Version 1 Last Saved on 14/sep/01 5:47 Equium 8100D/M Equium 8100D/8100M User’s Manual User's Manual i Equium 8100D/M – 0000IMPR.
Equium 8100D/M Toshiba Equium™ 8100D/8100M User’s Guide Notices Important numbers for future reference Write down your computer’s serial number, part number, and Microsoft® Operating System Product Key Number here for future reference. These numbers are located on labels that are affixed to your computer and are easily accessible prior to set-up.
Version 1 Last Saved on 14/sep/01 5:47 Equium 8100D/M CE compliance This product and the original options are designed to observe the related EMC (Electromagnetic compatibility) and safety standards. However, Toshiba should not guarantee that this product still observes these EMC standards if options or cables not produced by Toshiba are connected or implemented.
Equium 8100D/M CD-ROM / DVD-ROM Safety Instruction The CD-ROM / DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorised service location. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
Version 1 Last Saved on 14/sep/01 5:47 Equium 8100D/M Copyright This manual is copyrighted by Toshiba Corporation with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein. © 2001 by Toshiba Corporation. All rights reserved.
Equium 8100D/M Trademarks IBM is a registered trademark and PS/2 is a trademark of IBM Corporation. MS-DOS, Microsoft, and Windows are registered trademarks of Microsoft Corporation. Intel and Pentium are registered trademarks, and Celeron is a trademark of Intel Corporation. DVDExpress is a trademark of Mediamatics, Inc.3Com and the 3Com logo are registered trademarks of the 3Com Corporation. Ethernet is a registered trademark of Xerox, Inc. WorldNet is a registered trademark of AT&T, Inc.
Version 1 Last Saved on 14/sep/01 5:47 Equium 8100D/M Safety Instructions for Toshiba Desktop and Minitower Computers Important Safeguards All safety instructions must be read carefully and must be fully understood, before attempting to use your Toshiba desktop or minitower Personal Computer (PC). This manual contains the safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries or could damage your computer.
Equium 8100D/M Computer Minitower WARNING: Never remove the cover or panels of the Computer Minitower, except as specifically instructed by Toshiba. Never attempt to disassemble the Minitower, to avoid the risk of electric shock or possible damage to the computer. Contact an authorised Toshiba service provider for assistance if repair or adjustment is necessary.
Version 1 Last Saved on 14/sep/01 5:47 Equium 8100D/M CD Writing Precautions Please adhere to the following information on the use of the CD-RW to minimise the risk of an unsuccessful storing process. As the storing may be unsuccessful despite your adhering to these information, for example because of a defective storing medium, you should even if the software indicates a successful storage, always check if the data has been stored successfully.
Equium 8100D/M Monitor DANGER: To avoid the risk of electric shock and exposure to high voltages, never remove the cover of the Cathode Ray Tube (CRT) Monitor for any reason. Contact an authorised Toshiba service provider for assistance if repair or adjustment is necessary. WARNING: To avoid the risk of injury from flying glass, never strike the face of the CRT with any object, and never drop the CRT monitor. Never install the CRT monitor in an unstable location from which it might fall.
Version 1 Last Saved on 14/sep/01 5:47 Equium 8100D/M Work Environment NOTE: This computer must always be used at a well designed work station. The keyboard and mouse-pad must be located so that your arms, shoulders and hands will always be in natural and comfortable positions when you are using the computer. This will minimise any physical discomfort to the back, neck, wrists and other parts of your body.
Equium 8100D/M WARNINGS: a. Always locate the CRT monitor directly in front of you, at a comfortable viewing distance, always greater than 40 cm (16") both for persons with normal eyesight as well as for those who wear corrective glasses or contact lenses. b. Always adjust the viewing angle to ensure that the top line of the CRT monitor screen is located at least 20 degrees below eye level.
Version 1 Last Saved on 14/sep/01 5:47 Equium 8100D/M Vision Care All new users of desktop PCs must have vision tests performed before undertaking computer use, and all users must have vision tests performed periodically thereafter, to ensure that they have adequately corrected their vision (if necessary) to satisfactorily handle such work. An association between bifocal use and vulnerability to neck disorders is also known to exist.
Equium 8100D/M Prevention of Physical Discomfort When using your Toshiba desktop PC for an extended period of time, prudent precautions must be taken to prevent physical discomfort to the body or to the hands, wrists and arms. Physical discomfort can be avoided by taking frequent rest breaks and by periodically initiating changes in activity, environment or work tempo.
