PORTÉGÉ M400 TOSHIBA PORTÉGÉ M400 Portable Personal Computer User’s Manual
User’s Manual Copyright © 2007 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
User’s Manual FCC information Product Name : PORTÉGÉ M400 FCC notice "Declaration of Conformity Information" This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
User’s Manual EU Declaration of Conformity TOSHIBA declares, that the product: PPM40* conforms to the following Standards: Supplementary Information: “The product complies with the requirements of the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/5/EC.” This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany.
User’s Manual Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121.
User’s Manual One of the labels is located on the module.
User’s Manual Type of service Your modem is designed to be used on standard-device telephone lines. Connection to telephone company-provided coin service (central office implemented systems) is prohibited. Connection to party lines service is subject to state tariffs. If you have any questions about your telephone line, such as how many pieces of equipment you can connect to it, the telephone company will provide this information upon request.
User’s Manual Instructions for IC CS-03 certified equipment 1. The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
User’s Manual Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia. The use of other country/region setting while the modem is attached to the Australian PSTN would result in you modem being operated in a non-compliant manner.
User’s Manual ■ Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem.
User’s Manual ■ The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired. ■ It is recommended that this equipment be disconnected from the Telecom line during electrical storms.
User’s Manual Description on Laser specification The optical drive such as DVD-ROM&CD-R/RW drive and DVD Super Multi drive that is used in this computer is equipped with laser. The classification label with the following sentence is affixed to the surface of the drive.
PORTÉGÉ M400 Table of Contents Preface Manual contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxi Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xxii Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxii Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxii Keys. . . . . . . . . . . . . . . . . . . . . .
Table of Contents Front with the display open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 System indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12 Keyboard indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13 USB floppy disk drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14 Optical media drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Operating Basics Using the Touch Pad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Using the Tablet PC Pen and Reserve Pen . . . . . . . . . . . . . . . . . . . . . 4-2 Removing the Tablet PC Pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Inserting the Tablet PC Pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Pen actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Writing CDs on DVD-ROM&CD-R/RW drive . . . . . . . . . . . . . . . . . . . Before writing or rewriting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . When writing or rewriting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Writing CD/DVDs on DVD Super Multi drive. . . . . . . . . . . . . . . . . . . Important message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Legal Footnotes. . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents The Keyboard Typewriter keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Function keys: F1 … F12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Soft keys: Fn key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Emulating keys on enhanced keyboard. . . . . . . . . . . . . . . . . . . . . . . 5-2 Hot keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents HW Setup Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 HW Setup window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Configuring the Execute-Disable Bit Capability and TPM. . . . . . . . . 7-8 Starting and Ending the BIOS Setup Program . . . . . . . . . . . . . . . . . 7-8 Execute-Disable Bit Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10 LCD Display Stretch . . . . . . . .
Table of Contents Troubleshooting Problem solving process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1 Preliminary checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 Analyzing the problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 Hardware and system checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3 System start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Wireless LAN*7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Non-applicable Icons*8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Copy Protection*9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Images*10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PORTÉGÉ M400 Preface Congratulations on your purchase of the PORTÉGÉ M400 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your PORTÉGÉ M400 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Preface Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hot keys. Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes and how to set a password. Chapter 7, HW Setup, explains how to configure the computer using the HW Setup program and TPM. Chapter 8, Optional Devices, describes the optional hardware available.
Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
Preface xxiv User’s Manual
PORTÉGÉ M400 General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Instruction Manual for Safety and Comfort.
General Precautions PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time. Mobile phone Use of mobile phones can interfere with the audio system. Computer operation is not impaired but it is recommended that a distance of 30 cm be maintained between the computer and a mobile phone in use.
PORTÉGÉ M400 Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Introduction Software The following Windows® operating system and utility software are preinstalled.
Introduction Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: Processor Built-in The computer is equipped with one of the following Intel® processors. ■ Intel® CoreTM Solo Processor, which incorporates a 2MB level 2 cache memory.
Introduction Memory Slots 256, 512, 1,024 or 2,048 MB memory modules can be installed in the two memory slots for a maximum of 4,096 MB system memory. Video RAM The Video RAM capacity will differ depending on the system memory capacity in the computer. ■ If system memory is 512MB, a maximum of 64MB will be used as Video RAM. ■ If system memory is 1024MB or more, a maximum of 256MB will be used as Video RAM.
Introduction Disks Hard disk drive Available in five sizes. ■ 40.0 billion bytes (37.26 GB) ■ 60.0 billion bytes (55.89 GB) ■ 80.0 billion bytes (74.53 GB) ■ 100.0 billion bytes (93.16 GB) ■ 120.0 billion bytes (111.79 GB) Part of the space in the hard disk drive is reserved as administration space. Legal Footnote (Hard Disk Drive (HDD) Capacity)*4 For more information on the Legal Footnote regarding Hard Disk Drive (HDD) Capacity, please refer to the Legal Footnotes section in Chapter 10. Click the *4.
Introduction DVD Super Multi drive Double Layer This computer is equipped with a full-size DVD Super Multi drive module that lets you record data to rewritable CD/DVDs as well as run 12cm (4.72") or 8cm (3.15”) CD/DVDs. It reads DVDROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 24 speed, CD-RW at up to 16 speed, DVD-R and DVD+R at up to 8 speed, DVD-RW and DVD+RW at up to 4 speed, DVD-R DL at up to 2 speed, DVD+R DL at up to 2.4 speed, DVD-RAM at maximum 3 speed.
Introduction Keyboard Built-in 84 keys or 85 keys, compatible with IBM® enhanced keyboard, embedded numeric overlay, dedicated cursor control, and keys. Refer to Chapter 5, The Keyboard, for details. Pointing Device Built-in Touch Pad A Touch Pad and control buttons in the palm rest enable control of the on-screen pointer and scrolling of windows. Tablet PC Pen A pen enables data entry directly through the display screen. All models are provided with Tablet PC Pen.
Introduction Multimedia Sound system The Windows sound system compatible sound system provides output to internal speakers and microphone as well as supporting jacks for an external microphone and headphones. Headphone jack A 3.5 mm mini headphone jack enables connection of stereo headphones. Microphone jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input.
Introduction Wireless LAN Some computers in this series are equipped with a Wireless LAN card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard (Revision A, B or G). ■ Theoretical maximum speed: 54Mbps (IEEE802.11a, 802.11g) ■ Theoretical maximum speed: 11Mbps (IEEE802.11b) ■ Frequency Channel Selection (5 GHz: Revision A / 2.
Introduction Ultra Slim Bay Ultra Slim Bay Modules Ultra Slim Bay is a single-drive bay that accommodates a DVD-ROM&CD-R/RW drive, DVD Super Multi drive and secondary hard disk drive. The TOSHIBA Mobile Extension enables hot insertion of modules when you are using a plug and play operating system. Ultra Slim Bay Weight Saver To reduce weight, the Ultra Slim Bay module can be removed and a weight saver installed. It is preinstalled in some models.
Introduction User’s Manual TOSHIBA Presentation button Press this button to change internal display, simultaneous display, or multi-monitor display. The TOSHIBA Presentation button has the same functionality as the Connect display button in the Mobility Center. Pressing this button when an external display is connected will open the Windows VistaTM TMM (Transient Multimon Manager) screen.
Introduction Battery save mode *1 This feature lets you configure the computer in order to save battery power. This can be specified in the Power Options. Panel power on/off *1 This feature automatically turns power to the computer off when the display panel is closed, and turns it back on when the display panel is opened. This can be specified in the Power Options.
Introduction TOSHIBA Value Added Package This section describes the TOSHIBA Component features pre-installed on the computer. User’s Manual TOSHIBA Power Saver TOSHIBA Power Saver provides you with the features of more various power supply managements. TOSHIBA Button Support This utility controls the following computer button functions. The applications associated with each of the following buttons can be assigned by the user.
Introduction TOSHIBA Tablet PC Extension This section describes the pre-installed TOSHIBA Component features that come with the computer. To access these components, click Start -> All Programs -> TOSHIBA. TOSHIBA Rotation Utility This utility controls the screen orientation setting for both Laptop mode and Tablet mode.
Introduction TOSHIBA Wireless Key Logon This utility is intended to improve the process of logging on to BIOS/Windows by involving the additional use of a Bluetooth-ready cellular phone. DVD Video Player The DVD Video Player is used to play DVDVideo. It has an on-screen interface and functions. Click Start -> All Programs -> InterVideo WinDVD -> InterVideo WinDVD for TOSHIBA.
Introduction TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities that improve the ease and control of communication devices and network connections, help in the identification of communication problems and allow the creation of profiles if you need to switch between different locations and communication networks. To access this utility, click Start -> All Programs -> TOSHIBA -> Networking -> ConfigFree.
Introduction User’s Manual Windows Mobility Center This section describes the Windows Mobility Center. Mobility Center is a utility for accessing several mobile PC settings quickly in one window. A default maximum of eight tiles are provided by the operating system, and an additional three tiles are added to your Mobility Center. ■ Ext. Screen Orientation : This can be used to switch the orientation of an external display connected to your Tablet PC between portrait and landscape modes.
Introduction Options You can add a number of options to make your computer even more powerful and convenient to use. You can buy the following options from your reseller or TOSHIBA dealer. 1-18 Memory expansion A 256, 512, 1,024 or 2,048 MB memory module (DDR2-533/667) can easily be installed in the computer. USB FDD Kit The USB floppy disk drive accommodates either 3 1/2" 1.44-megabyte or 720-kilobyte floppy disks through connection to a USB port.
