TOSHIBA Thermal Printer B-SA4TP SERIES Owner’s Manual Mode d’emploi Bedienungsanleitung Manual de instrucciones Gebruikershandleiding Manuale Utente Manual do Utilizador
CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. VORSICHT: • Schallemission: unter 70dB (A) nach DIN 45635 (oder ISO 7779) • Die für das Gerät Vorgesehene Steckdose muß in der Nähe des Gerätes und leicht zugänglich sein. Centronics is a registered trademark of Centronics Data Computer Corp. Microsoft is a registered trademark of Microsoft Corporation. Windows is a trademark of Microsoft Corporation.
TOSHIBA Thermal Printer B-SA4TP SERIES Owner's Manual
Waste Recycling information for users: Following information is only for EU-member states: The use of the crossed-out wheeled bin symbol indicates that this product may not be treated as general household waste. By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
Safety Summary ENGLISH VERSION EO1-33048 Safety Summary Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment. Do not attempt to effect repairs or modifications to this equipment.
Safety Summary ENGLISH VERSION EO1-33048 If foreign objects (metal fragments, water, liquids) enter the machines, first turn off the power switches and disconnect the power cord plugs from the outlet, and then contact your authorised TOSHIBA TEC representative for assistance. Continued use of the machine in that condition may cause fire or electric shock. Ensure that the equipment is Connect a properly grounded. Extension grounding wire. cables should also be grounded.
ENGLISH VERSION EO1-33048 TABLE OF CONTENTS Page 1. PRODUCT OVERVIEW......................................................................................................... E1- 1 1.1 1.2 1.3 1.4 1.5 2. Introduction................................................................................................................... E1- 1 Features ....................................................................................................................... E1- 1 Accessories .......................
ENGLISH VERSION EO1-33048 5. TROUBLESHOOTING .......................................................................................................... E5- 1 5.1 5.2 5.3 Error Messages ............................................................................................................ E5- 1 Possible Problems ........................................................................................................ E5- 3 Removing Jammed Media...........................................................
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33048 1.1 Introduction 1. PRODUCT OVERVIEW 1.1 Introduction Thank you for choosing the TOSHIBA B-SA4TP series thermal printer. This Owner’s Manual contains from general set-up through how to confirm the printer operation using an online test print, and should be read carefully to help gain maximum performance and life from your printer. For most queries please refer to this manual and keep it safe for future reference.
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33048 1.3 Accessories 1.3 Accessories NOTE: As a power cord is not supplied with this printer, please purchase one that meets each country’s safety standard. For details, refer to APPENDIX 3. When unpacking the printer, please make sure all the following accessories are supplied with the printer. Start-up CD-ROM (1 pc.
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33048 1.4 Appearance 1.4 Appearance The names of the parts or units introduced in this section are used in the following chapters. 238 (9.4) 339 (13.3) 1.4.1 Dimensions 332 (13.1) Dimensions in mm (inches) 1.4.2 Front View Ribbon Cover Top Cover LCD Message Display Operation Panel Top Cover Release Button Media Outlet Front Cover Power Switch O: OFF I: ON 1.4.
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33048 1.4 Appearance 1.4.4 Operation Panel LCD Message Display ON LINE LED (Green) ERROR LED (Red) [PAUSE] key [FEED] key [RESTART] key Please see Section 3.1 for further information about the Operation Panel. 1.4.5 Interior WARNING! 1. Do not touch the Print Head or around it just after printing. You may get burned as the Print Head becomes very hot during printing. 2. Do not touch any moving parts. To reduce the risk of fingers, jewellery, clothing, etc.
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33048 1.5 Options 1.5 Options Option Name 300-dpi Print Head Type B-SA704-TPH3-QM-R Cutter module B-SA204-QM-R Strip module B-SA904-H-QM-R Serial Interface Board Wireless LAN Board RFID module B-SA704-RS-QM-R Usage This print head enables a conversion of a 203-dpi print head of the B-SA4TM-GS12/B-SA4TP-GS12 model into a 300-dpi print head. This option is intended for use when you desire to print Kanji (Chinese characters) or to obtain clearer print.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2. PRINTER SETUP 2. PRINTER SETUP This section outlines the procedures to setup your printer prior to its operation. The section includes precautions, loading media and ribbon, connecting cables, setting the operating environment of the printer, and performing an online print test. Setup Flow Procedure Reference Installation After referring to the Safety Precautions in this manual, install the printer on a safe and stable location. 2.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.2 Connecting the Power Cord As the enclosure of this product is made from plastic, do not install the printer where it might be exposed to oil or solvent. To insure the best operating environment, and to assure the safety of the operator and the equipment, please observe the following precautions. • Operate the printer on a stable, level, operating surface in a location free from excessive humidity, high temperature, dust, vibration or direct sunlight.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.3 Loading the Media 2.3 Loading the Media WARNING! 1. Do not touch any moving parts. To reduce the risk of fingers, jewellery, clothing, etc., being drawn into the moving parts, be sure to load the media once the printer has stopped moving completely. 