Version 1 Last Saved on 14/sep/01 5:47 Equium 8100D/M Avoidance of Exposure to Electromagnetic Field (EMF) Emissions Extremely Low Frequency (ELF) Emissions (50Hz (Europe) or 60Hz (US)) NOTE: a. Since Toshiba desktop PCs are 50Hz or 60Hz alternating current (AC) devices, the power cord and power supply of this computer may emit low levels of EMF energy in the ELF range.
Equium 8100D/M Radio Frequency (RF) Emissions NOTE: All personal computers generate digital timing pulses at frequencies within the RF range, and consequently may emit minute levels of stray EMF energy in the RF range. As a result, all desktop PCs have been certified by the US Federal Communications Commission (FCC), by Industry Canada Requirements (ICES: Interference-Causing Equipment Standards) and by European Regulations and Standards (VDE, et al.) as being “Class B” digital devices.
Version 1 Last Saved on 14/sep/01 5:47 Equium 8100D/M Avoidance of Exposure to Emissions of Ionising Energy in the X-Ray Frequency Range Toshiba CRT monitors use a cathode ray tube monitor screen and are therefore an emissive device. They consequently are a generator of some ionising energy in the x-ray frequency range, as are all CRT monitors. Most of that energy is absorbed by the glass envelope of the CRT and is consequently not emitted.
Version 1 Last Saved on 19/sep/01 9:16 Table of Contents Equium 8100D/M Table of Contents Introduction About this guide................................................................................... xxiii Other documentation .......................................................................... xxiii Chapter 1 Getting Started Making sure you have everything ....................................................... 1-1 Creating a computer-friendly environment .....................................
Table of Contents Function, Ctrl and Alt keys ................................................................2-3 Numeric keypad ................................................................................2-3 Keyboard indicators ..........................................................................2-3 Modem and network communications................................................2-3 Connecting a modem ........................................................................
Version 1 Last Saved on 19/sep/01 9:16 Table of Contents Avoiding hardware conflicts ................................................................ 4-6 Installing a new IDE device.................................................................. 4-6 Adding a new device ........................................................................ 4-7 Configuring the new device .............................................................. 4-8 Partitioning and formatting a new hard disk drive ...............
Table of Contents Appendix B Video Modes MX200 .............................................................................................. B-1 VANTA .............................................................................................. B-2 Appendix C AC Power Cord and Connectors IEC60950 ............................................................................................... C-1 Appendix D Product Support If you need further assistance....................................................
Version 1 Last Saved on 23/sep/01 8:58 Equium 8100D/M Equium 8100D/M Introduction The Toshiba Equium 8100D/8100M is a build-to-order desktop computer that offers power and flexibility. About this guide This guide tells you about the computer’s features and options. You can: ■ Read it through. ■ Skim through and stop when a topic interests you. ■ Use the table of contents to find specific information.
Version 1 Last Saved on 25/sep/01 1:17 Getting Started Equium 8100D/M Chapter 1 Getting Started This chapter provides an overview of the Toshiba Equium 8100D/M computer, and explains how to set it up. Making sure you have everything Before you do anything else, consult the accompanying QuickStart to make sure you have received everything. Unpack the boxes and check the contents against your purchasing order.
Getting Started Keeping yourself comfortable Strain and stress injuries are becoming more common as people spend more time using their computers. However, with a little care and proper use of the equipment, computer work can be comfortable throughout the day. Using the computer keyboard incorrectly may result in discomfort and possible injury. If your hands, wrists, and/or arms bother you while typing, stop using the computer and rest. If the discomfort persists, consult a physician.
Version 1 Last Saved on 25/sep/01 1:17 Getting Started Seating and posture When using the computer, maintain good posture with your body relaxed and your weight distributed evenly. Proper seating is a primary factor in reducing work strain. Some people find a backless chair more comfortable than a conventional chair. Whichever type you choose, use the following guidelines to adjust your chair for maximum computing comfort.
Getting Started Lighting Proper lighting can improve the visibility of the display and reduce eyestrain. ■ Position the monitor so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows or shades to reduce glare. ■ Avoid placing the monitor in front of a bright light that could shine directly in your eyes. ■ If possible, use soft, indirect lighting in the computer work area.
Version 1 Last Saved on 25/sep/01 1:17 Getting Started Overview of the computer’s exterior The following illustration shows the front and back panels of the Toshiba Equium 8100D/M computer and the locations of the various ports and features. Front of the computer 1. USB Ports 5. CD-ROM/DVD-ROM Drive 2. Power Button 6. Drive Access Light 3. Power Light 7. Reset Button 4. Floppy Disk Drive Equium 8100D User's Manual 1-5 Equium 8100D/M – 01CHAP.