Introduction User’s Manual TOSHIBA Express Port Replicator The TOSHIBA Express Port Replicator provides the ports available on the computer in addition to a digital visual interface (DVI) port, External monitor port, Universal Serial Bus port (USB2.0) × 4, LAN jack. Tablet PC Pen Tablet PC Pen can be purchased from your TOSHIBA dealer. Use it as a spare to your computer. Spare pen tip and draw-out tool are included. Reserve Pen Reserve Pen can be purchased from your TOSHIBA dealer.
Introduction Ultra Slim Bay options The following modules can be installed in the Ultra Slim Bay. All other modules are options. 1-20 Ultra Slim Bay HDD Adaptor An adaptor lets you install an optional hard disk drive described in Chapter 8, Optional Devices. Ultra Slim Bay DVDROM & CD-R/RW Drive Kit Refer to the Features section for details. Ultra Slim Bay DVD Super Multi (Double Layer) Drive Kit Refer to the Features section for details.
PORTÉGÉ M400 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Legal Footnote (Non-applicable Icons)*8 For more information on the Legal Footnote regarding Non-applicable Icons, please refer to the Legal Footnotes section in Chapter 10. Click the *8. Front with the display closed Figure 2-1 shows the computer’s front with its LCD display panel in the closed position.
The Grand Tour ■ Turn WiFi and Bluetooth functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction of your medical device when using any WiFi or Bluetooth functionality. ■ Always turn off WiFi or Bluetooth functionality if the PC is near automatic control equipment or appliances such as automatic doors or fire detectors.
The Grand Tour Left side Figure 2-2 shows the computer’s left side. Universal Serial bus (USB 2.0) ports Cooling vents Security lock slot PC card eject button i.LINK (IEEE1394) port PC card slot Figure 2-2 The left side of the computer Cooling vents Cooling vents help CPU keep from overheating. Do not block the cooling vents. Never allow metal objects, such as screws, staples and paper clips, to enter the PC or keyboard.
The Grand Tour Keep foreign objects out of the PC card slot. Never allow metal objects, such as screws, staples and paper clips, to enter the PC or keyboard. Foreign metal objects can create a short circuit, which can cause PC damage and fire, possibly resulting in serious injury. i.LINK (IEEE1394) port This port allows you to connect an external device, such as a digital video camera for highspeed data transfer. Right side Figure 2-3 shows the computer’s right side.
The Grand Tour Bridge media slot indicator The Bridge media slot indicator glows green when the computer is accessing the SD card slot. Ultra Slim Bay A DVD-ROM&CD-R/RW drive, DVD Super Multi drive and Ultra Slim Bay HDD adaptor can be installed in the Ultra Slim Bay. Back side Figure 2-4 shows the computer’s back side.
The Grand Tour ■ Connection to any communication line other than an analog phone line could cause a PC system failure. ■ Connect the built-in modem only to ordinary analog phone lines. ■ Never connect the built-in modem to a digital line (ISDN). ■ Never connect the built-in modem to the digital connector on a public telephone or to a digital private branch exchange (PBX). ■ Never connect the built-in modem to a key telephone system for residences or offices.
The Grand Tour Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. Always make sure the display panel is closed in Laptop mode before turning the computer upside down.
The Grand Tour HDD pack cover screws Two screws secures the HDD cover. Hard disk drive This contains a Hard disk drive pack, which can be removed and reinstalled. For more information on how to remove or reinstall the HDD Kit (Serial-ATA), refer to the section on the in Chapter 8, Optional Devices. Battery pack The battery pack powers the computer when the AC adaptor is not connected. For detailed information on the battery pack, refer to Chapter 6, Power and Power-Up Modes.
The Grand Tour Front with the display open This section shows the computer with the LCD display panel open. Refer to the appropriate illustration for details. To open the display, push the display latch on the front of the LCD display panel and lift up. Position the LCD display panel at a comfortable viewing angle.
The Grand Tour 2-10 Stereo speakers The speakers emit sound generated by your software as well as audio alarms, such as low battery condition, generated by the system. Touch Pad A Touch Pad located in the center of the palm rest is used to control the on-screen pointer. Refer to the Using the Touch Pad section in Chapter 4, Operating Basics. Touch Pad control buttons Control buttons below the Touch Pad let you select menu items or manipulate text and graphics designated by the on-screen pointer.
The Grand Tour Fingerprint Sensor Just by swiping the finger against the fingerprint sensor, the following functions will be enabled: ■ Logon to Windows and access a securityenabled homepage through IE (Internet Explorer). ■ Files and folders can be encrypted/decrypted and third party access to them prevented. ■ Disable the password-protected screen-saver when returning from power-saving (Sleep) mode. ■ Power-on Security and Single Sign-on feature.
The Grand Tour System indicators LEDs beneath icons, light when various computer operations are in progress. Figure 2-7 System indicators 2-12 DC IN The DC IN indicator glows green when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange. Power The Power indicator glows green when the computer is on.
The Grand Tour Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. When the Arrow mode indicator glows the keypad overlay lets you control the cursor. When the Numeric mode indicator glows the keypad overlay lets you enter numbers. When the Caps Lock indicator glows the keyboard is in all-caps mode. Caps Lock indicator Figure 2-8 Caps Lock indicator Caps Lock This indicator glows green when the alphabet keys are locked in uppercase.
The Grand Tour USB floppy disk drive The USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks and connects to the USB port. It is supplied as standard with some models and as an option with others. USB connector Disk-In-Use Indicator Floppy disk slot Eject button Figure 2-10 USB floppy disk drive USB connector Insert this connector into one of the USB ports of your computer. Disk-In-Use Indicator This indicator lights when the floppy disk is being accessed.
The Grand Tour Optical media drives One of the following optical media drives is installed in the computer: DVDROM&CD-R/RW and DVD Super Multi drives. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. For information on loading and unloading discs refer to the Using optical media drives section in Chapter 4, Operating Basics.
The Grand Tour Formats The drives support the following formats: ■ CD-ROM ■ DVD-ROM ■ CD-DA ■ ■ ■ TM ■ Photo CD (single/multi-session) ■ ■ ■ CD-ROM XA Mode 2 (Form1, Form2) DVD -Video CD-Text CD-ROM Mode 1, Mode 2 Enhanced CD (CD-EXTRA) Addressing Method 2 DVD-ROM&CD-R/RW drive The full-size DVD-ROM&CD-R/RW drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor.
The Grand Tour AC adaptor The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost any country/region. The adaptor converts AC power to DC power and reduces the voltage supplied to this computer. To recharge the battery, simply connect the AC adaptor to a power source and the computer. Refer to Chapter 6, Power and Power-Up Modes for details.
The Grand Tour Always use the Toshiba AC adaptor that was provided with your PC and the Toshiba Battery Charger (that may have been provided with your PC), or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the PC. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the PC possibly resulting in serious injury.
PORTÉGÉ M400 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space - for your health and safety Be sure also to read Instruction Manual for Safety and Comfort. This guide, which is included with the computer, explains product liability.
Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ■ Select a work area that has: ■ a well-designed and functioning ventilation system that does not forcefully direct air on you ■ good air circulation ■ a comfortable ambient temperature and relative humidity.
Getting Started ■ Leave ample ventilation room for the fan. Do not block the vents. ■ If the PC interferes with radio equipment, turn the PC power off immediately. Such interference could cause equipment malfunction. ■ Never place your PC on a shaky table, uneven, tilted surface or other unstable location. Your PC may fall, causing damage to the PC or possibly injury. ■ Never leave the power to your PC on continuously for more than 24 hours. Turn the power off when this product is not in use.
Getting Started Seating and posture Maintain a comfortable working posture when using your PC where your body joints are naturally aligned to reduce stress on different parts of your body. Consider the following: Below eye level 90°angles Foot rest Figure 3-1 Posture and positioning of the computer ■ Keep hands, wrists, and forearms straight, in-line and roughly parallel to the floor. ■ Keep head level, or bent slightly forward, forward facing, and balanced.
Getting Started Lighting Select the right level of illumination and place your PC appropriately to minimize glare from overhead lights, desk lamps and windows. Glare on the LCD or monitor may cause eye strain, eye fatigue or headaches. Consider the following suggestions regarding lighting your work environment: ■ Position the PC so that the light source does not shine or reflect directly onto the display or shine or reflect directly into the eyes of the user.
Getting Started Strategic Rest Breaks Take short, strategically spaced rest breaks to avoid eye strain and body discomforts. For more specific recommendations on the safety and comfort of your computer environment, customers in the United States may visit the United States Department of Labor, Occupational Safety and Health Administration website at: http://www.osha.gov/SLTC/etools/ computerworkstations/ Other Things to Note ■ Never turn off the power while an application is running.
Getting Started When operating the computer in Tablet mode, follow the instructions below. Figure 3-2 Operating the computer in Tablet mode ■ Hold the computer firmly on your forearm. Do not block the vent. ■ Remove the connector of AC adaptor from the computer when using the computer in Tablet mode held in your forearm. ■ Do not use the computer while walking or driving a car. ■ Change to Laptop mode and turn off the computer before carrying. Do not carry the computer with power on or in Sleep by state.
Getting Started ■ The display panel works as a touch sensitive digitizer screen. However, the outer edges of the screen may be less sensitive. Please keep the Tablet PC Pen inside the display area when you use it near the edges of the display panel. The position of the pen may not be recognized if you move the Tablet PC Pen too fast towards the outer edge. Please be sure to slide the Tablet PC Pen slowly in areas near the edges of the screen.
Getting Started Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.
