User’s Manual TOSHIBA Express Port Replicator II
TOSHIBA Express Port Replicator II Safety icons User’s Manual This guide contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows: DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
TOSHIBA Express Port Replicator II n Never run a power cable/cord through a pinch point such as a door or window. n Never place a power cable/cord near a heat source. n Never use nails, staples or similar objects to fasten or attach cord in place. n Never attempt to disassemble or repair an AC adaptor. Doing any of the above may damage the cables, and/or result in a fire or electric shock, possibly resulting in serious injury.
TOSHIBA Express Port Replicator II Choking hazards n Never leave small parts such as covers, caps and screws within the reach of infants or small children. Swallowing a small part may cause choking and suffocation resulting in death or serious injury. If a part is swallowed, immediately take appropriate emergency action and consult a doctor.
TOSHIBA Express Port Replicator II FCC information FCC notice "Declaration of Conformity Information" This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
TOSHIBA Express Port Replicator II Regulatory statements CE Compliance This product is CE marked in accordance with the requirements of the applicable EU Directives. Responsible for CE marking is Toshiba Europe GmbH, Hammfelddamm 8, 41460 Neuss, Germany. A copy of the official Declaration of Conformity can be obtained from following website: http://epps.toshiba-teg.com.
TOSHIBA Express Port Replicator II VCCI Class B Information Following information is only valid for EU-member States: REACH - Compliance Statement The new European Union (EU) chemical regulation, REACH (Registration, Evaluation, Authorization and Restriction of Chemicals), entered into force on 1 June 2007. Toshiba will meet all REACH requirements and is committed to provide our customers with information about the chemical substances in our products according to REACH regulation.
TOSHIBA Express Port Replicator II Copyright This guide is copyrighted by Toshiba Corporation with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein. ©2009 by Toshiba Corporation. All rights reserved. Disclaimer Information in this document is subject to change without notice.
TOSHIBA Express Port Replicator II Table of Contents Chapter 1 Introduction Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Quick Tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Chapter 2 Setting up and using the port replicator Setting up the port replicator . . . . . . . . . . . . . . .
TOSHIBA Express Port Replicator II Chapter 1 Introduction Thank you for your purchase of the TOSHIBA Express Port Replicator II. This guide tells you how to set up and begin using your TOSHIBA Express Port Replicator II and provides tips on care and troubleshooting. Package contents Carefully unpack your TOSHIBA Express Port Replicator II. Save the box and packing materials for future use.
TOSHIBA Express Port Replicator II Front view The following image illustrates the port replicator’s front and right sides. For a description of each component, please refer to the accompanying table. Hook Power button Pin Computer connector Hook Eject button Docked light Pen stand Extension Eject lever Pin Extension release Extension setting indicator (Sample Illustration) Port replicator’s front and right sides User’s Manual Component Description Power button Turns the docked computer on.
TOSHIBA Express Port Replicator II Component Description Extension Sliding component that enables the port replicator to be lengthened to fit various computer models. Extension release Releases the Extension so that it can be pulled out. Extension setting indicator Indicates the current setting of the extension. The extension can be set to 12 different positions, to accommodate various computer models. Back view The following image illustrates the port replicator’s back and left sides.
TOSHIBA Express Port Replicator II User’s Manual Component Description Front hooks Engage holes at the front of the computer to ensure a secure connection to the port replicator. Universal Serial Bus (USB) ports Connection points for USB 2.0 or 1.1 devices. Four USB ports are provided on the back of the port replicator and two on the left side. Computer lock switch In the locked position, helps prevent disconnection of the computer from the port replicator.
TOSHIBA Express Port Replicator II DC IN 15V Component Description Parallel port Connection point for a parallel printer or other parallel device. Note: For more information, see Connecting a printer to the parallel port. Serial port Connection point for a serial device. Note: You will need to install the software driver from the included CD before using the serial port for the first time. For more information, see Setting up the port replicator. DC-IN (15V) Socket for AC adaptor.