Getting Started 1 CD-ROM/DVD-ROM Drive 5. Reset Button 2. Floppy Disk Drive 6. Power Button 3. Power Light 7. USB Ports 4. Drive Access Light Equium 8100M Power button Press the Power button to suspend and resume the system. For normal shut down procedures, use the shutdown steps or menu options for your computer’s operating system. In case when the OS cannot shut down the system, press the Power button and hold it for approximately four (4) seconds to power off.
Version 1 Last Saved on 25/sep/01 1:17 Getting Started On Drive access light The drive-access light illuminates when the hard disk is in use. Power light The power light illuminates when power is on. ■ Green means the computer is in full-power mode. ■ Orange means the computer is sleeping (in Standby mode). ■ Unlit means the computer is turned off or is in Hibernation mode. The two USB ports connect USB devices.
Getting Started 5. Eject button To insert or remove a CD-ROM, press the eject button to open the drive tray. The eject mechanism requires power to operate. Do not press the eject button while the CD-ROM drive lamp is lit. Doing so could affect the system. If the CD-ROM drive is operational, quit the programs using the CD-ROM to bring the drive to halt. 6. Eject hole To open the drive tray when the computer is off, insert a slender object, such as a straightened paper clip, into the eject hole.
Version 1 Last Saved on 25/sep/01 1:17 Getting Started Floppy disk drive (FDD) Floppy disk drive control panel The Floppy disk drive is shown above. The floppy disk drive reads both high-density and double-density 3.5-inch floppy disks (1.44 MB/720 KB). 1. Disk access light Disk-access light the disk-access light glows while the floppy disk is being accessed. ■ ■ ■ ■ ■ To prevent loss of data, while the disk-access light is lit: Never press the eject button. Never press the computer’s reset button.
Getting Started Back of the computer Toshiba Equium 8100D Toshiba Equium 8100M 1-10 Equium 8100D/M Equium 8100D/M – 01CHAP.
Version 1 Last Saved on 25/sep/01 1:17 Getting Started AC power connector 1 The AC power cable plugs into the power connector. Voltage switch 2 The voltage switch changes the power supply to accept either 115V or 230V AC Power. Power switch 3 Even when the system is shut down, small electric power is used.If you don't want to spend any electric power when the system is off, power switch may be turned off. Keyboard port 4 The keyboard port connects a PS/2-compatible keyboard.
Getting Started Expansion slots 16 The expansion slot covers keep dust and dirt from entering the computer through unoccupied expansion slots. Be careful not to block the cooling vents. Also be careful to keep foreign objects out of them. A pin or similar object can damage the computer’s circuitry. Setting up the computer Setting up the computer involves connecting the various components.
Version 1 Last Saved on 25/sep/01 1:17 Getting Started Connecting peripheral devices The following sections explain how to connect your peripherals. Connecting a monitor 1. Plug the connector on the video signal cable into the blue video port on the back of the computer. 2. Firmly attach the cable by tightening the screws. Refer to your monitor documentation for more detailed instructions on connecting the monitor.
Getting Started Connecting a local printer You can connect a printer to the computer’s parallel port (burgundy), serial port (teal), or USB port, depending on the type of printer you are connecting. Check the documentation that came with your printer to determine the type of port required. Never connect the printer cable while the computer’s power is on. Doing so may damage the printer, the computer, or both.
Version 1 Last Saved on 25/sep/01 1:17 Getting Started ■ Never remove the power plug when your hands are wet. This may cause an electric shock Setting the voltage switch Computers purchased in Europe are configured for 220/240 VAC operation and should be set to 230 VAC. Computers purchased in other countries may be set to 115 VAC. The product is also designed for IT power system with phase-to-phase voltage 230V.
Getting Started Using the computer for the first time The first time you turn on the computer, your Windows operating system setup installs the devices it finds in your system. To help you get started, the operating system then guides you through several steps for completing your computer’s setup. Turning on the computer for the first time When you turn on the computer for the first time, don’t turn off the power again until the operating system has loaded completely. 1.
Version 1 Last Saved on 25/sep/01 1:17 Getting Started Restoring the preinstalled software If preinstalled software files are damaged, you will need to restore them from the Toshiba Recovery CD-ROM or the Toshiba Tools and Utilities CD-ROM. The Tools & Utilities CD-ROM and the Recovery CD-ROM are voluntary services of Toshiba. If your computer has no CD-ROM drive, both backup CD-ROMs can be run by an optional CD-ROM drive that is available from Toshiba.