Getting Started 1. Connect the power cord to the AC adaptor. Figure 3-4 Connecting the power cord to the AC adaptor (2-pin plug) Figure 3-5 Connecting the power cord to the AC adaptor (3-pin plug) Either a 2-pin or 3-pin adaptor/cord will be included with the computer depending on the model. 2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the back of the computer. DC IN 15V jack Figure 3-6 Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet.
Getting Started Opening the display The computer’s LCD display panel can be opened in a wide range of angles for optimal viewing. 1. Push the display latch on the front of the computer to unlatch the display panel. 2. While holding down the palm rest with one hand so that the main body is not raised, lift the panel slowly. Adjust the angle of the panel to provide optimal clarity. Use reasonable care when opening and closing the LCD display panel.
Getting Started 2. Slide and hold the computer’s power button. Power button Figure 3-8 Turning on the power Starting up for the first time The Microsoft Windows VistaTM Startup Screen will be the first screen displayed when you turn on the power. Follow the on-screen instructions on each screen in order to properly install the operating system. When it is displayed, be sure to read the Software License Terms carefully.
Getting Started 4. Click the arrow button ( ( ) located in the power management buttons ) and select Shut Down from the menu. 5. Turn off any peripheral devices connected to your computer. Do not turn the computer or peripheral devices back on immediately - wait a short period to avoid any potential damage. Sleep Mode If you have to interrupt your work, you are able to turn off the power without exiting from your software by placing the computer into Sleep Mode.
Getting Started Executing Sleep Mode You can also enable Sleep Mode by pressing Fn + F3 - please refer to Chapter 5, The Keyboard, for further details. You can enter Sleep Mode in one of four ways: ■ Click Start then click the power button ( ) located in the power management buttons ( ). Please note that this feature must be enabled within the Power Options (to access it, click Start -> Control Panel -> System and Maintenance -> Power Options).
Getting Started Hibernation Mode The Hibernation Mode feature saves the contents of memory to the hard disk drive when the computer is turned off so that, the next time it is turned on, the previous state is restored. Please note that the Hibernation Mode feature does not save the status of any peripheral devices connected to the computer. ■ Save your data. While entering Hibernation Mode, the computer saves the contents of memory to the hard disk drive.
Getting Started Automatic Hibernation Mode The computer can be configured to enter Hibernation Mode automatically when you press the power button or close the lid. In order to define these settings, you can follow the steps as described below: 1. Click Start and click the Control Panel. 2. Click System and Maintenance and click Power Options. 3. Click Choose what the power buttons do or Choose what closing the lid does. 4.
Getting Started System Recovery Options About 1.5GB hidden partition is allocated on the hard disk drive for the System Recovery Options. This partition stores files which can be used to repair the system in the event of a problem. The System Recovery Options feature will be unusable if this partition is deleted. System Recovery Options The System Recovery Options feature is installed on the hard disk when shipped from the factory.
Getting Started System Recovery This section describes the creation of Recovery Discs and their use. Creating a Optical Recovery Discs This section describes how to create Recovery Discs. ■ Be sure to connect the AC adaptor when you create Recovery Discs. ■ Be sure to close all other software programs except the Recovery Disc Creator. ■ Do not run software such as screen savers which can put a heavy load on the CPU. ■ Operate the computer at full power. ■ Do not use power-saving features.
Getting Started If your optical disc drive can only write to CD's, select 'CD' as the 'Type' within the Recovery Disc Creator application otherwise, if your optical disc drive can write either CD's or DVD's, select the appropriate format based around the type of media you wish to create. Restoring the pre-installed software from the Recovery hard disk drive A portion of the total hard disk drive space is configured as a hidden recovery partition.
Getting Started 1. Load the Recovery Discs into the optical disc drive and turn off the computer's power. 2. While holding down F12 key on the keyboard, turn on your computer when the In Touch with Tomorrow TOSHIBA logo screen appears, release the F12 key. 3. Use the left and right cursors key to select the optical disc drive icon from the menu. Please refer to the Boot Priority section in Chapter 7, HW Setup for further information. 4.
PORTÉGÉ M400 Chapter 4 Operating Basics This chapter describes the basic operations of your computer and precautions when using it, as well as the handling of CD/DVD. Using the Touch Pad To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go. Touch Pad Touch Pad control buttons Figure 4-1 Touch Pad and Touch Pad control buttons Two buttons below the Touch Pad are used like the buttons on a mouse pointer.
Operating Basics You can also tap the Touch Pad to perform functions similar to those of the left button. Click: Tap once Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material. Using the Tablet PC Pen and Reserve Pen You can use the Tablet PC Pen to execute actions and enter data. Hold the Tablet PC Pen in a natural position and tap, press or trace on the screen lightly.
Operating Basics Observe the following precautions on the handling of the Tablet PC Pen. ■ Do not tap or press the Tablet PC Pen forcefully against the Display screen. It could damage the Tablet PC Pen and Display screen. ■ Avoid using or keeping the Tablet PC Pen in the place of rapid temperature change or in a car where the Tablet PC Pen is exposed to direct sunbeam. Keep the Tablet PC Pen without pressure constantly applied to the switch of the Tablet PC Pen.
Operating Basics Removing the Tablet PC Pen Remove the Tablet PC Pen as described below. 1. Gently push the Tablet PC Pen down. The pen rises up slightly. Tablet PC Pen slot Tablet PC Pen Tablet PC Pen slot Tablet PC Pen slot Figure 4-3 Removing the Tablet PC Pen 2. Pull the Tablet PC Pen to remove it from the Tablet PC Pen slot. Inserting the Tablet PC Pen The Tablet PC Pen is included in the small case coming with the product.
Operating Basics Double tap Lightly tap the tip of the Tablet PC Pen twice on an object and lift it immediately to execute an action. A double-tap is similar to double-clicking the left touch pad control button. Press and hold Touch the tip of the Tablet PC Pen to the display screen and hold it there to display a pop-up menu or other action. Press and hold is similar to clicking the right touch pad control button. Drag Touch the Tablet PC Pen to the screen.
Operating Basics Removing the Reserve Pen case To remove the Reserve Pen case, follow the steps below. 1. Save your work. 2. Turn the computer’s power off. Make sure the Power indicator is off. 3. Remove all cables connected to the computer. 4. Close the LCD display panel and turn the computer upside down. Always make sure the display panel is closed in Laptop mode before turning the computer upside down. 5. Slide and then lift out the Reserve Pen case.
Operating Basics Storing and Removing the Reserve Pen from the Reserve Pen case Follow the procedures below to remove the Reserve Pen from the Reserve Pen case. Removing the Reserve Pen from the Reserve Pen case 1. Lift the Reserve Pen up from the Reserve Pen case by its end. Reserve Pen Reserve Pen case Figure 4-8 Removing the Reserve Pen from the Reserve Pen case Storing the Reserve Pen in the Reserve Pen case 1. Insert the tip of the Reserve Pen into the Reserve Pen case holder and press down.
Operating Basics Changing to the Tablet mode To change the Laptop mode to the Tablet mode, follow the instructions below. Figure 4-10 Changing to the Tablet mode (1) ■ Place the computer on a stable, flat place such as a desktop and rotate the LCD display panel slowly, holding the panel at its lower part. The LCD display panel is designed not to rotate more than 180 degrees. Rotating the LCD display panel more than 180 degrees with an excessive force causes to damage the panel.
Operating Basics 2. Rotate the LCD display panel clockwise slowly. ■ When rotating display panel of your computer, be sure to slowly turn it in the proper direction, and not apply excessive force or speed. ■ Do not attempt to rotate the display panel past the maximum rotation point. Forcing the display panel past the maximum rotation point will damage the display panel. ■ Rotating the display panel counterclockwise will break the hinge and cause the computer to cease to function correctly.
Operating Basics 7. Press the LCD display panel downward softly.
Operating Basics ■ Execute the following applications on Primary landscape: ■ 3D game software ■ 3D screen saver ■ Playback of motion picture, such as a case of DVD-Video playback on the computer connecting an external DVD-ROM Drive. ■ The screen cannot rotate in one of the following cases.
Operating Basics Method 3: Changing the screen orientation using Task Bar 1. Right click “Change tablet and pen settings” icon in the Task Bar. Click “Change screen orientation” from the menu. The screen orientation is set to change in the following order when purchased. You can set the orientation of the desktop screen just after rotating the display from Start -> All Programs -> TOSHIBA -> Tablet PC -> Rotation Utility.
Operating Basics It is safe that you hold the computer with both hands horizontally as shown in the example. The computer is shaken horizontally. The computer is shaken perpendicularly. Figure 4-15 Shake the computer Changing to the Laptop mode To change the Tablet mode to the Laptop mode, follow the instructions below. 1. Press the Display latch and raise the display to the upright position carefully. 2. Rotate the display counter-clockwise slowly. 3.
Operating Basics How to Swipe your Finger Using the following steps when swiping fingers for fingerprint registration or authentication will help to minimize authentication failures: Align the first joint of the finger to the center of the sensor. Lightly touch the sensor and swipe finger levelly towards you when in portrait mode, and sideways when in either landscape mode or Laptop mode.
Operating Basics Points to note about the Fingerprint Sensor Please be aware of the following considerations when using the fingerprint sensor. A failure to follow these guidelines might result in damage to the sensor, sensor failure, fingerprint recognition problems or a lower fingerprint recognition success rate. ■ Do not scratch or poke the sensor with your nails or any hard or sharp objects. ■ Do not press the sensor strongly.
Operating Basics ■ Check the position and speed at which you swipe your finger across the sensor - please refer to the preceding drawing. How to Delete the Fingerprint Data Saved fingerprint data is stored in special non-volatile memory inside the fingerprint sensor. Therefore, if you give the computer to someone else, or dispose of it in any way, the following process is recommended to delete your fingerprint information: 1.
