Setup Instructions

ManualsBrandsToro ManualsLawn MowersToro 39634

FormNo.3365-264RevB

CommercialWalk-BehindMower

AllCommercialFloatingandFixedDeckWalk-behindMowers

SetupInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Unfoldthecrate.

Nopartsrequired

–

Checkthetirepressure.

Number2generalpurposelithiumbase

ormolybdenumbasegrease.(Purchase

separately.)

1tube

Checktheidlerarmsforgrease.

(FloatingDeckModels)

Number2generalpurposelithiumbase

ormolybdenumbasegrease.(Purchase

separately.)

1tube

Checkthemowerbeltidlerarmfor

grease.(FixedDeckModels)

Nopartsrequired

–

Preparethegrassdeector.

Nopartsrequired

–

Adjusttheanti-scalprollers.(Floating

DeckModels)

Mufer

Curvedwasher

Mufershield

Bolt(M8x25mm)

Muferclamp

Mufershieldbracket

Sidelocknut

Installthemufer(ifneeded).

Nopartsrequired

–

Checktheengineoillevel.

Nopartsrequired

–

Addfueltothemachine.

Nopartsrequired

–

Checkthehydraulicoillevel.

Bulkelectrolytewith1.265specic

gravity(Purchasefromabatterysupply

outlet.)

ounces

ActivatethebatteryforMowerswith

ElectricStart.

Nopartsrequired

–

ChargethebatteryforMowerswith

ElectricStart.

Nopartsrequired

–

Checkthemachinebeforedeliveryto

thecustomer.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (12 pages)

PAGE 1
Form No. 3365-264 Rev B Commercial Walk-Behind Mower All Commercial Floating and Fixed Deck Walk-behind Mowers Setup Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 Description Use Qty. No parts required – Unfold the crate. No parts required – Check the tire pressure. 3 Number 2 general purpose lithium base or molybdenum base grease. (Purchase separately.) 1 tube Check the idler arms for grease.
PAGE 2
Procedure 14 Description Operator’s Manual Engine Owner’s Manual Engine warranty literature Registration Card Operator training material Accessory brochure Key Oil drain hose 2 Qty. Use 1 1 1 1 1 1 1 1 Delivering the machine to the customer.
PAGE 3
1 3 Unfolding the Crate Checking the Idler Arms for Grease (Floating Deck Models) No Parts Required Parts needed for this procedure: Procedure 1 tube If the machine is in a metal crate, refer to the Packaging Crate Instructions included with the machine. Number 2 general purpose lithium base or molybdenum base grease. (Purchase separately.) Procedure 2 1. Remove the carrier frame cover. 2. Check the mower belt idler arm for grease (Figure 2 or Figure 3). Checking the Tire Pressure 3.
PAGE 4
Figure 4 5 Preparing the Grass Deflector Figure 3 36 inch Mower Deck shown No Parts Required 4. Under the engine deck, check the PTO drive belt idler arm for grease. Procedure Check if your machine has the grass deflector spring installed correctly. The grass deflector needs to have downward tension.
PAGE 5
7 Installing the Muffler Parts needed for this procedure: Figure 5 Fixed Deck Shown 1. Grass Deflector 2. Spring 3. J hook end of spring 4. L end of spring, place behind deck edge before installing bolt 5. Deck edge 1 Muffler 4 Curved washer 1 Muffler shield 4 Bolt (M8 x 25mm) 1 Muffler clamp 1 Muffler shield bracket 4 Side lock nut Procedure 1. Slide the muffler clamp onto the muffler inlet and slide the muffler onto the exhaust manifold (Figure 6). 2.
PAGE 6
1 2 3 9 Adding Fuel to the Machine 3 No Parts Required 11 Procedure 6 8 5 Add gasoline to the machine before starting it. Refer to your Operator’s Manual. for the correct fuel and procedure. 4 10 7 10 Checking the Hydraulic Oil Level for Mowers with Hydro Drive 9 g013784 Figure 6 1. 2. 3. 4. 5. 6. Muffler shield Curved washer Bolt, M8 x 25mm Muffler shield bracket Side lock nut Bracket attached to the engine 7. 8. 9. 10. 11.
PAGE 7
11 Activating the Battery for Mowers with Electric Start Parts needed for this procedure: 80 Bulk electrolyte with 1.265 specific gravity (Purchase ounces from a battery supply outlet.) Figure 7 Procedure 3. Slowly pour electrolyte into each battery cell until the level is up to the upper line on the battery case. WARNING Important: Do not overfill the battery because electrolyte (sulfuric acid) can cause severe corrosion and damage to the chassis.
PAGE 8
Important: Do not run the machine with the battery disconnected; electrical damage may occur to the engine. 12 Charge the battery. Refer to the Operator’s Manual for instructions. Charging the Battery for Mowers with Electric Start No Parts Required Procedure WARNING Charging the battery produces gasses that can explode and cause serious injury. • Keep cigarettes, sparks and flames away from the battery. • Make sure the ignition switch is off.
PAGE 9
14 Delivering the Machine to the Customer Parts needed for this procedure: 1 Operator’s Manual 1 Engine Owner’s Manual 1 Engine warranty literature 1 Registration Card 1 Operator training material 1 Accessory brochure 1 Key 1 Oil drain hose Procedure At delivery, Fill in the model and serial number and complete the items listed in the following table and initial each when finished. Model No. Serial No.
PAGE 10
Dealer Initial Customer Initial Check Procedure Show the customer where the following features are located and how they function: • Fuel tank cap • Oil fill cap/Oil dipstick • Spark plug(s) • Engine oil filter • Engine oil drain • Fuel filter • Air filter • Hydraulic fluid reservoir (if applicable) • Hydraulic filter (if applicable) • Hydraulic bypass valves (if applicable) • Battery (if applicable) • Ignition switch • Throttle lever • Choke lever • Power take off switch (PTO)
PAGE 11
Notes: 11
PAGE 12