TOSHIBA Express Port Replicator II Chapter 2 Setting up and using the port replicator This chapter explains how to set up the port replicator and dock/undock your computer. Setting up the port replicator To set up the port replicator, follow the steps below: 1. Install the serial port driver that came with the port replicator. NOTE You must install the serial driver even if you are not connecting a serial device to the port replicator.
TOSHIBA Express Port Replicator II 5. Connect the included AC adaptor to the port replicator. WARNING The supplied power cord conforms to safety rules and regulations in the region where the product was purchased. Do not use the AC adaptor that was included with your computer. Always use the Toshiba AC adaptor that was provided with this product or use Toshiba recommended alternate adaptors to avoid any risk of fire and/or other damage to the computer and/or port replicator.
TOSHIBA Express Port Replicator II 7. Extend the port replicator until the extension setting indicator (shown circled in red in the accompanying illustration) points to the appropriate number for your computer model. To extend the port replicator, squeeze the extension release and pull the extension out.
TOSHIBA Express Port Replicator II Connecting a LAN cable NOTE The computer may need to be configured before connecting to a LAN. Check with your LAN administrator regarding set up procedures. To connect a LAN cable to the port replicator, follow the steps below: 1. Plug one end of the network cable into the port replicator’s network port. Gently push the cable connector in until you hear the latch click into place. (Sample Illustration) Connecting a LAN cable to the network port 2.
TOSHIBA Express Port Replicator II 3. If the computer is not already on, press the power button on the port replicator to turn the computer on. The power light on the computer will turn on, indicating that the computer is receiving power. If the computer does not turn on, please see Troubleshooting. NOTE The first time you dock your computer, a message should appear on your computer screen indicating the devices connected to the port replicator are ready to use.
TOSHIBA Express Port Replicator II 2. Press the Eject button on the port replicator. The Docked light will turn off. Eject button Docked light (Sample Illustration) Eject button on the port replicator 3. After the Docked light on the port replicator turns off, pull the Eject lever towards you while sliding the computer backwards. To avoid damaging the hooks on the port replicator, do not lift up the computer without sliding the computer backwards.
TOSHIBA Express Port Replicator II Locked position (Forward) Unlocked position (Back) Computer lock switch (Sample Illustration) Computer lock switch on the port replicator Follow these steps to secure your computer and port replicator: 1. Attach your security cable (purchased separately) to a desk or other large object, following the instructions included with your security cable. 2. Set the computer lock switch on the port replicator to the locked position. 3.
TOSHIBA Express Port Replicator II 8. If the printer came with an installation disk, click Have Disk…. Otherwise, click Next. 9. Follow the onscreen instructions to complete the installation. Installing a printer (Windows® XP) 1. 2. 3. 4. 5. 6. 7. Connect your printer to the parallel port on the port replicator. Dock your computer in the port replicator. Click Start, Control Panel. Double-click Printers and Faxes. Click Add a printer. In the Add Printer Wizard window, click Next.
TOSHIBA Express Port Replicator II NOTE When your computer is docked in the port replicator, SPDIF and Line in ports may display in Windows® audio properties dialog boxes. These ports should appear as “Currently unavailable” and are actually not provided by the port replicator. Configuring audio playback ports (Line out) in Windows Vista® 1. Right-click the speaker icon in the Notification Area of your Windows® desktop.
TOSHIBA Express Port Replicator II 3. From the Sound playback drop-down list on the Audio tab of the dialog box, select one of the following: n A Realtek High Definition Audio—to use the docked computer’s Headphone jack n A USB Multimedia Audio Device—to use the port replicator’s Line out jack 4. Click OK. 5. Connect your playback device to the port you enabled in step 3. Configuring audio recording ports (Microphone) in Windows Vista® 1.
TOSHIBA Express Port Replicator II Configuring audio recording ports (Microphone) in Windows® XP 1. Right-click the speaker icon in the system tray of your Windows® desktop. Windows® XP (Sample Image) Windows® XP speaker icon NOTE If the speaker icon is not visible in the system tray, access the audio configuration utility through the Start menu as follows: Click Start, Control Panel, Sounds, and then Audio Devices. 2. Select Adjust Audio Properties from the menu. 3.