Version 1 Last Saved on 13/sep/01 10:11 Learning the Basics Equium 8100D/M Chapter 2 Learning the Basics This chapter provides basic information on handling floppy disks and compact discs, and other general tasks related to computer care and usage. Precautions ■ Avoid spilling liquids onto the computer. If a liquid gets into any part of the computer, turn it off, unplug it from the AC power source, and let it dry completely before turning it on again.
Learning the Basics Computing tips ■ Save your work frequently. Your work stays in the computer’s temporary memory until you save it to disk. If the network you are using goes down and you must restart the computer to reconnect, or a power failure occurs, you may lose all the work completed since you last saved. To save your work, choose Save from the File menu of the program you are using. Some programs have an automatic-save feature which you can turn on. This feature saves your file at preset intervals.
Version 1 Last Saved on 13/sep/01 10:11 Learning the Basics Function, Ctrl and Alt keys The Function, Ctrl and Alt keys do different things depending on the program you are using. See your program documentation for details. Numeric keypad The ten-key keypad allows you to enter numbers quickly when the keyboard is in Num Lock mode (the Num Lock light is on). When the keyboard is in normal mode (the Num Lock light is off), you can use the functions shown beneath the numbers on the keys.
Learning the Basics Connecting the computer to a network Your computer has an on-board network adaptor which is ready to connect to a LAN or WAN. For specific information about connecting to the local or wide area network (LAN or WAN), consult your network administrator. When you are connected to a network, do not use the Windows Suspend or Standby command, because you may lose access to the network when you turn on the computer again.
Version 1 Last Saved on 13/sep/01 10:11 Learning the Basics To keep the computer clean, gently wipe the monitor and computer case with a slightly dampened cloth. Cover the keyboard when not in use. Moving the computer 1. Make sure all disk activity has ended (the drive-access light stops glowing). 2. If a floppy disk is in the floppy disk drive, remove it. 3. If a disc is in the CD-ROM/DVD-ROM drive, remove it and securely close the drive tray. 4.
Learning the Basics ■ To clean a compact disc that is dirty, wipe it from the centre outwards (not in a circle) with a clean dry cloth. If necessary, moisten the cloth with water or a neutral cleaner (not benzine or rubbing alcohol). Let the disc dry completely before inserting it in the drive. ■ Check all CD ROMs/DVD-ROMs before each use to ensure that they contain no cracks. Do not use CD-ROMs/DVD-ROMs that are cracked. If cracked CDs/DVDs are used in high speed drives they can be dangerous.
Version 1 Last Saved on 14/sep/01 5:29 Hardware for the Equium 8100D Equium 8100D/M Chapter 3 Hardware for the Equium 8100D This chapter provides technical information about the Equium 8100D hardware. It explains how to remove and replace the case and how to add or replace components. System components are extremely sensitive to electrostatic discharge (ESD) and require careful handling to avoid damage. When installing or removing components, always work on a flat, static-free surface.
Hardware for the Equium 8100D 3. Disconnect all cables from the computer. Failure to disconnect power, telecommunications links, networks, or modems before you open the case or start any procedure can result in personal injury or damage to equipment. Some circuitry on the motherboard may continue to operate even though the power is off. Removing the case panels In the following instructions, the directions “left” and “right” assume you are facing the back of the system unit. 1.
Version 1 Last Saved on 14/sep/01 5:29 Hardware for the Equium 8100D Removing the left panel Removing the front bezel With both case panels already removed: 1. Put your fingers in a ditch at the front bezel to pull it toward the unit front as an arrow sign shows. 2. The front bezel should separate from the cabinet easily. Removing the front bezel User's Manual 3-3 Equium 8100D/M – 03CHAP.
Hardware for the Equium 8100D Locating the internal components Removing the case panels and front bezel exposes all internal components for service. As you work inside the computer, make sure you don’t disconnect or damage other connectors, cables, or devices. Locating the internal components 1. Front expansion bays- Two 5.25-inch expansion bays enable you to fit additional devices to the front of the chassis.
Version 1 Last Saved on 14/sep/01 5:29 Hardware for the Equium 8100D Avoiding hardware conflicts Hardware devices use certain address settings and configuration values to uniquely identify them in the computer. To eliminate potential hardware conflicts when installing a new device, carefully read the installation instructions that comes with the device. Installing a new IDE device The Equium 8100D can support up to four IDE devices.