Operating Basics If both the fingerprint sensor and Trusted Platform Module (TPM) security are used as identification devices, you must install and configure the Infineon TPM Professional package first before you setup and configure the fingerprint utility. Please refer to the TPM (Trusted Platform Module) Installation Guide for further information on the installation and configuration considerations relating to TPM.
Operating Basics 7. At the User's Fingers screen, select the finger that you wish to enroll from the illustration and then click Next. On this screen please be aware that any previously enrolled fingerprints would have green check marks, while the fingerprint that you are about to enroll will have a red check mark. If any of the previously enrolled fingerprints is selected again, the latest information will be enrolled and any previous information over-written. 8.
Operating Basics ■ You must ensure that you use the TOSHIBA Password Utility to register a User Password before using the Fingerprint Power-on Security and its extended function to allow fingerprints to be used to access the computer when it is turned on.
Operating Basics Fingerprint Single Sign-on Feature General This is a feature that allows the user to complete the authentication for both the User/BIOS Password (and, if applicable, the HDD(Hard Disk Drive) Password) and logging onto Windows using only one fingerprint authentication when booting up. It is necessary to register the User/BIOS Password and Windows Logon Password before using the Fingerprint Power-on Security and this Fingerprint Single Sign-on Feature.
Operating Basics Using the USB floppy disk drive The USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks and connects to the USB port. Refer to Chapter 2, The Grand Tour, for more information. It is supplied as standard with some models and as an option with others. Connecting USB floppy disk drive To connect the drive, plug the floppy disk drive’s USB connector into a computer’s USB port. Refer to Figure 4-16.
Operating Basics Changing Ultra Slim Bay modules This section explains how to change modules in the Ultra Slim Bay. The illustrations show replacement of the optical media drive with the Ultra Slim Bay HDD adaptor. Therefore, the text refers to those modules. However, the procedures are the same for any of the modules: DVD-ROM&CD-R/ RW drive, DVD Super Multi drive and HDD adaptor. To avoid injury, do not put your hand into the Ultra Slim Bay slot.
Operating Basics 6. Grasp the optical media drive and slide it out. The optical media drive and other Ultra Slim Bay modules can become hot with use. Be careful when removing the module. Ultra Slim Bay lock screw (unlock position) Ultra Slim Bay latch Optical media drive Figure 4-18 Removing the optical media drive Inserting a module Insert the Ultra Slim Bay HDD adaptor as described below. 1. Insert the Ultra Slim Bay HDD adaptor in the computer as shown below and press until the ejector clicks. 2.
Operating Basics Using optical media drives The text and illustrations in this section refer primarily to the optical media drive. However, operations are the same for other optical drives in the Ultra Slim Bay. The full-size drive provides high-performance execution of CD/ DVD-ROM-based programs. You can run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without an adaptor. An ATAPI interface controller is used for CD/DVD-ROM operation.
Operating Basics 2. Grasp the disc tray gently and pull until it is fully opened. Disc tray Figure 4-21 Pulling the disc tray open 3. Lay the CD/DVD, label side up, in the disc tray. Laser lens Figure 4-22 Inserting a CD/DVD When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray. After seating the CD/DVD, however, make sure it lies flat, as shown in figure 4-21.
Operating Basics 5. Push the center of the disc tray to close it. Press gently until it locks into place. If the CD/DVD is not seated properly when the disc tray is closed, the CD/ DVD might be damaged. Also, the disc tray might not open fully when you press the eject button. Figure 4-23 Closing the CD/DVD disc tray Removing discs To remove the CD/DVD, follow the steps below and refer to figure 4-23. Do not press the eject button while the computer is accessing the media drive.
Operating Basics 3. Push the center of the disc tray to close it. Press gently until it locks into place. How to remove CD/DVD when the disc tray will not open Pressing the eject button will not open the disc tray when the computer power is off. If the power is off, you can open the disc tray by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button.
Operating Basics When writing to media using an optical drive, always connect the AC adaptor to a power plug socket. If data is written while powered by the batteries, writing may sometimes fail due to low battery power and data loss may occur. Before writing or rewriting Please observe the following points when you write or rewrite the data. ■ We recommend the following manufacturers of CD-R and CD-RW media. Media quality can affect write or rewrite success rates. CD-R: TAIYO YUDEN CO., LTD.
Operating Basics When writing or rewriting Note the following when you write or rewrite a CD-R or CD-RW. ■ Always copy data from the hard disk drive to the optical media. Do not use cut-and-paste as the original data will be lost if there is a write error. ■ Do not perform any of the following actions: ■ ■ ■ ■ ■ Change users in the Windows VistaTM operating system. ■ Operate the computer for any other function, including use of a mouse or Touch Pad, closing/opening the LCD panel.
Operating Basics Important message Before you write or rewrite to CD-R/RW or DVD-R/-R DL/-RW/+R/+R DL/ +RW/-RAM discs, read and follow all setup and operating instructions in this section. If you fail to do so, the DVD Super Multi drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage.
Operating Basics DVD-R: DVD Specifications for Recordable Disc for General Version 2.0 TAIYO YUDEN CO., LTD. Matsushita Electric Industrial Co., Ltd. DVD-R (Dual Layer): MITSUBISHI CHEMICAL CORPORATION DVD+R: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD+R DL: MITSUBISHI CHEMICAL CORPORATION DVD-RW: DVD Specifications for Recordable Disc for Version 1.1 or version 1.2 VICTOR COMPANY OF JAPAN.LIMITED MITSUBISHI CHEMICAL CORPORATION DVD+RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd.
Operating Basics ■ DISC created in DVD-R DL format4 (Layer Jump Recording) cannot be read. ■ There are two types of DVD-R discs: authoring and general use discs. Do not use authoring discs. Only general use discs can be written to by a computer drive. ■ You can use DVD-RAM discs that can be removed from a cartridge and DVD-RAM discs designed without a cartridge. ■ Other DVD-ROM drives for computers or other DVD players may not be able to read DVD-R/-R DL/-RW or DVD+R/+R DL/+RW discs.
Operating Basics When writing or rewriting Please observe/consider the following when you write or rewrite to a CD-R/ RW, DVD-R/-R DL/-RW/-RAM or DVD+R/+R DL/+RW disc. ■ Do not perform any of the following actions when writing or rewriting: ■ ■ ■ ■ ■ ■ Change users in the Windows VistaTM operating system. ■ Operate the computer for any other function, including using a mouse or Touch Pad or closing/opening the LCD panel. ■ Start a communication application such as a modem.
Operating Basics ■ You cannot back up DVD-ROM, DVD-Video, DVD-R/-R DL/-RW or DVD+R/+R DL/+RW to CD-R/RW using the “Disk Backup” function of TOSHIBA Disc Creator. ■ TOSHIBA Disc Creator cannot record in packet format. ■ You might not be able to use the “Disk Backup” function of TOSHIBA Disc Creator to back up a DVD-R/-R DL/-RW or DVD+R/+R DL/+RW disc that was made with other software on a different DVD-R/-R DL/RW or DVD+R/+R DL/+RW recorder.
Operating Basics When Using Ulead DVD MovieFactory® for TOSHIBA How to make a DVD-Video Simplified steps for making a DVD-Video from video data captured from a DV-Camcorder: 1. Click Start -> All Programs -> DVD MovieFactory for TOSHIBA -> Ulead DVD MovieFactory for TOSHIBA Launcher to launch DVD MovieFactory. 2. Insert a DVD-RW or DVD+RW disc in Burner. 3. Click Video Disc -> Burn Video to Disc to launch Direct Recording dialog box ,choose DVD-Video/+VR to invoke Straight Capture to Disc Page. 4.
Operating Basics ■ Do not enter Sleep or Hibernation Mode while using DVD MovieFactory. ■ Do not operate DVD MovieFactory immediately after turning on the computer. Please wait until all Disc Drive activity has stopped. ■ When recording to a DV-Camcorder, to ensure you capture all of your data, let the camcorder record for a few seconds before you begin recording your actual data. ■ CD recorder, JPEG functions, DVD-Audio, mini DVD and Video CD functions are not supported in this version.
Operating Basics Media care This section provides tips on protecting data stored on your CD/DVDs and floppy disks. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1. Store your CD/DVDs in the container they came in to protect them and keep them clean. 2. Do not bend the CD/DVD. 3. Do not write on, apply a sticker to, or otherwise mar the surface of the CD/DVD that contains data. 4.
Operating Basics 8. Do not eat, smoke, or use erasers near your floppy disks. Foreign particles inside the floppy disk’s jacket can damage the magnetic surface. 9. Magnetic energy can destroy the data on your floppy disks. Keep your floppy disks away from speakers, radios, television sets and other sources of magnetic fields. Sound System This section describes some of the audio control functions.
Operating Basics TOSHIBA Mic Effect TOSHIBA Mic Effect provides you with a hands-free environment for holding mutual communication via the Internet Protocol or Local Area Network. If you wish to communicate with someone on your computer, you can use a messenger application. However, with such an application, you would hear your own voice returning to you as echo during the communication if you did not use a headset system or headphone. TOSHIBA Mic Effect will reduce these echoes generated on your computer.
Operating Basics Modem This section describes how to connect and disconnect the internal modem to and from a telephone jack. ■ Connection to any communication line other than an analog phone line could cause a PC system failure. ■ Connect the built-in modem only to ordinary analog phone lines. ■ Never connect the built-in modem to a digital line (ISDN). ■ Never connect the built-in modem to the digital connector on a public telephone or to a digital private branch exchange (PBX).