TOSHIBA Express Port Replicator II Chapter 3 Troubleshooting This chapter provides tips to correct problems, should any occur. It also describes how to contact Toshiba should you encounter problems that you cannot resolve. Before you call Toshiba, please read the troubleshooting advice in this manual and in your computer user's manual. You may also want to consult with your system administrator or company technical support staff.
TOSHIBA Express Port Replicator II Power issues Problem Solution(s) Docked computer will not turn on (Your computer’s AC power light does not turn on) Check the connections. Make sure the power cord is firmly connected to the port replicator and a live electrical power outlet. Check the condition of the power cord and plug prongs. If the cord is frayed or damaged or the plug prongs are bent, replace the cord. If the plug prongs are soiled, wipe them with a clean cloth.
TOSHIBA Express Port Replicator II External display issues Refer also to your computer and monitor documentation. Problem Solution(s) External display does not Press hotkeys Fn + F5 to change the display turn on setting. Choose a setting that displays information to an external monitor. Refer to your computer user's manual for more information on display settings. Make sure that the monitor’s power switch is on. Confirm that the monitor’s power cable is plugged into a live electrical power outlet.
TOSHIBA Express Port Replicator II USB issues NOTE This section refers to the TOSHIBA Hardware Setup diagnostic utility. To learn how to access the TOSHIBA Hardware Setup utility, please refer to your computer user's guide. Problem Solution(s) USB device does not work Check that the cable connection between the USB ports on the port replicator and the USB device is secure. Make sure the USB device drivers are properly installed.
TOSHIBA Express Port Replicator II Hardware issues Problem Solution(s) Cannot operate the computer lock switch The computer lock switch cannot be operated when a security cable is attached to the security lock slot. Remove the security cable from the slot and then move the computer lock switch. Cannot operate the Eject Remove the security cable from the security lever lock slot, if applicable, and set the computer lock switch to the unlocked position. Then operate the Eject lever again.
TOSHIBA Express Port Replicator II Audio issues Problem Solution(s) There is no sound coming from my external audio device connected to the port replicator Check that the Mute all/Mute checkboxes in Windows® are not selected. To locate these settings, double-click the speaker icon in your Windows® system tray/Notification Area. Close your media player application, if it is running.
TOSHIBA Express Port Replicator II Problem Solution(s) When I dock my computer, the following message appears on my computer screen: Windows needs to install driver software for your USB-Serial Controller. Install the software driver provided on the CD that came with the port replicator. For more information, see step 1 in Setting up the port replicator.
TOSHIBA Express Port Replicator II Appendix A Specifications This appendix summarizes the port replicator’s technical specifications. Physical specifications Weight: 1.2 kg (2.6 lbs) Size: 322 (w) x 272 (d) x 38 (h) millimeters (12.7” (w) x 10.7” (d) x 1.
TOSHIBA Express Port Replicator II Appendix B Power Cord/Cable Connectors Your port replicator ships with the correct AC adaptor for the country of purchase. This appendix shows the shapes of the typical AC power cord/ cable connectors for various parts of the world.
TOSHIBA Express Port Replicator II Index A H AC adaptor connecting 16 specifications 16 adjusting Extension 17 hooks 11 front 13 C CAT5 CAT5 CAT5E cables 17 computer docking 18 securing 20 undocking 19 computer connector 11 computer lock switch 13, 19 configuring audio ports 22 playback ports (Line out) 23 recording ports (Microphone) 24, 25 connecting LAN cable 18 network 17 printer in Windows Vista® 21 printer in Windows® XP 22 contact information 5 D Docked light 18 E Eject button 11, 20 lever 11,
TOSHIBA Express Port Replicator II Q quick tour 10 back view 12 front view 11 S safety icons 2 instructions 2 securing computer, port replicator 20 security cable 21 lock slot 13 setting up port replicator 15 special features Wake On LAN 14 Wake Up (USB) 14 T troubleshooting audio 31 contacting Toshiba 32 other issues 31 power 27, 28, 29, 30 W Windows Vista® (Line out) 23 (Microphone) 24 Windows® XP (Line out) 23 Windowsý XP (Microphone) 25 EN-36 User’s Manual
GMAA00143E20_V04 ___