Hardware for the Equium 8100D Adding a new device 1. Shut down the computer and unplug the power cable. 2. Remove the case panels and, if necessary, the front bezel. See Opening the case. 3. Install a device to the expansion bay. When you will install the drives into the internal expansion bays, carry out the following procedures. ■ Put the shoulder screw on the part of drive where an arrow sign is indicated. Locating the shoulder screw ■ Insert the drive into the Internal expansion bay.
Version 1 Last Saved on 14/sep/01 5:29 Hardware for the Equium 8100D When you will install the drives into the front expansion bays, carry out the following procedures. ■ Insert the drive into the front expansion bay. ■ Fix the drive with two mounting screws. 4. Check the existing connections. The motherboard has two IDE connectors: a primary device connector and a secondary device connector.
Hardware for the Equium 8100D • If you are installing the device in theinternal expansion bay, fasten the new device to the chassis using four screws. 10. Connect the new device to the IDE connector. 11. Connect the new device to the power supply connector. 12. Replace the case panels and front bezel, as required. Configuring the new device Before you can use a new device, it must be configured.
Version 1 Last Saved on 14/sep/01 5:29 Hardware for the Equium 8100D Motherboard Locating the motherboard components The following components are identified in the illustration: 1. Processor- Intel® Pentium® 4 processor; speed determined by your build-to-order specification. 2. AGP expansion slot- One AGP slot provides a connection for a video expansion card. 3. PCI expansion slots- Three PCI slots provide connections from the motherboard to PCI expansion cards. 4.
Hardware for the Equium 8100D Replacing the RTC battery A lithium battery, installed on the motherboard, provides power for the real-time clock (RTC) and CMOS. The battery lasts for several years. When the battery starts to weaken and the voltage drops below a certain level, you may notice that the date and time are wrong. This is an indication that the battery needs replacing. If you replace the battery incorrectly, it can cause personal injury or damage the system.
Version 1 Last Saved on 14/sep/01 5:29 Hardware for the Equium 8100D Installing expansion cards The Equium 8100D computer has three PCI expansion slots and one AGP slot. If your computer configuration includes a modem expansion card, that card will occupy one of the PCI slots. To avoid potential hardware conflicts when installing an expansion card, carefully read the installation instructions that come with the device. IRQ setup Set an appropriate IRQ level for the expansion card.
Hardware for the Equium 8100D Adding memory Toshiba Equium 8100D/M computers are shipped with: ■ 133 MHz Synchronous DRAM (SDRAM). The main memory bank contains three 168-pin DIMM (dual inline memory module) sockets- DIMM 1, DIMM 2, and DIMM 3. The Toshiba Equium 8100D/M supports system memory from 128 MB to 1.5 GB. The memory modules available are 128 MB, 256 MB and 512 MB of SDRAM. The memory controller supports 64-bit wide DIMMs without ECC/EC.
Version 1 Last Saved on 14/sep/01 5:29 Hardware for the Equium 8100D 512 512 - - 1024 512 512 - 1536 512 512 512 Installing a DIMM The following procedure assumes you have opened the case and are observing ESD precautions. (See Opening the case.) 1. Holding the DIMM only by the edges, remove it from its antistatic package. 2. Make sure the retaining clips at either end of the socket are pushed away from the socket. 3.
Hardware for the Equium 8100D Removing a DIMM The following procedure assumes you have opened the case and are observing ESD precautions. (See Opening the case.) 1. Press the retaining clips outward (away from the DIMM) to release the DIMM. The DIMM pops up. Removing a DIMM module 2.
Version 1 Last Saved on 14/sep/01 7:01 Hardware for the Equium 8100M Equium 8100D/M Chapter 4 Hardware for the Equium 8100M This chapter provides technical information about the Equium 8100M hardware. It explains how to remove and replace the case and how to add or replace components. System components are extremely sensitive to electrostatic discharge (ESD) and require careful handling to avoid damage. When installing or removing components, always work on a flat, static-free surface.
Hardware for the Equium 8100M Before opening the case 1. Follow your operating system’s shutdown procedure to turn off the computer. 2. Unplug all computer and peripheral device power cables from the wall outlets or from your surge protector. 3. Disconnect all cables from the computer. Failure to disconnect power, telecommunications links, networks, or modems before you open the case or start any procedure can result in personal injury or damage to equipment.
Version 1 Last Saved on 14/sep/01 7:01 Hardware for the Equium 8100M Removing the left panel Removing the right panel 1. Remove the three screws that attach the right panel to the rear of the case. 2. Pull the panel toward you about an inch, then lift it up and off the machine. Removing the right panel User's Manual 4-3 Equium 8100D/M – 04chap.