2. The Print Head becomes hot immediately after printing. Allow it to cool before loading the media. 3. To avoid injury, be careful not to trap your fingers while opening or closing the cover. CAUTION! 1.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.3 Loading the Media 2.3 Loading the Media (Cont.) 5. Put the Media Holder (Left) onto the Media Shaft. Push the Media Holder (Left) and the Media Holder (Right) against the media until the media is held firmly in place. This will automatically centre the media. Media Holder (Right) Media Holder (Left) 6. Fold the Release Lever to lock the Media Holder (Left). Media Holder (Left) Release Lever 7. Place the Media Holder Ass’y into the printer.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.3 Loading the Media 2.3 Loading the Media (Cont.) 9. Pull the media out of the front of the printer, and adjust the Media Guides to the media width. This will automatically centre the media. Media Guide CAUTION! Be sure to close the Upper Sensor Ass’y before closing the Top Cover. If the Upper Sensor Ass’y is opened, it may be damaged. 10. Lower the Upper Sensor Ass’y until the Upper Sensor Lever clicks into position.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.3 Loading the Media 2.3 Loading the Media (Cont.) 11. After loading the media, it may be necessary to set the position of the Media Sensor used to detect the print start position for label or tag printing. Setting the Feed Gap Sensor position When using a label stock without black marks, the Feed Gap Sensor is used to detect a print start position. (1) Push the Upper Sensor Lever inside and open the Upper Sensor Ass’y.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.3 Loading the Media 2.3 Loading the Media (Cont.) NOTES: 1. Be sure to set the Black Mark Sensor to detect the centre of the black mark, otherwise a paper jam or no paper error may occur. 2. After adjusting the Black Mark Sensor position, align the Upper Feed Gap Sensor with the Lower Feed Gap Sensor. This is because a paper end is detected by the Feed Gap Sensor.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.3 Loading the Media 2.3 Loading the Media (Cont.) 12. There are three issue modes available on this printer. How to set the media for each mode is provided below. Batch mode In the batch mode, the media is continuously printed and fed until the number of labels/tags specified in the issue command have been printed. (1) Pull the top edge of the media past the Platen. (2) Close the Top Cover until it clicks.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.3 Loading the Media 2.3 Loading the Media (Cont.) (2) Press down the Release Bar to open the Strip Unit. Release Bar Strip Unit NOTE: Be sure to close the Strip Unit completely. Failure to do this may cause a paper jam. (3) Remove enough labels from the leading edge of the media to leave 300mm of backing paper free. (4) Pass the backing paper through the opening under the Backing Paper Feed Roller. Then, close the Strip Unit until it clicks.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.3 Loading the Media 2.3 Loading the Media (Cont.) WARNING! The cutter is sharp, so care must be taken not to injure your fingers when handling the cutter. CAUTION! 1. When using a label stock, be sure to cut the gaps. Cutting labels will cause the glue to stick to the cutter, which may affect the cutter quality and shorten the cutter life. 2. Use of tag paper which thickness exceeds specified value may affect the cutter life.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.4 Loading the Ribbon 2.4 Loading the Ribbon WARNING! 1. Do not touch any moving parts. To reduce the risk of fingers, jewellery, clothing, etc., being drawn into the moving parts, be sure to load the ribbon once the printer has stopped moving completely. 2. The print head becomes hot immediately after printing. Allow it to cool before loading the ribbon. 3. To avoid injury, be careful not to trap your fingers while opening or closing the cover.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.4 Loading the Ribbon 2.4 Loading the Ribbon (Cont.) 3. Lower the Top Cover to its 45° angle open position. While pushing the Top Cover Stopper, raise the Top Cover again. This will fix the Top Cover. Top Cover 45° Top Cover Stopper 4. Open the Ribbon Cover. Ribbon Cover 5. Fit the ribbon take-up core into the Ribbon Holder (Take-up side), aligning the notch of the ribbon core with the protrusion of the Ribbon Stopper.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.4 Loading the Ribbon 2.4 Loading the Ribbon (Cont.) 7. Close the Ribbon Cover until it clicks. Ribbon Cover WARNING! Be sure to close the Ribbon Cover before closing the Top Cover. It is dangerous to close the Top Cover with the Ribbon Cover opened, as the Ribbon Cover slams shut. Top Cover 8. Gently close the Top Cover until it clicks.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.5 Connecting the Printer to Your Host Computer 2.5 Connecting the Printer to Your Host Computer NOTE: When using the USB interface, fix the USB Interface Cable to the printer back with the supplied Cable Clamp and the SMW-3x8 screw. The following paragraphs outline how to connect your host computer to the printer, and will also show how to make cable connections to other devices.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.6 Turning the Printer ON 2.6 Turning the Printer ON CAUTION! When the printer is connected to your host computer it is good practice to turn the printer ON before turning on your host computer and turn OFF your host computer before turning off the printer. 1. To turn ON the printer power, press the Power Switch as shown in the diagram below. Note that ( | ) is the power ON side of the switch. Use the power switch to turn the printer On/Off.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.7 Setting an Operating Environment 2.7 Setting an Operating Environment Depending on the settings of your host computer or an interface to be used, it may be necessary to change the printer parameter settings. Follow the procedures described below to change the printer parameter settings in the System Mode to correspond to your environment. ON LINE [PAUSE] PAUSE NOTE: Incorrect settings can cause the printer to function erroneously.