Operating Basics Properties menu Click the icon with the secondary mouse button to display properties menu on the screen. Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection.
Operating Basics Connecting To connect the modular cable, follow the steps below. The modular cable that comes with the computer must be used to connect the modem. Connect the end of the modular cable with the core to the computer. ■ Connection to any communication line other than an analog phone line could cause a PC system failure. ■ Connect the built-in modem only to ordinary analog phone lines. ■ Never connect the built-in modem to a digital line (ISDN).
Operating Basics Disconnecting To disconnect the internal modular cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. Disconnect the cable from the computer’s modem jack in the same manner. Wireless communications The computer’s wireless communication function supports both Wireless LAN and Bluetooth devices. All models are provided with Wireless Communication switch.
Operating Basics ■ The values shown above are the theoretical maximums for Wireless LAN standards. The actual values may differ. ■ The transmission speed over the wireless LAN, and the distance over which the wireless LAN can reach, may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, client design and software/hardware configurations.
Operating Basics Radio links You can easily establish links between two or more devices, with these links being maintained even if the devices are not within a line-of-sight of each other. Security Two advanced security mechanisms ensure a high level of security: ■ Authentication prevents access to critical data and makes it impossible to falsify the origin of a message. ■ Encryption prevents eavesdropping and maintains link privacy.
Operating Basics Wireless communication switch You can enable or disable Wireless LAN and Bluetooth functions, with the on/off switch. No transmissions are sent or received when the switch is off. Slide the switch to the right to turn it on and to the left to turn it off. ■ Do not use the WiFi or Bluetooth functionalities near a microwave oven or in areas subject to radio interference or magnetic fields. Interference from a microwave oven or other source can disrupt WiFi or Bluetooth operation.
Operating Basics LAN The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). This section describes how to connect/disconnect to a LAN. Do not install or remove an optional memory module while Wake-up on LAN is enabled. The Wake-up on LAN function consumes power even when the system is off. Leave the AC adaptor connected while using this feature.
Operating Basics 1. Turn off the power to the computer and to all external devices connected to the computer. 2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place. LAN jack LAN connector Figure 4-27 Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. When the computer is exchanging data with the LAN, the LAN Active indicator glows orange.
Operating Basics Moving the computer The computer is designed for rugged durability. However, a few simple precautions taken when moving the computer will help ensure trouble-free operation. ■ Before moving the computer, it recommends changing the function of TOSHIBA HDD Protection. Refer to the section, Using the Hard Disk Drive (HDD) Protection, in this chapter. ■ Make sure all disk activity has ended before moving the computer. Check the HDD indicator on the computer.
Operating Basics When vibration is detected, a message will be displayed on the screen, and the icon in the taskbar notification area will change to the protection state. This message is displayed until the OK button is pressed or 30 seconds pass. When vibration subsides, the icon returns to the normal state. Taskbar Icon State Icon Description Normal TOSHIBA HDD Protection is enabled. Protection TOSHIBA HDD Protection is active. The hard disk drive head is in a safe position.
Operating Basics 3D Viewer This feature displays a 3D object on the screen which moves in according to tilting or vibration of the computer. When the TOSHIBA HDD Protection detects computer vibration the Hard Disk Drive head is parked and the 3D object disk rotation will stop. When the head is un-parked the disk will begin to rotate again. The 3D Viewer can be started from the icon in the task tray. ■ This 3D object virtually represents the Computer's internal Hard Disk Drive.
Operating Basics Heat dispersal To protect against overheating, the processor is equipped an internal temperature sensor which activates a cooling fan or lowers the processing speed if the computer's internal temperature rises to a certain level.
PORTÉGÉ M400 Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available.
The Keyboard Function keys: F1 … F12 The function keys (not to be confused with Fn) are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. Refer to the section, Soft keys: Fn key combinations, in this chapter.
The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to the Keypad overlay section in this chapter for more information on how to operate these keys. The power on default for both settings is off. Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off.
The Keyboard Power Plan: Pressing Fn + F2 changes the power settings. Sleep: Pressing Fn + F3 switches the system to Sleep mode. Hibernate: Pressing Fn + F4 switches the system to Hibernate mode. Output: Pressing Fn + F5 changes the active display device. Brightness (Down): Pressing Fn + F6 decreases the computer's display panel brightness in individual steps. Brightness (Up): Pressing Fn + F7 increases the computer's display panel brightness in individual steps.
The Keyboard Touch Pad: Pressing Fn + F9 enables or disables the Touch Pad function. Zoom: Pressing Fn + Space changes the display resolution. ODD : Pressing Fn + Tab turns the power of the optical media drive on/off or ejects the disc tray. TOSHIBA Zooming Utility (reduce): Pressing Fn + 1 reduces the icon size on the desktop or the font sizes within one of the supported application windows.
The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows: Windows Start Button activates the Start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows Start menu. This key has the same function as the secondary mouse button. Keypad overlay Your computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one.
The Keyboard Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in figure 5-2. Press Fn + F11 again to turn off the overlay. Figure 5-2 The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off. 2.
The Keyboard Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key. If the computer is in Arrow mode, you can switch temporarily to Numeric mode by pressing a shift key. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes. With the overlay on: 1. Hold down Alt. 2. Using the overlay keys, type the ASCII code. 3.
PORTÉGÉ M400 Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Power and Power-Up Modes Table 6-1 Power conditions continued AC adaptor connected Power on Power off (no operation) Secondary battery fully charged • Operates • No charge • LED: Secondary battery green DC IN green • No charge • LED: Secondary battery green DC IN green Secondary battery partially charged or no charge • Operates • Charge*2 • LED: Secondary battery orange DC IN green • Quick charge*2 • LED: Secondary battery orange DC IN green No Secondary • Operates battery installed • No charge •
Power and Power-Up Modes Power on AC adaptor not connected Secondary battery charge is above low battery trigger point • Operates • LED: Secondary battery off DC IN off Secondary battery charge is below low battery trigger point • Operates • LED: Secondary battery flashes orange DC IN off Secondary battery charge is exhausted Computer shuts down *3 No Secondary battery is installed • No operation *5 • LED: Secondary battery off DC IN off Power off (no operation) *1 When the Slice Expansion batter
Power and Power-Up Modes Power indicators As shown in the above table, the Battery, Secondary battery, DC IN and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicator Check the Battery indicator to determine the status of the main battery and the Secondary battery indicator to determine the status of the Slice Expansion battery.
Power and Power-Up Modes Power indicator Check the Power indicator to determine the power status: Green Indicates power is being supplied to the computer and the computer is turned on. Flashing orange Indicates power is being supplied to the computer while the computer is in Sleep Mode. The indicator turns on for one second and off for two seconds. No light Under any other conditions, the indicator does not light.
Power and Power-Up Modes ■ Do not remove the battery pack while the computer is in Sleep Mode. Data is stored in RAM, so if the computer loses power it will be lost. When the computer is powered off in Sleep Mode, and the AC adaptor is not connected, the battery pack supplies power to maintain data and programs in memory. If the battery pack is completely discharged, Sleep Mode will not function and the computer loses all data in memory.
Power and Power-Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance. Safety precautions Mishandling of battery packs can cause death, serious injury or property damage.
Power and Power-Up Modes 8. Never store a battery pack in an area of high humidity. This could cause a fire or explosion possibly resulting in serious injury. 9. Never expose a battery pack to abnormal shock, vibration or pressure. The battery pack's internal protective device could fail, causing it to overheat or ignite resulting in caustic liquid leakage, or explosion or fire, possibly resulting in death or serious injury. 10.
Power and Power-Up Modes 15. Make sure the battery is securely installed in the computer before attempting to charge the battery pack. Improper installation could generate smoke or fire, or cause the battery pack to rupture. 16. Keep the battery pack out of reach of infants and children. It can cause injury. Caution 1. Use only battery packs recommended by TOSHIBA as replacements. 2.
Power and Power-Up Modes Charging the batteries When the power in the battery pack becomes low, the Battery indicator will flash orange to indicate that only a few minutes of battery power remain. If you continue to use the computer while the Battery indicator flashes, the computer will enable Hibernation Mode so that you do not lose any data, and automatically turn itself off. You must recharge a battery pack when it becomes discharged.
Power and Power-Up Modes The Battery indicator may show a rapid decrease in battery operating time when you try to charge a battery under the following conditions: ■ The battery has not been used for a long time. ■ The battery has completely discharged and been left in the computer for a long time. ■ A cool battery is installed in a warm computer. In such case, follow the steps below. 1. Fully discharge the battery by leaving it in the computer with the power on until the power automatically shuts off. 2.
Power and Power-Up Modes Maximizing battery operating time A battery’s usefulness depends on how long it can supply power on a single charge. How long the charge lasts in a battery depends on: ■ CPU Processing speed ■ Screen brightness ■ System Sleep ■ System Hibernation ■ Monitor Power off ■ HDD Power off ■ How often and how long you use the hard disk, optical disc and the floppy disk drive. ■ How much charge the battery contained to begin with.
Power and Power-Up Modes Extending battery life To maximize the life of your battery pack: ■ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below. 1. Turn off the computer’s power. 2. Disconnect the AC adaptor and turn on the computer’s power. If it does not turn on go to step 4. 3. Operate the computer on battery power for five minutes.
Power and Power-Up Modes 1. 2. 3. 4. Save your work. Turn the computer’s power off. Make sure the Power indicator is off. Remove all cables connected to the computer. Close the LCD display panel and turn the computer upside down. Always make sure the display panel is closed in Laptop mode before turning the computer upside down. 5. Slide the battery safety lock towards the release ( the battery release latch movable.