Hardware for the Equium 8100M Removing the front bezel Pull the front bezel away from the cabinet, starting from the bottom. The front bezel should separate from the cabinet easily. Equium 8100M with the front bezel removed 4-4 Equium 8100D/M Equium 8100D/M – 04chap.
Version 1 Last Saved on 14/sep/01 7:01 Hardware for the Equium 8100M Locating the internal components Removing the side panels and front bezel exposes all internal components for service. As you work inside the computer, make sure you don’t disconnect or damage other connectors, cables, or devices. Locating the internal components 1. Front expansion bays- The expansion bays enable you to fit additional two 5.25-inch devices and one 3.5-inch device.
Hardware for the Equium 8100M Avoiding hardware conflicts Hardware devices use certain address settings and configuration values to uniquely identify them in the computer. To eliminate potential hardware conflicts when installing a new device, carefully read the installation instructions that comes with the device. Installing a new IDE device The Equium 8100M can support up to four IDE devices.
Version 1 Last Saved on 14/sep/01 7:01 Hardware for the Equium 8100M Adding a new device 1. Shut down the computer and unplug the power cable. 2. Remove the side panels and front bezel, as required. • To add a device to a front expansion bay, remove both side panels and the front bezel. • To add a device to an internal expansion bay, you need only remove the left side panel. For more information, see Opening the case. 3. Install a device to the internal expansion bay.
Hardware for the Equium 8100M • Secondary device connector- If your computer has a CD-ROM, DVD-ROM or CD-RW/DVD-ROM drive installed, use the extra connector on the IDE cable that is attached to the back of the CDROM/DVD-ROM drive. You will be connecting the new device to this connector. 6. Locate an available power supply connector. You will be connecting the new drive to this connector. 7. Unpack your device kit and check that it is complete.
Version 1 Last Saved on 14/sep/01 7:01 Hardware for the Equium 8100M Partitioning and formatting a new hard disk drive Before you can use the new hard disk drive, it must be partitioned and formatted. Follow the instructions provided by the manufacturer. Take care not to accidentally format your existing drive. Formatting destroys all data on a drive. User's Manual 4-9 Equium 8100D/M – 04chap.
Hardware for the Equium 8100M Motherboard The motherboard holds many of the computer’s internal components. Locating the motherboard components The following components are identified in the illustration: Processor- Intel® Pentium® 4 processor; speed determined by your build-to-order specification. AGP expansion slot- One AGP slot provides a connection for a video expansion card. PCI expansion slots- Three PCI slots provide connections from the motherboard to PCI expansion cards.
Version 1 Last Saved on 14/sep/01 7:01 Hardware for the Equium 8100M Replacing the RTC battery A lithium battery, installed on the motherboard, provides power for the real-time clock (RTC) and CMOS. The battery lasts for several years. When the battery starts to weaken and the voltage drops below a certain level, you may notice that the date and time are wrong. This is an indication that the battery needs replacing.
Hardware for the Equium 8100M Installing expansion cards The Equium 8100M computer has three PCI expansion slots and one AGP slot. If your computer configuration includes a modem expansion card, that card will occupy one of the PCI slots. To avoid potential hardware conflicts when installing an expansion card, carefully read the installation instructions that come with the device. IRQ setup Set an appropriate IRQ level for the expansion card.
Version 1 Last Saved on 14/sep/01 7:01 Hardware for the Equium 8100M Adding memory Toshiba Equium 8100D/M computers are shipped with: ■ 133 MHz Synchronous DRAM (SDRAM). The main memory bank contains three 168-pin DIMM (dual inline memory module) sockets- DIMM 1, DIMM 2, and DIMM 3. The Toshiba Equium 8100D/M supports system memory from 128 MB to 1.5 GB. The memory modules available are 128 MB, 256 MB and 512 MB of SDRAM. The memory controller supports 64-bit wide DIMMs without ECC/EC.
Hardware for the Equium 8100M 768 256 512 - 1280 256 512 512 512 512 - - 1024 512 512 - 1536 512 512 512 Installing a DIMM The following procedure assumes you have opened the case and are observing ESD precautions. (See Opening the case.) 1. Holding the DIMM only by the edges, remove it from its antistatic package. 2. Make sure the retaining clips at either end of the socket are pushed away from the socket. 3.
Version 1 Last Saved on 14/sep/01 7:01 Hardware for the Equium 8100M Removing a DIMM The following procedure assumes you have opened the case and are observing ESD precautions. (See Opening the case.) 1. Press the retaining clips outward (away from the DIMM) to release the DIMM. The DIMM pops up. Removing a DIMM module 2.