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.7 Setting an Operating Environment 2.7.1 How to Enter the System Mode This section describes how to enter the System Mode. 1. Turn on the printer and confirm that “ONLINE” appears on the LCD Message Display. ONLINE B-SA4T V1.0 P 2. Press the [PAUSE] key to pause the printer. PAUSE B-SA4T V1.0 3. Hold down the [RESTART] key for three seconds until “<1>RESET” is displayed. R 4.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.7 Setting an Operating Environment 2.7.2 Parameter Setting (Cont.) The Parameter Setting Mode contains sub menus for selecting a language and setting the communication parameters. Each time the [PAUSE] key is pressed, the sub menus are displayed sequentially. <2>PARAMETER SET [PAUSE] <2>PARAMETER SET SPEED 9600bps Baud rate selection [PAUSE] <2>PARAMETER SET DATA LENG.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.7 Setting an Operating Environment 2.7.2 Parameter Setting (Cont.) Serial (RS-232C) Interface The following parameters of the RS-232C interface can be set: Baud rate Data length Stop bit Parity Flow control Set these in accordance with the setting of your host computer. Properties screen of Serial (COM) port under Windows98 NOTES: 1. Choose a desired baud rate by using the [RESTART] or [FEED] key. 2.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.7 Setting an Operating Environment 2.7.2 Parameter Setting (Cont.) Serial (RS-232C) Interface (2) Data Length This parameter is to choose a data length of the RS-232C interface. As “8 bits” has been chosen as default, change it in accordance with your PC. <2>PARAMETER SET DATA LENG. 8bits [RESTART] DATA LENG. 8bits [FEED] DATA LENG. 7bits After making a choice, press the [PAUSE] key.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.7 Setting an Operating Environment 2.7.2 Parameter Setting (Cont.) Serial (RS-232C) Interface NOTES: 1. When using the hardware flow control, the control signals and data must be in pairs between the printer and the PC. Printer TD RD RTS CTS DSR DTR → ←→ ←→ ←- Host RD TD CTS RTS DTR DSR Refer to the RS-232C connector’s pin layout in APPENDIX 2. Check if the printer and the PC is properly connectable with your cable 2.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.7 Setting an Operating Environment 2.7.2 Parameter Setting (Cont.) Parallel (Centronics) Interface This parameter is to choose an ACK/BUSY timing of the parallel interface. “TYPE1” has been chosen as default, but if a communication error occurs or a communication is not properly made, change to “TYPE2”. <2>PARAMETER SET ACK/BUSY TYPE1 [RESTART] ACK/BUSY TYPE1 [FEED] ACK/BUSY TYPE2 After making a choice, press the [PAUSE] key.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.7 Setting an Operating Environment 2.7.2 Parameter Setting (Cont.) Plug & Play This parameter is to enable or disable the plug & play function. As “OFF” has been chosen as default, change it when this function is used. If the printer and the PC are connected by USB, plug & play will be automatically enabled, regardless of the setting of this parameter.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.7 Setting an Operating Environment 2.7.3 IP Address Setting (TCP/IP) Power OFF When the printer is connected to a PC through TCP/IP by using a LAN cable, it is necessary to set an IP address in the System Mode for system administrators. The System Mode for system administrators consists of the following menus. While holding down the [FEED] and [PAUSE] keys, turn on the printer. <1>DIAG. Vx.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.7 Setting an Operating Environment 2.7.3 IP Address Setting (TCP/IP) (Cont.) P F In this section, how to set the IP address is described. First, you need to access the System Mode for system administrators. 1. While holding down the [FEED] and [PAUSE] keys, turn on the printer. 2. When “<1>RESET” appears on the LCD Message Display, release the [FEED] and [PAUSE] keys. <1>DIAG. Now, the printer is in the System Mode for system administrators. F 3.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.7 Setting an Operating Environment 2.7.3 IP Address Setting (TCP/IP) (Cont.) The IP Address Setting Mode contains the following sub menus. To enter each sub menu, press the [PAUSE] key.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.7 Setting an Operating Environment 2.7.3 IP Address Setting (TCP/IP) (Cont.) (2) Gateway IP Address This parameter is to set a Gateway IP address. <7>IP ADDRESS GATEWAY IP ADRES NOTE: After the last 3-digit value is set, press the [PAUSE] key to go to Subnet Mask Setting. [PAUSE] <7>IP ADDRESS 192 . 168 . 010 . 020 [PAUSE] <7>IP ADDRESS 192 . 168 . 010 . 020 [PAUSE] <7>IP ADDRESS 192 . 168 . 010 . 020 [PAUSE] <7>IP ADDRESS 192 . 168 . 010 .
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.7 Setting an Operating Environment 2.7.3 IP Address Setting (TCP/IP) (Cont.) (4) Socket Port This parameter is to enable a socket port and set a socket number. SOCKET PORT 1. 2. 3. 4. 5. NOTES: Pressing the [PAUSE] key while “PORT ON 08000” is displayed allows you to set the port number. Set a number for each digit by using the [RESTART] or [FEED] key.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.7 Setting an Operating Environment 2.7.3 IP Address Setting (TCP/IP) (Cont.) 1. 2. 3. 4. NOTES: Code used to enter a DHCP client ID is selectable between ASCII code (alphanumeric) and Hex code. Set a character or value for each byte by using the [RESTART] or [FEED] key. [RESTART] key: Increment [FEED] key: Decrement Press the [PAUSE] key to enter the next byte. Repeat this until 16th byte is entered.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.8 Installing the Printer Drivers 2.8 Installing the Printer Drivers 2.8.1. Introduction This manual describes how to install the TOSHIBA printer driver for the TOSHIBA B-SA4T bar code printer on your Windows host computer; install and delete the printer driver, the procedure for adding the LAN port, cautions and limitations. The appropriate version of the printer driver is V6.9. 