Power and Power-Up Modes 7. Insert the battery pack (➀). 8. Make sure that the battery pack is securely in place and the battery safety lock (➁) is in the lock position ( ). Battery pack Battery lock Figure 6-3 Securing the battery pack 9. Turn your computer over. TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set by the TOSHIBA Password Utility function are different from the Windows password.
Power and Power-Up Modes ■ After you set the password, a dialog box will be displayed asking whether you want to save it to a floppy diskette or other media. If you forget the password, you can open the password file on another computer. Be sure to keep the media in a safe place. ■ When entering the character string to register the password, enter from the keyboard character by character and do not enter as ASCII code or copy-and-paste the character string.
Power and Power-Up Modes User Token field ■ Create (button) You can use an SD card token, instead of entering the password. After you have registered a password, insert an SD card in SD card slot and click Create. You can use an SD card of any capacity, but it must be formatted correctly. If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format.
Power and Power-Up Modes Starting the computer by password If you have already registered a password, there are three ways to start the computer: ■ Insert an SD card token before you turn on the computer. The computer will start normally, without displaying a password prompt. ■ Swipe your fingerprint on the sensor if you have already registered the fingerprint with the Fingerprint utility and enabled Fingerprint System Boot Authentication.
Power and Power-Up Modes Tablet mode Enter your password by tapping the on-screen keyboard using the Tablet PC Pen. Figure 6-4 On-screen keyboard ■ The beep sounds when tapping the on-screen keyboard with the Tablet PC Pen. An * (asterisk) is displayed after “Password =” and one character is input for every tapping. Register your password to the computer in the Laptop mode using the standard keyboard. Refer to TOSHIBA Password Utility, in this chapter for the detail.
Power and Power-Up Modes Panel power on/off You can set up your computer so that power turns off automatically when you close the display panel. When you open the panel, power will be turned on in Sleep Mode or Hibernation Mode but not in boot mode. If the panel power off function is enabled and you manually shut down Windows, do not close the computer’s LCD display panel until the shut down process has been completed.
PORTÉGÉ M400 Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer, and provides information on setting up the Execute-Disable Bit Capability and TPM. Accessing HW Setup To run the HW Setup program, click Start -> All Programs -> TOSHIBA -> Utilities -> HWSetup. HW Setup window The HW Setup window contains the following tabs: General, Display, Boot Priority, Keyboard, CPU, LAN, Device Config and USB. There are also three buttons: OK, Cancel and Apply.
HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor.
HW Setup Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: HDD −> FDD −> CDROM −> LAN The computer looks for bootable files in the following order: HDD, floppy disk drive*1, CDROM*2 and LAN (Default). FDD −> HDD −> CDROM −> LAN The computer looks for bootable files in the following order: floppy disk drive*1, HDD, CDROM*2 and LAN.
HW Setup To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, Ultra Slim Bay HDD, CD-ROM, FDD (or SD memory card), Network (LAN), USB Memory boot. A bar will appear only under the selected device. 3. Use the left/right cursor keys to highlight the boot device you want and press Enter.
HW Setup HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. Built-in HDD 1 -> Built-in HDD 2 -> USB (Default) The priority is set as Built-in HDD 1 -> Built-in HDD 2 -> USB. Built-in HDD 2 -> Built-in HDD 1 -> USB The priority is set as Built-in HDD 2 -> Built-in HDD 1 -> USB.
HW Setup USB Memory BIOS Support Type Set the type of the USB memory as a startup device. HDD Set the type of the USB memory to be equivalent to the HDD (Default). * Based on the [HDD] order in the [Boot Priority Options] item. The order with respect to the other HDD can be set in the [HDD Priority Options] item. FDD Set the type of the USB memory to be equivalent to the FDD. * Based on the [FDD] order in the [Boot Priority Options] item.
HW Setup LAN Wake-up on LAN This feature lets the computer’s power be turned on when it receives a wake-up signal from the LAN. Enabled Enables Wake-up on LAN. Disabled Disables Wake-up on LAN (Default). Do not install or remove an optional memory module while Wake-up on LAN is enabled. The Wake-up on LAN function consumes power even when the system is off. Leave the AC adaptor connected while using this feature. Built-in LAN This feature enables or disables the Built-in LAN.
HW Setup USB-FDD Legacy Emulation Use this option to enable or disable USB floppy disk drive legacy emulation. If your operating system does not support USB, you can still use a USB floppy disk drive by setting the USB-FDD Legacy Emulation item to Enabled. Enabled Enables the USB floppy disk drive legacy emulation function (Default). Disabled Disables the USB floppy disk drive legacy emulation function.
HW Setup Select either the Execute-Disable Bit Capability or settings in the security controller to make changes. Please refer to the operating instructions displayed in the settings screen. Ending the BIOS Setup Program Save the changes and end the program. 1. Press the End Key. The “Are you sure? (Y/N) The changes you made will cause the system to reboot.” message is displayed. 2. Press the Y key. The configured settings are saved and the BIOS setup program ends.
HW Setup Enhanced C-States This feature enables or disables the Enhanced C-States. Enabled This lowers the power consumption (Default). Disabled This does not lower the power consumption. Execute-Disable Bit Capability This setting, which is displayed on the first page of the setup screen, configures the Execute-Disable Bit function of the CPU.
HW Setup Clear TPM Owner This setting is used to erase the data in TPM when disposing of the computer or when the owner of the computer changes, etc. Once this operation is carried out, the TPM configuration settings are erased, such that the encrypted data can no longer be decrypted and the files can no longer be read. Please backup or delete the data as necessary before carrying out this operation. The operating procedure is as follows: 1.
HW Setup 7-12 User’s Manual
PORTÉGÉ M400 Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility.
Optional Devices PC card The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission. PC cards can sometimes become hot during PC operation.
Optional Devices Removing a PC card To remove the PC card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to PC card and click. 3. Press the PC card eject button to extend it. If the PC card is not inserted all the way, the eject button may not cause it to pop out sufficiently to allows it to be grasped. Be sure to push the PC card firmly into the computer and slide the eject button again. 4. Press the extended eject button to pop the card out slightly. 5.
Optional Devices Media care Observe the following precautions when handling the card. Card care ■ Do not twist or bend cards. ■ Do not expose cards to liquids or store in humid areas or lay media close to containers of liquid. ■ Do not touch the metal part of a card or expose it to liquids or let it get dirty. ■ After using card, return it to its case. ■ The card is designed so that it can be inserted only one way. Do not try to force the card into the slot.
Optional Devices 2. Press gently to ensure a firm connection. SD card Bridge media slot Figure 8-3 Inserting an SD card ■ Make sure the SD card is oriented properly before you insert it. ■ Do not turn the computer off or switch to Sleep Mode or Hibernate Mode while files are being copied - doing so may cause data to be lost. Removing an SD card To remove an SD card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to SD card and click. 3.
Optional Devices SD memory card SD cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD card flash-memory. The cards have a high level of security and copy protection features. SD memory cards comply with SDMI (Secure Digital Music Initiative), which is a technology adopted to prevent unlawful copy or playback of digital music. For this reason, you cannot copy or playback protected material on another computer or other device.
Optional Devices Inserting a Memory Stick To insert a Memory Stick, follow the steps below. 1. Insert the Memory Stick into the Bridge media slot. 2. Press gently to ensure a firm connection. Bridge media slot indicator Bridge media slot Memory Stick Figure 8-5 Inserting a Memory Stick Removing a Memory Stick To remove a Memory Stick, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to Memory Stick and click. 3.
Optional Devices xD picture card The computer is equipped with a Bridge media slot that can accommodate xD picture cards with various memory capacities. The xD picture card let you easily transfer data from devices, such as digital cameras that use xD picture card flash-memory. Keep foreign objects out of the Bridge media slot. Never allow metal objects, such as screws, staples and paper clips, to enter the PC or keyboard.
Optional Devices Memory expansion You can install additional memory in the computer’s memory module slot to increase the amount of RAM. This section describes how to install and remove a memory module. ■ Place a mat beneath the computer to prevent scratching or damaging the computer's lid when installing/replacing the memory module. Avoid mats made of materials that generate static electricity.
Optional Devices Installing memory module There are slots for two memory modules. The procedures are the same for installing either module. 1. Set the computer to boot mode and turn the computer’s power off. Make sure the Power indicator is off. Refer to the Turning off the power section in Chapter 3, Getting Started. 2. Remove AC adaptor and all cables connected to the computer. 3. Turn the computer upside down and remove the battery pack.
Optional Devices 8. Lift the top edge of the keyboard after sliding the two release latches and lay in face down on the palm rest. ■ When you move the keyboard forward, do not touch the keys. Doing so could cause misalignment. Hold the keyboard by the sides and lay it gently on the palm rest. ■ The keyboard is connected to the computer by a keyboard ribbon cable. Be careful not to apply tension to this cable when you lift up the keyboard. Do not try to disconnect this cable.
Optional Devices 10. Fit the memory module's connectors into the socket at about a 45 degree angle and push the module down until latches on either side snap into place. Align the notch of the memory module with that of the memory slot and gently insert the module into the slot. Slot A Slot B Figure 8-10 Installing the memory module 11. Screw in the two screws and replace the memory module cover. Screws Memory module cover Figure 8-11 Seating the memory module cover 12.
Optional Devices Do not bend the keyboard ribbon cable. 13. Insert the tabs on the front of the keyboard into the corresponding notches on the computer and lower the keyboard into place after ensuring the two release latches click into place. When seating the keyboard, be sure to connect the circuit board if the keyboard ribbon cable was pulled out while you were removing the keyboard. 14. Screw the two screws and secure the keyboard. Be sure to use all two screws removed in step 7.