Version 1 Last Saved on 19/sep/01 2:46 If Something Goes Wrong Equium 8100D/M Chapter 5 If Something Goes Wrong This chapter provides you with hints and tips if your computer does not perform as it should. It also provides the resources you need if the problem is more serious. Some problems you may encounter when using the computer are relatively easy to identify and solve. Others may require help from your network administrator, the manufacturer of a software program, or Toshiba.
If Something Goes Wrong Defend yourself against viruses Viruses, while a potential problem, need not have a devastating effect on the computer. By taking a few, simple precautions, you can avoid infection. By making sure you have a complete backup of all your programs and data files, you can ensure a speedy recovery if you do run into problems. Problems that are easy to fix The more you work with the computer, the more likely you are to encounter the following problems.
Version 1 Last Saved on 19/sep/01 2:46 If Something Goes Wrong Your program has performed an illegal operation If you receive this message, record the details and consult the software manufacturer. To record the details: 1. Click the Details button and select (Press Ctrl and A simultaneously) the text Windows displays. 2. Press Ctrl and C simultaneously to copy the text to the clipboard. 3. Open Notepad (click Start, point to Programs, then point to Accessories and click Notepad). 4.
If Something Goes Wrong Using startup options to fix problems If Windows fails to start properly, you may have to change your system’s configuration or verify the startup procedure to fix the problem. To open the Startup Menu: 1. Restart the computer. 2. Press F8 when the computer starts. The Startup Menu displays various options. For Windows 98, these options are: ■ Normal ■ Logged (\Bootlog.
Version 1 Last Saved on 19/sep/01 2:46 If Something Goes Wrong Step-by-step confirmation With this option, the system asks you to confirm each line of the startup process. Use this option when: ■ The startup process fails while loading the startup files. ■ You need to verify that all drivers are being loaded. ■ You need to temporarily disable one or more specific driver(s). ■ You need to check for errors in the startup files.
If Something Goes Wrong Resolving a hardware conflict This section explains what to do if you receive an error message telling you there is a device driver conflict or a general hardware problem. Using Windows Help If your operating system is Windows 98/2000, try using Windows Help to troubleshoot the problem first. 1. From the Windows Help menu, click the Contents tab and select Troubleshooting. 2. Click If you have a hardware conflict and follow the steps.
Version 1 Last Saved on 19/sep/01 2:46 If Something Goes Wrong Direct Memory Access Similarly, the data required by the device are stored in a specific place or address in memory called the Direct Memory Access (DMA). The DMA provides a dedicated channel for adaptor cards to bypass the microprocessor and access memory directly. If two or more devices use the same DMA, the data required by one device overwrite the data required by the other. If this occurs, you have a hardware conflict.
If Something Goes Wrong Fixing a problem with Device Manager Device Manager provides a way to check and change the configuration of a device. Changing the default settings using Device Manager can cause other conflicts that make one or more devices unusable. Device Manager is a configuration tool for advanced users who understand configuration parameters and the ramifications of changing them. Disabling a device in Windows 1. Right-click the My Computer icon, then click Properties.
Version 1 Last Saved on 19/sep/01 2:46 If Something Goes Wrong Fixing device-related problems If you don’t have a hardware conflict, but think your problem relates to one of the computer’s devices, the first thing to do is run the Power On Self Test (POST). This test confirms that the factory-installed devices connected to the computer are working. It includes testing the memory, disk drives, display, and any additional devices you may have connected to the system.
Version 1 Last Saved on 20/sep/01 8:33 Specifications Equium 8100D/M Appendix A Specifications This appendix describes the Equium 8100D and 8100M specifications and build-to-order (BTO) options available at the time this user’s manual was published. These specifications apply to both the Equium 8100D and Equium 8100M unless otherwise stated. Processor Processor (options) Intel Pentium 4 with 256 KB level 2 cache: CPU speed depends on build to order configuration.
Specifications Hardware Chipset Intel i845 Video Graphics Controller (Options) VANTA: nVIDIA TNT2 VANTA Video Memory VANTA: 16MB SD-RAM MX200: nVIDIA GeForce2 MX-200 MX200: 32MB SD-RAM Sound support Integrated AC-97 Soft Audio. Drive bays 8100D: 4 total, 2 front accessible (5.25 inch bay), 2 x 3.5 inch internal bay. 8100M: 5 total, 3 front accessible (5.25 inch bay), 2 x 3.5 inch internal bay. CD-ROM drive (optional) 48X ATAPI-compliant EIDE CD-ROM drive or faster.