2.8.2.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.8 Installing the Printer Drivers 2.8.3. Installing the Printer Driver The installation procedure differs depending on the interface connected to the printer and the operation system you are using. Please install the printer driver by performing the appropriate procedure. If the previous version of the printer driver has been installed on your host computer , be sure to uninstall it before you install this printer driver. (Refer to Section 2.8.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.8 Installing the Printer Drivers Windows 95/98/Me (1) Select “Settings” – “Printers” from the “Start” menu to open the printer folder. (2) Double-click on the “Add Printer” icon. The Add Printer Wizard runs. Click on the [Next] button. (3) Select “Local printer”, then click on the [Next] button. The screen listing “Manufacturers and Printers” is displayed. (4) Click on the [Have Disk…] button. The “Install From Disk” dialog box is displayed.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.8 Installing the Printer Drivers Windows NT4.0 (1) Log on to your host computer as a member who has full control access privilege concerning the printer settings. (2) Select “Settings” – “Printers” from the “Start” menu to open the printer folder. (3) Double-click on the “Add Printer” icon. The Add Printer Wizard runs. Click on the [Next] button. (4) Select “My Computer”, then click on the [Next] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.8 Installing the Printer Drivers Windows 2000/XP (1) Log on to your host computer as a member who has full control access privilege concerning the printer settings. (2) Select “Settings” – “Printers” from the “Start” menu to open the printer folder. (3) Double-click on the “Add Printer” icon. The Add Printer Wizard runs. Click on the [Next] button. (4) Select “Local printer”.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.8 Installing the Printer Drivers (2) USB INTERFACE Installation starts by the operating system’s plug-and-play function. Windows 95 and Windows NT4.0 do not support the USB interface. Windows 98/Me (1) Turn the printer ON, then connect it to your host computer with the USB cable. The “New Hardware Found” dialog box is displayed, and “USB Device” is detected. (2) After a while, the “Add New Hardware Wizard” dialog box is displayed.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.8 Installing the Printer Drivers (3) Select “Search for the best driver for your device. (Recommended)”. Mark the “Specify a location” checkbox, then click on the [Browse] button. Specify “\driver\WinMe-9x” folder, then click on the [Next] button. (4) Check to see that the “USB Printing Support” driver is detected, then click on the [Next] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.8 Installing the Printer Drivers (5) When the screen which indicates the USB Printing Support driver has been installed, is displayed, click on the [Finish] button. (6) After a while, “TEC B-SA4T” is detected as a new hardware. (7) The “Add New Hardware Wizard” dialog box is displayed. Select “Specify the location of the driver (Advanced)”, then click on the [Next] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.8 Installing the Printer Drivers (8) Select “Search for the best driver for your device. (Recommended)”. Mark the “Specify a location” checkbox, then click on the [Browse] button. Specify “\driver\WinMe-9x” folder, then click on the [Next] button. (9) Check to see that the “TEC B-SA4T” driver is detected, then click on the [Next] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.8 Installing the Printer Drivers (10) Change the printer name if necessary, and select whether or not you use the printer as the default printer (“Yes” or “No”). Click on the [Finish] button. (11) When the screen, which indicates TEC B-SA4T has been installed, is displayed, click on the [Finish] button. (12) When installation is completed, the new printer icon is added in the “Printers” folder.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.8 Installing the Printer Drivers Windows 2000/XP NOTE: When plug-and-play printer installation in progress is stopped, be sure to delete the printer detected and displayed on the “Device Manager” tab of the “System Properties” dialog box. (1) Log on to your host computer as a member who has full control access privilege concerning the printer settings. (2) Turn the printer ON, then connect it to your host computer with the USB cable.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.8 Installing the Printer Drivers (6) Select “Search for the best driver in these locations”. Mark the “Include this location in the search” checkbox, then click on the [Browse] button. Specify the “\driver\WinXP-2000” folder in the CD-ROM, then click on the [Next] button. (7) When the dialog box below is displayed, click on the [Continue Anyway] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.8 Installing the Printer Drivers (8) When the “Completing the Found New Hardware Wizard” screen is displayed, click on the [Finish] button. (9) When installation is completed, the new printer icon is added in the “Printers” folder.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.8 Installing the Printer Drivers 2.8.4. Uninstalling the Printer Driver NOTE: Before uninstalling the printer driver, be sure to complete all of printing, the status monitor, and properties settings. Windows 95/98/ME (1) Select “Settings” – “Printers” from the “Start” menu to open the printer folder. (2) Right-click on the printer driver icon to be deleted, then select “Delete”. The confirmation message is displayed. (3) Click on the [Yes] button to delete.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.8 Installing the Printer Drivers 2.8.5 Adding/Deleting a LAN Port To use the LAN interface, first, you have to make the following settings in “<7> IP ADDRESS” in the system mode of the printer. (Refer to Section 2.7.3) • Set the printer IP address (“PRINTER IP ADRES”), the gateway IP address (“GATEWAY IP ADRES”), and subnet mask (“SUBNET MASK”). • Set the port number (“SOCKET PORT”).