Optional Devices 6. Grasp the sides of the module and pull it out. ■ If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Or you will get burnt if you touch any of them. ■ Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. Latches Figure 8-13 Removing the memory module 7.
Optional Devices Slice Expansion Battery This battery pack increases your computer's operating time when a main battery pack is also installed. For details on using the battery pack, follow the steps below. Connecting the Slice Expansion Battery Follow the steps below to connect the Slice Expansion Battery to the computer When handling Slice Expansion Battery, be careful not to short circuit the terminals.
Optional Devices 5. Close the latches to secure the Slice Expansion Battery to the computer. Figure 8-15 Securing the latches Disconnecting the Slice Expansion Battery Follow the steps below to disconnect the Slice Expansion Battery to the computer. 1. Save your work. 2. Turn the computer’s power off. Make sure the Power indicator is off. 3. Remove all cables connected to the computer. 4. Lay the computer upside down. 5. Open the release latches in the direction of the arrows.
Optional Devices 6. Lift off the Slice Expansion Battery. Figure 8-17 Removing the Slice Expansion Battery 7. Be sure to replace the protective cap before storing the Slice Expansion Battery. Battery Charger The battery charger provides a convenient way to charge battery packs without requiring the use of your computer. The battery charger holds up to two battery packs (lithium ion).
Optional Devices 5. A small row of ridges marks the latches securing the cover. Press on these ridges until you hear a click. 6. Press on the arrows and lift the cover up and out to remove it. Screws Hard disk drive cover Figure 8-18 Removing the hard disk drive cover 7. Reposition the hard disk drive until it is vertical. 8. With the hard disk drive in a vertical position, lift it straight up and away from the connector.
Optional Devices 4. With the connector connected, lower the hard disk drive down to the storage position. Connector Plastic tab Hard disk drive pack Figure 8-20 Installing the hard disk drive pack 5. Seat the cover and press down until the latches click into place. 6. Secure the cover with two screws. 7. Turn your computer over. Ultra Slim Bay HDD Adaptor You can increase your computer’s data storage capacity by installing an additional 80.0 billion bytes (74.53 GB) and 100.0 billion bytes (93.
Optional Devices 2. Insert the hard disk drive in the Ultra Slim Bay HDD adaptor and push forward to ensure a firm connection. Tuck the Plastic tab underneath the hard disk drive. Hard disk drive Figure 8-22 Inserting the hard disk drive 3. Close the lid and slide the lock to the lock position. Lid Figure 8-23 Closing the lid For details on inserting the Ultra Slim Bay HDD adaptor in the computer’s Ultra Slim Bay slot, refer to Chapter 4, Operating Basics.
Optional Devices Tablet PC Pen Use it as a spare to your computer. Spare pen tip and draw-out tool are included. Refer to Chapter 6, Power and Power-Up Modes, for the detailed usage. Reserve Pen Use the Reserve Pen in place of the Tablet PC Pen if the Tablet PC Pen is lost or broken. Refer to Chapter 6, Power and Power-Up Modes, for the detailed usage. External monitor An external analog monitor can be connected to the external monitor port on the computer.
Optional Devices i.LINK (IEEE1394) i.LINK (IEEE1394) is used for high-speed data transfer for a range of compatible devices such as ■ Digital video cameras ■ Hard disk drives ■ MO drives ■ Writable optical disc drives i.LINK uses a four-pin connector, which does not carry any electric current. External devices will need their own power supply to operate. Precautions ■ Make a back-up of your data before transferring it to the computer. There is a possibility that the original data will be damaged.
Optional Devices Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. i.LINK (IEEE1394) port i.LINK (IEEE1394) connector Figure 8-25 Connecting the i.LINK (IEEE1394) cable into the computer 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■ You may need to install drivers for your i.LINK devices. ■ Not all i.LINK devices have been tested. Therefore, compatibility with all i.
Optional Devices TOSHIBA Express Port Replicator In addition to the ports available on the computer, the TOSHIBA Express Port Replicator. The TOSHIBA Express Port Replicator connects directly to the docking interface on the underside of the computer. The AC adaptor connects the TOSHIBA Express Port Replicator to a power source. The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation.
Optional Devices Security lock Security locks enable you to anchor your computer and optional TOSHIBA Express Port Replicator to a desk or other heavy object to help prevent unauthorized removal of the computer or TOSHIBA Express Port Replicator. The computer has a security lock slot on the left side. Attach one end of a cable to a desk and the other end to the security lock slot. 1. Turn the computer so the left side faces you. 2. Align the holes for the security lock and attach the lock.
Optional Devices 8-26 User’s Manual
PORTÉGÉ M400 Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists.
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer and any other external device you are using. ■ Before you attach an external device, turn the computer off. When you turn the computer back on it recognizes the new device.
Troubleshooting Software Hardware The problems may be caused by your software or disk. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation. These documents usually include a problem solving section or a summary of error messages. Next, check any error messages in the operating system documentation.
Troubleshooting Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: S In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program.
Troubleshooting If the computer has reached room temperature and still does not start, or if it starts but shuts down quickly contact your dealer. Computer shuts down and its DC IN indicator is flashing green Indicates a problem with the heat dispersal system. Please contact your dealer. AC power If you have trouble turning on the computer with the AC adaptor connected, check the DC IN indicator. Refer to Chapter 6, Power and Power-Up Modes for more information.
Troubleshooting Problem Procedure Battery doesn’t charge when the AC adaptor is attached (Battery or Ultra Slim Bay indicator does not glow orange.) If the battery is completely discharged, it will not begin charging immediately. Wait a few minutes. If the battery still does not charge, make sure the outlet of the AC adaptor is supplying power. Test it by plugging in an appliance. Check whether the battery is hot or cold to the touch. If the battery is too hot or too cold, it will not charge properly.
Troubleshooting Real Time Clock Problem Procedure The following message is Displayed on the LCD screen: RTC battery is low or CMOS checksum is inconsistent. Press [F1] key to set Date/Time. The charge in the RTC battery has run out - you will need to set the date and time in the BIOS setup using the following steps: 1. Press F1 key. BIOS setup will boot up. 2. Set the date in System Date. 3. Set the time in System Time. 4. Press End key. Confirmation message will appear. 5. Press Y key.
Troubleshooting Internal LCD display panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, HW Setup, for more information. Problem Procedure No display Press hotkeys Fn + F5 to change the display priority, to make sure it is not set for an external monitor. Markings appear on the The marks may have come from contact with the LCD screen. keyboard or Touch Pad. Try wiping the LCD screen gently with a clean dry cloth.
Troubleshooting DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s disc tray is securely closed. Press gently until it clicks into place. Check whether the drive power is on. If the power is off, press the Fn + tab keys simultaneously and turn on the power. Open the disc tray and make sure the CD/DVD is properly seated. It should lie flat with the label facing up.
Troubleshooting Problem Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording. ■ Do not run or start other software during writing. ■ Do not jar the computer during writing. ■ Do not connect/disconnect external devices or install/remove internal cards during writing.
Troubleshooting Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: CD-DA, CD-Text, Photo CDTM (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2 Check the region code on the DVD. It must match that on the DVD Super Multi drive. Region codes are listed in the Optical media drives section in Chapter 2, The Grand Tour.
Troubleshooting SD card Refer also to Chapter 8, Optional Devices. Problem Procedure SD card error occurs Reseat the SD card to make sure it is firmly connected. Check the card’s documentation. You cannot write to an SD memory card Make sure the card is not write protected. You cannot read a file Make sure the target file is on the SD memory card inserted in the slot. If problems persist, contact your dealer. Memory Stick/Memory Stick Pro Refer also to Chapter 8, Optional Devices.
Troubleshooting Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. Touch Pad User’s Manual Problem Procedure On-screen pointer does not respond to Pad operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to return to its normal shape and try again to move it. Double-tapping does not work Try changing the double-click speed setting in the mouse control utility. 1.
Troubleshooting USB mouse Problem Procedure On-screen pointer does not respond to mouse operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it. Make sure the mouse is properly connected to the USB port. Double-clicking does not work Try changing the double-click speed setting in the mouse control utility. 1. To access this utility, click Start -> Control Panel -> Hardware and Sound -> Mouse icon. 2.
Troubleshooting Problem Procedure The fingerprint cannot be read due to injuries to the finger. Try the recognition process again using another enrolled finger. If fingerprints from all the enrolled fingers cannot be read, please logon by using the keyboard to input the password for the time being. If problems persist, contact your dealer. USB device Refer also to your USB device’s documentation.
Troubleshooting Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Check Windows Device Manager.
Troubleshooting i.LINK (IEEE1394) device Problem Procedure i.LINK device does not function Make sure the cable is securely connected to the computer and to the device. Make sure the device’s power is turned on. Reinstall the drivers. Open the Windows Control Panel and double-click the Add Hardware icon. Follow the on-screen directions. Restart Windows. If problems persist, contact your dealer. Modem Refer to Appendix C, AT Commands and Appendix D, S-registers.
Troubleshooting Problem Procedure Character display becomes garbled during a communication session In data transmission, make sure the parity bit and stop bit settings correspond with those of the remote computer. Check the flow control and communication protocol. You cannot receive an incoming call Check the rings before auto answer setting in your communications application. You can also use the ATS0 command. Refer to Appendix D, S-registers. If problems persist, contact your dealer.
