the machine or leave it unattended. If the parking brake does not hold securely, an adjustment is required. Checking the Brake 1. Park the machine on a level surface, disengage the blade control (PTO) and set the parking brake. 2. Rear wheels must lock when you try to push the machine forward or backward.
Maintenance Fuel Tank 4. Draining The Fuel Tank Pull the fuel line off the fuel filter (Fig. 44). Open fuel shut-off valve and allow gasoline to drain into a gas can or drain pan. Note: POTENTIAL HAZARD • In certain conditions gasoline is extremely flammable and highly explosive. WHAT CAN HAPPEN • A fire or explosion from gasoline can burn you, others, and cause property damage. HOW TO AVOID THE HAZARD • Drain gasoline from the fuel tank when the engine is cold. Do this outdoors in an open area.
Maintenance Fuel Filter Replacing the Wheel Belt Service Interval/Specification Service Interval/Specification Replace the fuel filter after every 100 operating hours or yearly, whichever occurs first. Check all belts after every 50 operating hours or monthly, whichever occurs first. Look for dirt, wear, cracks and signs of overheating. Replacing the Fuel Filter 1. Never install a dirty filter if it is removed from the fuel line.
Maintenance Replacing the Traction Belt 1. Stop the engine, set the parking brake and remove the spark plug wire(s). 2. Raise the rear of the machine and hold with jack stands. 3. Remove mower belt (Fig. 48). 4. Loosen pivot bolt enough to slide idler pulley in slot and remove traction belt from the engine and drive pulleys. 5. Install new belt around engine and drive pulleys (Fig. 47). 6. Slide idler pulley in engine frame to tension traction belt (Fig. 47). 7. Install the mower belt (Fig.
Maintenance Replacing the Mower Belt 3 1. Disengage the power take off (PTO), set the parking brake, and turn the ignition key to “OFF” to stop the engine. Remove the key and spark plug wire. 2. Remove the knobs and belt cover on mower. 3. Remove idler pulley and then remove worn belt (Fig. 48). 4 6 5 m–3860 Figure 49 4. Install new belt. 5. Install idler pulley. 6. Engage PTO and check belt tension. See Adjusting Mower Belt Tension, page 41. Note: 2 1 1. 1/16” (2mm)–1/8” (3mm) 2.
Maintenance Adjusting Mower Belt Tension Adjusting the Blade Brake Service Interval/Specification 1. Disengage the power take off (PTO), set the parking brake, and turn the ignition key to “OFF” to stop the engine. Remove the key and spark plug wire. Check belt tension after the first hour of operation and at least twice during the first 24 hours of operation. 1. 2. IMPORTANT: Belt must be tight enough to not slip during heavy loads while cutting grass.
Maintenance Adjusting Grass/Mud Scraper Replacing the Grass Deflector 1. Loosen the locknut holding scraper to the engine frame (Fig. 52). 1. Remove the locknut, bolt, spring and spacer holding deflector to the mounts (Fig. 53). 2. Rotate scraper until they align with center of pulley grooves (Fig. 52). 2. Straighten deflector mounts if they are bent (Fig. 53). 3. Tighten the locknut (Fig. 52). 3. Install new deflector between mounts with spacer and spring.
Maintenance Wiring Diagram 43
Maintenance Cleaning and Storage 1. Disengage the blade control (PTO), set the parking brake, and turn the ignition key to “OFF” to stop the engine. Remove the key. 2. Remove grass clippings, dirt, and grime from the external parts of the entire machine, especially the engine. Clean dirt and chaff from the outside of the engine’s cylinder head fins and blower housing. IMPORTANT: You can wash the machine with mild detergent and water. Do not pressure wash the machine.
Troubleshooting PROBLEM Engine g will not start,, starts hard,, or f il to kkeep running. fails i Engine g loses power. Engine g overheats. Machine does not drive. POSSIBLE CAUSES CORRECTIVE ACTION 1. Fuel tank is empty. 1. Fill fuel tank with gasoline. 2. Choke is not ON. 2. Move choke lever to ON. 3. Air cleaner is dirty. 3. Clean or replace air cleaner element. 4. Spark plug wire is loose or disconnected. 4. Install wire on spark plug. 5.
Troubleshooting PROBLEM Abnormal vibration. Uneven cutting g height. g Blades do not rotate. Blades do not stop when disengaged. g g 46 POSSIBLE CAUSES CORRECTIVE ACTION 1. Cutting blade(s) is/are bent or unbalanced. 1. Install new cutting blade(s). 2. Blade mounting bolt is loose. 2. Tighten blade mounting bolt. 3. Engine mounting bolts are loose. 3. Tighten engine mounting bolts. 4. Loose engine pulley, idler pulley, or blade pulley. 4. Tighten the appropriate pulley. 5.
The Toro Total Coverage Guarantee LCE A One-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair any Toro Product used for commercial, institutional, or rental purposes if defective in materials or workmanship.