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.8 Installing the Printer Drivers Windows NT4.0/2000/XP (1) Right-click on the printer icon. Select “Properties” to open the printer “Properties” dialog box. (2) Select the “Ports” tab, and click on the [Add Port…] button. The “Printer Ports” dialog box is displayed. (3) Select “Seagull Scientific TCP/IP Port” from the “Available Printer Ports” list, then click on the [OK] button.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.8 Installing the Printer Drivers 2.8.6 Cautions (1) Printer Driver Upgrades • To upgrade the printer driver to this version, uninstall the previous version of the printer driver, before installing this printer driver. • Be sure to restart your host computer, after you upgrade the printer driver.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.8 Installing the Printer Drivers 2.8.7 Using the Printer Driver For how to use the Printer Driver, please refer to the Help for Windows Printer Drivers screen. 1) Open the Properties screen of the Printer Driver. 2) Clicking on the About tab causes the following screen to appear. Click on the [Help] button. About tab [Help] button 3) The Help for Windows Printer Drivers screen appears. This screen will provide how to use the printer driver.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.9 Print Test 2.9 Print Test After your operating environment has been set, perform a print test. 1. Perform a print test by using the Printer Driver or an Issue Command. The printer driver’s Properties screen allows you to set the communication conditions, media size, and other printing conditions in accordance with your operating environment. For details, refer to the Help for the Windows Printer Drivers screen.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.9 Print Test 2.9 Print Test (Cont.) When using an optional Cutter Module or Strip Module It is necessary to set the issue mode, cut/strip position, etc. for the Printer Driver or TPCL (TEC Printer Command Language) in accordance with your printing condition. For details of the TPCL, refer to the B-SA4T Series External Equipment Interface Specification stored in the CD-ROM.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.10 Position and Print Tone Fine Adjustment 2.10 Position and Print Tone Fine Adjustment This section describes how to fine adjust a print start position, cut/strip position, reverse feed amount, print tone, and ribbon motor torque. When a fine adjustment is required, such as print start position, print tone, etc, follow the procedure below. 1. Turn on the printer and confirm that “ONLINE” appears on the LCD Message Display. ONLINE B-SA4T V1.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.10 Position and Print Tone Fine Adjustment 2.10 Position and Print Tone Fine Adjustment (Cont.) The Parameter Fine Adjustment Mode contains sub menus for adjusting a print start position, cut/strip position, print tone, ribbon motor torque, and setting the threshold. Each time the [PAUSE] key is pressed, the sub menus are displayed sequentially. <3>ADJUST SET [PAUSE] <3>ADJUST SET FEED ADJ.+10.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.10 Position and Print Tone Fine Adjustment 2.10 Position and Print Tone Fine Adjustment (Cont.) Print Start Position Fine Adjustment <3>ADJUST SET FEED ADJ.+10.0mm FEED ADJ.+50.0mm NOTES: Choose a desired value by using the [RESTART] or [FEED] key. Pressing the [FEED] key one time causes a –0.1mm change, up to –50.0 mm. Pressing the [RESTART] key one time causes a +0.1mm change, up to +50.0 mm. [RESTART] FEED ADJ.+49.9mm FEED ADJ.+0.1mm FEED ADJ.+0.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.10 Position and Print Tone Fine Adjustment 2.10 Position and Print Tone Fine Adjustment (Cont.) NOTES: Choose a desired value by using the [RESTART] or [FEED] key. Pressing the [FEED] key one time causes a –0.1mm change, up to –50.0 mm. Pressing the [RESTART] key one time causes a +0.1mm change, up to +50.0 mm. Cut/Strip Position Fine Adjustment <3>ADJUST SET CUT ADJ. +10.0mm CUT ADJ.+50.0mm [RESTART] CUT ADJ.+49.9mm CUT ADJ.+0.1mm CUT ADJ.+0.0mm CUT ADJ.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.10 Position and Print Tone Fine Adjustment • Example of Strip Position Fine Adjustment When setting +3.0 mm Compared with “+0.0mm” position, the stop position after printing is shifted forward. Print Head Label Platen Strip Plate Backing Paper Stop position after printing 3mm When setting +0.0 mm Stop position after printing 3mm When setting –3.0 mm Compared with “+0.0mm” position, the stop position after printing is shifted backward.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.10 Position and Print Tone Fine Adjustment 2.10 Position and Print Tone Fine Adjustment (Cont.) NOTES: Choose a desired value by using the [RESTART] or [FEED] key. Pressing the [FEED] key one time causes a –0.1mm change, up to –9.9 mm. Pressing the [RESTART] key one time causes a +0.5mm change, up to +9.9 mm. Reverse Feed Amount Fine Adjustment <3>ADJUST SET BACK ADJ. +5.0mm BACK ADJ.+9.9mm [RESTART] BACK ADJ.+9.8 mm BACK ADJ.+0.1mm BACK ADJ.+0.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.10 Position and Print Tone Fine Adjustment 2.10 Position and Print Tone Fine Adjustment (Cont.) NOTES: Choose a desired value by using the [RESTART] or [FEED] key. Pressing the [FEED] key one time causes a –0.1mm change, up to –99.9 mm. Pressing the [RESTART] key one time causes a +0.1mm change, up to +99.9 mm. X Coordinate Fine Adjustment <3>ADJUST SET X ADJUST +5.0mm X ADJUST +99.9mm [RESTART] X ADJUST +99.8mm X ADJUST +0.1mm X ADJUST +0.0mm X ADJUST -0.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.10 Position and Print Tone Fine Adjustment 2.10 Position and Print Tone Fine Adjustment (Cont.) Print Tone Fine Adjustment Thermal Transfer Print <3>ADJUST SET TONE ADJ. +3 NOTES: Choose a desired value by using the [RESTART] or [FEED] key. Pressing the [FEED] key one time causes a –1 tone change, up to –10 tones. Pressing the [RESTART] key one time causes a +1 tone change, up to +10 tones. TONE ADJ. +10 [RESTART] TONE ADJ. +9 TONE ADJ.
2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.10 Position and Print Tone Fine Adjustment 2.10 Position and Print Tone Fine Adjustment (Cont.) Ribbon Motor Voltage Fine Adjustment When the ribbon is slack or wrinkled and printing is affected, fine adjust the ribbon motor torque by using the following procedure. Take-up Motor (RBN ADJ ) NOTES: Choose a desired value by using the [RESTART] or [FEED] key. Pressing the [FEED] key one time causes a –1 step change, up to –15 steps.
2.PRINTER SETUP ENGLISH VERSION EO1-33048 2.11 Threshold Setting 2.11 Threshold Setting To maintain a constant print position the printer uses the media sensor to detect a print start position according to the difference of voltage between a print area and a gap or black mark. When the media is pre-printed, the darker (or more dense) inks can interfere with this process causing paper jam errors. To get around this problem, first, try an automatic threshold setting.
2.PRINTER SETUP ENGLISH VERSION EO1-33048 2.11 Threshold Setting 2.11 Threshold Setting (Cont.) 7. Select the sensor to be adjusted by using the [FEED] key. REFLECTIVE B-SA4T V1.0A Black mark sensor 8. PAUSE B-SA4T ONLINE B-SA4T V1.0 TRANSMISSIVE B-SA4T V1.0A Feed gap sensor Press and hold the [PAUSE] key until more than 1.5 labels (tags) have been issued. The media will continue to be fed until the [PAUSE] key is released.