Version 1 Last Saved on 20/sep/01 8:33 Specifications Expansion card slots PCI slots 3 full-length slots total / 3available (with modem card configuration, 2 available) AGP slot 1 total / 0 available Ports Keyboard port PS/2-compatible keyboard port. Mouse port PS/2-compatible mouse port. Serial port Two 9-pin (DB-9) 16C550 UART-compatible port. USB port Four Universal Serial Bus (USB) ports support two front USB, and two rear USB peripherals without external hub.
Specifications Physical dimensions Equium 8100D Size: 17.1 in (w) x 16.1 in (d) x 5.47 in (h) 433 mm (w) x 409 mm (d) x 139 mm (h) Weight: Approx. 24.3 lbs (11.0 Kg) with CD-ROM drive Equium 8100M Size: 7.13 in (w) x 15.6 in (d) x 14.3 in (h) 181 mm (w) x 396 mm (d) x 363 mm (h) Weight: Approx. 24.9 lbs (11.
Version 1 Last Saved on 20/sep/01 8:43 Video Modes Equium 8100D/M Appendix B Video Modes This appendix lists the video modes supported by your computer’s video graphics controller. If an application you are using offers a selection of video modes that does not match those in the table for your configuration, select a mode that most closely matches your requirements.
Video Modes VANTA Refresh rate (Hz) Resolution 8-bit (256 colours) 16-bit (65,536 colours) 32-bit (True colour) 640 x 480 120 120 120 800 x 600 120 120 120 1024 x 768 120 120 120 1152 x 864 120 120 120 1280 x 1024 120 120 100 1600 x 1200 85 85 75 1920 x 1200 75 75 60 2048 x 1536 - - - The Display Modes listed above are for your reference; the actual settings may be different on your system because of using different monitor.
Version 1 Last Saved on 23/sep/01 1:13 AC Power Cord and Connectors Equium 8100D/M Appendix C AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country in which it is used. All cords must meet the following specifications: IEC60950 A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations should be considered.
AC Power Cord and Connectors Certification agencies U.S. and Canada: UL listed and CSA certified. No.18 AWG, Type SVT or SPT-2 three conductor Europe: C-2 Austria: OVE Belgium: CEBEC Denmark: DEMKO Finland: SETI France: UTE Germany: VDE Italy: IMQ The Netherlands: KEMA Norway: NEMKO Sweden: SEMKO Switzerland: SEV United Kingdom: BSI Equium 8100D/M Equium 8100D/M – C-APEND.
Version 1 Last Saved on 23/sep/01 1:13 AC Power Cord and Connectors In Europe, power cords must be HAR(harmonised) type, H05VV-F or H05VVH2-F and three conductor. For the United States and Canada, plug configuration must be a 6-15P(250V) or 5-15P(125V) as designated in the U.S. National Electrical Code Handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A and Canada, the United Kingdom, and Europe.
Version 1 Last Saved on 03/sep/01 7:23 Product Support Equium 8100D/M Appendix D Product Support If you need further assistance If you have followed the recommendations in this guide and are still having problems, you may need additional technical assistance. Before you call Since some problems may be related to the operating system or the program you’re using, it’s important to investigate other sources of assistance first.
Product Support Contact information For further assistance, you can contact Toshiba in Europe at: Toshiba Europe GmbH - Regensburg Operations Leibnizstrasse 2 D-93055 Regensburg Germany Tel: +49 (0)941 7807-888 Fax: +49 (0)941 7807-925 Austria Toshiba Europe GmbH Handelskai 388 1020 Wien Belgium Toshiba Information Systems Benelux B.V. Tel: +32-2-715-8700 Excelsiorlaan 40, B-1930 Zaventem Fax: +32-2-725-3030 http://www.toshiba.be Czech Republic CHG Service , s.r..o.
Version 1 Last Saved on 03/sep/01 7:23 Product Support Morocco C.B.I. Lotissement ATTAOUFIK, Rue No 1 Immeuble 29, Sidi Maar 20190, Casablanca Tel: +212-224371-71 Fax: +212-224371-87 Netherlands Toshiba Information Systems Benelux B.V. Tel: +31-10-2882-300 Rivium Boulevard 41 Fax: +31-10-2882-390 2909 LK Capelle a/d IJssel http://www.toshiba.nl Norway Scribona Norge A/S; Toshiba PC Service Stålfjaera 20, P.O.Box 51, Kalbakken 0901 OSLO Tel: +47-22-897-000 Fax: +47-22-897-389 http://www.toshiba.