2.PRINTER SETUP ENGLISH VERSION EO1-33048 2.11 Threshold Setting 2.11 Threshold Setting (Cont.) Manual threshold setting procedure If a paper jam error still occurs even after an automatic threshold setting has been performed, manually set the threshold voltage. To make a threshold value manually set in this section effective, select the Transmissive Sensor (when using manual threshold value) or Reflective Sensor (when using manual threshold value) within software commands or the printer driver.
2.PRINTER SETUP ENGLISH VERSION EO1-33048 2.11 Threshold Setting 2.11 Threshold Setting (Cont.) <5>SENSOR ADJ. The Sensor Adjustment Mode contains sub menus for displaying the current status of each sensor and for storing “media level” voltage and “no media level” voltage. Each time the [PAUSE] key is pressed, the sub menus are displayed sequentially. [PAUSE] <5>SENSOR ADJ. [H]28°C [A]28°C [PAUSE] <5>SENSOR ADJ. [REFLECT] 3.
2.PRINTER SETUP ENGLISH VERSION EO1-33048 2.11 Threshold Setting 2.11 Threshold Setting (Cont.) <5>SENSOR ADJ. [REFLECT] 3.5V (3) Press and hold the [RESTART] or [FEED] key for about 3 seconds aligning a blank part of print area with the Black Mark Sensor. <5>SENSOR ADJ. [REFLECT] 4.8V* (4) When storing a “media level” voltage is completed, an asterisk “*”is displayed on the right side of a voltage. Press the [PAUSE] key. <5>SENSOR ADJ. [TRANS.] 2.
2.PRINTER SETUP ENGLISH VERSION EO1-33048 2.11 Threshold Setting 2.11 Threshold Setting (Cont.) Storing a “No Media Level” Voltage The following is how to set a “No media level” voltage that is used to detect a paper end. If a “NO PAPER” is displayed even if the media has not run out yet, this voltage needs to be set again. (1) Remove any media from the Black Mark Sensor/Feed Gap Sensor. <5>SENSOR ADJ. [PE]R0.1V T4.
2.PRINTER SETUP ENGLISH VERSION EO1-33048 2.11 Threshold Setting 2.11 Threshold Setting (Cont.) The Parameter Fine Adjustment Mode contains sub menus for adjusting a print start position, cut/strip position, print tone, etc., and setting a threshold. For details, refer to Section 2.10 Print Position and Print Tone Fine Adjustment. Each time the [PAUSE] key is pressed, the sub menus are displayed sequentially. (3) While “<3>ADJUST SET.
3. ON LINE OPERATION ENGLISH VERSION EO1-33048 3.1 Operation Panel 3. ON LINE OPERATION This chapter describes usage of the keys on the Operation Panel in On Line mode. When the printer is in On Line mode and connected to a host computer, the normal operation of printing images on labels or tags can be accomplished. 3.1 Operation Panel The figure below illustrates the Operation Panel and key functions.
3. ON LINE OPERATION ENGLISH VERSION EO1-33048 3.2 Operation 3.2 Operation When the printer is turned on, the “ON LINE” message appears on the LCD Message Display. It is shown during standby or normal printing. 1. The printer is turned on, standing by, or printing. ON LINE B-SA4T V1.0A 2. If any error occurs during printing, an error message appears. The printer stops printing automatically. (The number on the right side shows the remaining number of media to be printed.
4. MAINTENANCE ENGLISH VERSION EO1-33048 4.1 Cleaning 4. MAINTENANCE 1. 2. 3. 4. WARNING! Be sure to disconnect the power cord before performing maintenance. Failure to do this may cause an electric shock. To avoid injury, be careful not to pinch your fingers while opening or closing the cover and print head block. The print head becomes hot immediately after printing. Allow it to cool before performing any maintenance. Do not pour water directly onto the printer.
4. MAINTENANCE ENGLISH VERSION EO1-33048 4.1 Cleaning 4.1.1 Print Head/Platen/ Sensors (Cont.) 5. Wipe the Platen and Dumper Roller with a soft cloth slightly moistened with absolute ethyl alcohol. Remove dust or foreign substances from the internal part of the printer. 6. Wipe the Feed Gap Sensor and Black Mark Sensor with a dry soft cloth. 7. Wipe the media path. Dumper Roller Feed Gap Sensor/ Black Mark Sensor Platen 4.1.2 Covers and Panels 1. 2. 3. 4.
4. MAINTENANCE ENGLISH VERSION EO1-33048 4.1 Cleaning 4.1.3 Optional Cutter Module 1. Open the Front Cover. 2. Loosen the Set Screw of the Cutter Unit to open it. 3. Remove jammed media, if any. Set Screw Cutter Unit Cutter Unit WARNING! As the cutter blade is sharp, care should be taken not to injure yourself when cleaning. 4. Clean the inside of the Cutter Blade with a cotton swab moistened with absolute ethyl alcohol.
4. MAINTENANCE ENGLISH VERSION EO1-33048 4.1 Cleaning 4.1.4 Optional Strip Module 1. Open the Front Cover holding its right side. Front Cover 2. Press down the Release Bar to open the Strip Unit. Release Bar Strip Unit 3. Remove jammed media or backing paper, if any 4. Wipe the Backing Paper Feed Rollers, Guide Roller, and Strip Roller with a soft cloth slightly moistened with absolute ethyl alcohol.
5. TROUBLESHOOTING ENGLISH VERSION EO1-33048 5.1 Error Messages 5. TROUBLESHOOTING This chapter lists the error messages, possible problems, and their solutions. WARNING! If a problem cannot be solved by taking the actions described in this chapter, do not attempt to repair the printer. Turn off and unplug the printer, then contact an authorised TOSHIBA TEC service representative for assistance. 5.1 Error Messages NOTES: 1.
5. TROUBLESHOOTING ENGLISH VERSION EO1-33048 5.1 Error Messages 5.1 Error Messages (Cont.) Error Messages CUTTER ERROR **** Problems/Cause The media is jammed in the cutter. (When an optional cutter module is installed.) NO PAPER **** 1. The media has run out. 2. The media is not loaded properly. RIBBON ERROR **** 3. The media is slack. 1. The ribbon is not fed properly. 2. The ribbon has run out. EXCESS HEAD TEMP HEAD ERROR SYSTEM ERROR FLASH WRITE ERR.
5. TROUBLESHOOTING ENGLISH VERSION EO1-33048 5.2 Possible Problems 5.1 Error Messages (Cont.) Error Messages RFID ERROR SYNTAX ERROR Other error messages Problems/Cause The printer cannot communicate with the RFID module. While the printer is in the Dowload mode for upgrading the firmware, it receives an improper command, for example, a Issue Command. A hardware or software problem may have occurred. Solutions Turn the printer off, and then on again. Turn the printer off, and then on again.
5. TROUBLESHOOTING ENGLISH VERSION EO1-33048 5.3 Removing Jammed Media 5.3 Removing Jammed Media CAUTION! Do not use any tool that may damage the Print Head. NOTE: If you get frequent jams in the cutter, contact a TOSHIBA TEC authorised service representative. This section describes in detail how to remove jammed media from the printer. 1. Turn off and unplug the printer. 2. Press the Top Cover Release Button and gently open the Top Cover to its fully open position supporting it with your hand. 3.
6. PRINTER SPECIFICATIONS ENGLISH VERSION EO1-33048 6. PRINTER SPECIFICATIONS 6. PRINTER SPECIFICATIONS This section describes the printer specifications. Model Item B-SA4TP-GS12-QM B-SA4TP-TS12-QM Dimension (W × D × H) 238 mm × 339 mm × 332 mm (9.4” × 13.3” × 13.1”) Weight 26.5 lb (12 kg) (Media and ribbon are not included.
6. PRINTER SPECIFICATIONS ENGLISH VERSION EO1-33048 6.
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33048 7.1 Media 7. SUPPLY SPECIFICATIONS 7.1 Media Please make sure that the media being used is approved by TOSHIBA TEC. The warranty does not apply when a problem is caused by using media that is not approved by TOSHIBA TEC. For information regarding TOSHIBA TEC approved media, please contact a TOSHIBA TEC authorised service representative. 7.1.1 Media Type Two types of media can be loaded for this thermal transfer and direct thermal printer: label or tag.
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33048 7.1 Media NOTES: 1. To ensure print quality and print head life use only TOSHIBA TEC specified media. 2. The ratio of a label length to a gap length must be a minimum of 3 to 1 (3:1). 3. Backing paper must be wider than a label; the distance between the edge of the backing paper and that of a label should be at least 1.5 mm. 4. Use of the tag paper of 25 mm to 50 mm in width, and 171 µm to 263 µm in thickness may shorten the platen life. 5.
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33048 7.1 Media 7.1.3 Detection Area of the Reflective Sensor The Reflective Sensor is movable from the centre to the left edge of media. The reflection factor of the Black Mark must be 10% or lower with a waveform length of 950 nm. The Reflective Sensor should be aligned with the centre of the Black Mark. Centre of media Sensor should be positioned at the centre of the black mark. Detecting the black marks on the back. Min. 2.0 mm Min.
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33048 7.2 Ribbon 7.2 Ribbon Please make sure that the ribbon being used is approved by TOSHIBA TEC. The warranty does not apply to any problem caused by using non-approved ribbons. For information regarding TOSHIBA TEC approved ribbon, please contact a TOSHIBA TEC service representative. Type Width Length Outside Diameter Spool type 60 – 110 mm Recommended width is 60, 90, and 110 mm. 450 m (within ∅75 mm) ∅75 mm (max.
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33048 7.4 Care/Handling of Media and Ribbon 7.3 Recommended Media and Ribbon Types (Cont.) Ribbon type Vellum wax ribbon Standard wax ribbon Smear-less ribbon (Wax resin ribbon) Scratch and solvent resistance ribbon Description This ribbon is mainly used for vellum paper and labels. It has a very high ink density to cope with uneven printing surface Good match for coated paper (Matt coat and glossy coat). Good match for coated paper.
APPENDIX 1 MESSAGES AND LEDS ENGLISH VERSION EO1-33048 APPENDIX 1 MESSAGES AND LEDS APPENDIX 1 MESSAGES AND LEDS Appendix 1 describes the LCD messages displayed on the operation panel. Symbols in the message 1: : The LED is illuminated. ~: The LED is flashing. z: The LED is unlit. 2: ****: the number of unprinted media.
APPENDIX 1 MESSAGES AND LEDS ENGLISH VERSION EO1-33048 APPENDIX 1 MESSAGES AND LEDS LED Indication No.
APPENDIX 1 MESSAGES AND LEDS ENGLISH VERSION EO1-33048 APPENDIX 1 MESSAGES AND LEDS NOTE: Description of Command Error • If a command error is found in a command received, 16 bytes of the command error, starting from the command code, will be displayed. (However, [LF] and [NUL] will not be displayed.) Example 1 [ESC] T20 G30 [LF] [NUL] Command error The following message appears. T20G30 B-SA4T V1.0A Example 2 [ESC] XR; 0200, 0300, 0450, 1200, 1, [LF] [NUL] Command error The following message appears.
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33048 APPENDIX 2 INTERFACE APPENDIX 2 INTERFACE NOTE: To prevent radiation and reception of electrical noise, the interface cables must meet the following requirements: • In case of a parallel interface cable or serial interface cable, fully shielded and fitted with metal or metallised connector housings. • Keep as short as possible. • Should not be bundled tightly with power cords. • Should not be tied to power line conduits.
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33048 APPENDIX 2 INTERFACE Connector: PIN No.
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33048 APPENDIX 2 INTERFACE USB interface Standard: Transfer type: Transfer rate: Class: Control mode: Number of ports: Power source: Connector: Conforming to V2.0 Full speed Control transfer, Bulk transfer Full speed (12M bps) Printer class Status with the receive buffer free space information 1 Self power Type B Pin No. 1 2 3 4 Signal VCC DD+ GND Series B Plug LAN Standard: Number of ports: Connector: LED status: IEEE802.
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33048 APPENDIX 2 INTERFACE Serial interface (Option) Type: Communication mode: Transmission speed: Synchronization: Start bit: Stop bit Data length: Parity: Error detection: Protocol: Data input code: Receive buffer: Connector: RS-232C Full duplex 2400 bps, 4800 bps, 9600 bps, 19200 bps, 38400 bps, 115200 bps Start-stop synchronization 1 bit 1 bit, 2 bit 7 bit, 8 bit None, EVEN, ODD Parity error, Framing error, Overrun error Unprocedure communication ASCII code, E
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33048 APPENDIX 2 INTERFACE Wireless LAN (Option) Standard: Protocol: Security protocol: Antenna: Parameter setting: Default IP address: Default subnet mask: Conforming to IEEE802.11a, IEEE802.11b, and IEEE802.
APPENDIX 3 POWER CORD ENGLISH VERSION EO1-33048 APPENDIX 3 POWER CORD APPENDIX 3 POWER CORD When purchasing the power cord: Since the power cord set is not enclosed in this unit, please purchase an approved one that meets the following standard from your authorized TOSHIBA TEC representative.
APPENDIX 4 PRINT SAMPLES ENGLISH VERSION EO1-33048 APPENDIX 4 PRINT SAMPLES APPENDIX 4 PRINT SAMPLES The following are the image samples of the fonts, bar codes, and two-dimensional codes provided for the BSA4T series as standard. The size of each font may be different from the actual one. Font type and size can be specified by a command. For details, please refer to the B-SA4T Series External Equipment Interface Specification stored in the CD-ROM.
APPENDIX 4 PRINT SAMPLES ENGLISH VERSION EO1-33048 APPENDIX 4 PRINT SAMPLES APPENDIX 4 PRINT SAMPLES (Cont.
APPENDIX 4 PRINT SAMPLES ENGLISH VERSION EO1-33048 APPENDIX 4 PRINT SAMPLES APPENDIX 4 PRINT SAMPLES (Cont.
APPENDIX 4 PRINT SAMPLES ENGLISH VERSION EO1-33048 APPENDIX 4 PRINT SAMPLES APPENDIX 4 PRINT SAMPLES (Cont.
APPENDIX 5 GLOSSARIES ENGLISH VERSION EO1-33048 APPENDIX 5 GLOSSARIES APPENDIX 5 GLOSSARIES Bar code Feed gap sensor A code which represents alphanumeric characters by using a series of black and white stripes in different widths. Bar codes are used in various industrial fields: Manufacturing, Hospitals, Libraries, Retail, Transportation, Warehousing, etc. Reading bar codes is a fast and accurate means of capturing data while keyboard entry tends to be slow and inaccurate.
APPENDIX 5 GLOSSARIES ENGLISH VERSION EO1-33048 APPENDIX 5 GLOSSARIES Printer IP address Supply A 32-bit address of a printer connected to TCP/IP network, which identifies the network printer. An IP address is written as 4 sets of numbers, separated by periods. Media and ribbon Tag A type of media with no adhesive. Usually tags are made of cardboard or other durable material.
INDEX ENGLISH VERSION EO1-33048 INDEX INDEX A J Automatic threshold setting 2-1, 2-59 Jammed media 4-3, 4-4, 5-4 B L Backing paper 2-9, 2-54, 7-1 Bar code 6-2, A4-3, A5-1 Batch mode 2-8, 7-1, A5-1 Black mark 2-7, 7-1, 7-3, A5-1 Black mark length 7-1 Black mark sensor 2-7, 2-51, 2-62, 4-2, A5-1 Label 2-3, 2-10, 7-1, 7-2, 7-4 LCD message display 1-3, 1-4, 3-1, 6-1 LCD message language 2-21 C Centronics 1-3, 2-14, 2-22, 6-2, A2-1 Cut mode 2-10, 7-1, A5-1 Cut position 2-53, 7-1 Cutter module 1-1, 1-5,
INDEX ENGLISH VERSION EO1-33048 INDEX S Serial interface 1-1, 1-3, 2-14, 6-2, A2-4 Socket port 2-28 Strip mode 2-8, 7-1, A5-2 Strip module 1-1, 1-5, 2-8, 2-49, 4-4, 5-3, 6-2 Strip position 2-53, 2-54 Subnet mask 2-27 System mode 2-16, 2-17 T Tag 2-10, 7-1, A5-2 Thermal direct 2-57, 6-1, 7-1, A5-2 Thermal transfer 2-57, 6-1, 7-1, A5-2 Threshold setting 2-59, A5-2 Top cover 1-3, 2-3, 2-11, 5-1, A1-1 Top cover stopper 2-12 Two-dimensional code 6-2 U Upper sensor ass’y 2-3, 2-5, 5-4 Upper sensor lever 2-4,
M EO1-33048