Troubleshooting Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on. Make sure no optional Bluetooth PC card and Bluetooth Adapter are installed in the computer. The built-in Bluetooth function and an optional Bluetooth PC card cannot operate simultaneously. If problems persist, contact your dealer. Disposing of PC and PC batteries ■ Discard this PC in accordance with ordinances or rules of local regulations. For further information, contact your local government.
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first. Before contacting TOSHIBA, try the following: ■ Review troubleshooting sections in the documentation for software and peripheral devices.
Troubleshooting Outside of Europe In Europe Singapore TOSHIBA Singapore Pte. Ltd. 438B Alexandra Road #06-01 Alexandra Technopark Singapore 119968 Spain TOSHIBA Information Systems, ESPAÑA Parque Empresarial San Fernando Edificio Europa, la Planta, Escalera A 28830 Madrid United States of America TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 USA United Kingdom TOSHIBA Information Systems (U.K.) Ltd.
Troubleshooting 9-22 User’s Manual
PORTÉGÉ M400 Chapter 10 Legal Footnotes This chapter states the Legal Footnotes information applicable to TOSHIBA computers. In the text in this manual, *XX is used to show which Legal Footnotes description is related to TOSHIBA computers. Description(s) related to this computer are marked with a blue *XX in this manual. Clicking on *XX will display the related description. CPU*1 Central Processing Unit (“CPU”) Performance Legal Footnotes.
Legal Footnotes CPU performance may also vary from specifications due to design configuration. Under some conditions, your computer product may automatically shutdown. This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions. To avoid risk of lost data, always make back-up copies of data by periodically storing it on an external storage medium.
Legal Footnotes Battery Life*3 Battery life may vary considerably depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the design of individual components. Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
Legal Footnotes Wireless LAN*7 The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. [54Mbps is the theoretical maximum speed under the IEEE802.11 (a/b/g) standard.] The actual transmission speed will be lower than the theoretical maximum speed.
PORTÉGÉ M400 Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight (typical) 2.18 kilograms, configured with: 12.1”XGA, 512MB RAM, 40GB HDD, DVD-ROM&CD-R/RW drive, modem, LAN, Wireless LAN, 6cell battery pack, Tablet PC Pen. Weight will vary with other configurations. Above weights are measured at specific criteria. They are not guaranteed as the maximum weight of the actual product. Size 295 (w) × 249 (d) × 38.
Specifications Power Requirements AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 VDC 5.
Specifications User’s Manual Transmitting level -10 dBm Receiving level -10 to -40 dBm Input/output impedance 600 ohms ±30% Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.42bis Power supply +3.
Specifications A-4 User’s Manual
PORTÉGÉ M400 Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular parts on the screen on or off. The display controller supports VGA, SVGA and XGA modes on the internal LCD display panel. Two models are available: ■ 12.1" XGA, 1024 horizontal × 768 vertical pixels ■ 12.1" SXGA+, 1400 horizontal × 1050 vertical pixels Because of the LCD’s increased resolution, lines may appear broken in DOS mode.
Display Controller and Modes B-2 User’s Manual
PORTÉGÉ M400 Appendix C AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software. The format for entering AT commands is: ATXn where X is the AT command, and n is the specific value for that command. After you type in the command press Enter.
AT Commands Bn Communication standard setting This command determines the communication standard CCITT or Bell. B0 Selects CCITT V.22 mode when the modem is at 1200 bps. B1 Selects Bell 212A when the modem is at 1200 bps (default). B15 Selects V.21 when the modem is at 300 bps. B16 Selects Bell 103J when the modem is at 300 bps (default). Result Codes: OK n=0,1,15,16 ERROR Otherwise Dn Dial This command instructs the modem to dial a telephone number.
AT Commands Result Codes: OK n=0,1 ERROR Otherwise Hn Hook control This command instructs the modem to go on-hook to disconnect a call, or off-hook to make the phone line busy. H0 Modem goes on-hook (default). H1 Modem goes off-hook. Result Codes: OK n=0,1 ERROR Otherwise In Request ID information This command displays product information about the modem. I0 Returns modem identity string and driver version number. I3 Same as I0. I9 Returns region ID in English.
AT Commands Nn Modulation handshake This command controls whether or not the local modem performs a negotiated handshake at connection time with the remote modem when the communication speed of the two modems is different. N0 When originating or answering, this is for handshake only at the communication standard specified by S37 and the ATB command. N1 When originating or answering, begin the handshake at the communication standard specified by S37 and the ATB command (default).
AT Commands T Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. Vn DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents. V0 Displays result codes as digits. V1 Displays result codes as text (default).
AT Commands Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial tone. Enabled: The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds. Busy tone detect Disabled: The modem ignores any busy tones it receives. Enabled: The modem monitors for busy tones.
AT Commands &D2 If the DTR signal is not detected while in on-line data mode, the modem disconnects (default). &D3 Reset on the on-to-off DTR transition. Result Codes: OK n=0,1,2,3 ERROR Otherwise &F Load factory settings This command loads the configuration stored and programmed at the factory. This operation replaces all of the command options and the Sregister settings in the active configuration with factory values. &F Recall factory setting as active configuration. &Gn V.
AT Commands &Tn Self-test commands These tests can help to isolate problems if you experience periodic data loss or random errors. &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE. To work properly, the modem must be off-line.
AT Commands \N3 V.42, MNP, or buffered (default). The modem attempts to connect in V.42 error control mode. If this fails, it attempts to connect in MNP mode. If this fails, it connects in buffer mode and continues operation. This is also known as V.42/MNP auto reliable mode (same as &Q5). \N4 V.42 or disconnect. The modem attempts to connect in V.42 error control mode. If this fails, the modem disconnects. \N5 V.42. MNP or buffered (same as \N3). \N7 V.42. MNP or buffered (same as \N3).
AT Commands Result Codes: OK n=0,3 ERROR Otherwise C-10 User’s Manual
PORTÉGÉ M400 Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails. You can also customize certain AT commands such as the escape sequence and command line termination. The contents of the registers are changed automatically when you modify corresponding settings in your communication software.
S-registers S1 Ring counter This register is read only. The value of S1 is incremented with each ring. If no ring occurs over a six-second interval, this register is cleared. Range: 0-225 Default: 0 Units: rings S2 AT escape character (user defined) This register determines the ASCII values used for an escape sequence. The default is the + character. The escape sequence allows the modem to exit data mode and enter command mode when on-line. Values greater than 127 disable the escape sequence.
S-registers S5 Command line editing character (user defined) This register sets the character recognized as a backspace and pertains to asynchronous only. The modem will not recognize the backspace character if it is set to a value that is greater than 32 ASCII. This character can be used to edit a command line. When the echo command is enabled, the modem echoes back to the local DTE the backspace character, an ASCII space character, and a second backspace character.
S-registers S8 Comma pause time This register sets the time, in seconds, that the modem must pause when it encounters a comma (,) in the dial command string. In some countries/regions, S8 will set both wait before dialing and comma pause time. Range: 0-255 Default: 2 Units: seconds S11 DTMF dialing speed This register determines the dialing speed which is prefixed for each country/region. Range: 50-255 Default: 95 Units: .
S-registers S37 Dial line rate S37 = 0 (default) maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8 7200 bps S37 = 9 9600 bps S37 = 10 12000 bps S37 = 11 14400 bps S37 = 12 16800 bps S37 = 13 19200 bps S37 = 14 21600 bps S37 = 15 24000 bps S37 = 16 26400 bps S37 = 17 28800 bps S37 = 18 31200 bps S37 = 19 33600 bps User’s Manual D-5
S-registers AT command set result codes The following table shows the result codes.
S-registers CONNECT 33600 EC*1 60 Connection at 33600 bps DELAYED*2 88 Delay is in effect for the dialed number BLACKLISTED*2 89 Dialed number is blacklisted BLACKLIST FULL*2 90 Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression. V.42 - V.42 error control only.
S-registers D-8 User’s Manual
PORTÉGÉ M400 Appendix E V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably. Therefore, many users will experience throughput in the range of 28-50kbps under normal telephone line conditions. Upstream data flows at the V.
V.90 Table E-1 Result codes for a V.90 connection E-2 No.
V.90 * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V.42 error control and V.42bis data compression V42 V.42 error control only NoEC No error control protocol AT Command User’s Manual -V90=* V.90 Dial Line Rate -V90 sets the maximum V.90 downstream that the modem attempts to connect. -V90=0 V.90 disabled -V90=1 V.
V.
PORTÉGÉ M400 Appendix F Wireless LAN Card Specifications Form Factor PCI Express Mini Card Compatibility Network Operating System Media Access Protocol Data Rate ■ IEEE 802.11 Standard for Wireless LANS ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance. ■ Microsoft Windows® Networking ■ CSMA/CA (Collision Avoidance) with Acknowledgment (ACK) ■ Theoretical maximum speed: 54Mbps (IEEE802.11a/ IEEE802.
Wireless LAN R-F Frequency Modulation Technique ■ Band 5GHz (5150-5850 MHz) (Revision A) ■ Band 2.4GHz (2400-2483.5 MHz) (Revision B, G) ■ DSSS-CCK, DSSS-DQPSK, DSSS-DBPSK (Revision B) ■ OFDM-BPSK, OFDM-QPSK, OFDM-16QAM, OFDM-64QAM (Revision A, G) The range of the wireless signal is related to the transmit rate of the wireless communication. Communications at lower transmit range may travel larger distances.
Wireless LAN 10 2457*1 11 2462 12 2467*2 13 2472*2 *1 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/ regions that in which these channels can be used. When installing Wireless LAN cards, the channel configuration is managed as follows: ■ For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the Wireless LAN Access Point.
Wireless LAN F-4 108 5540 112 5560 116 5580 120 5600 124 5620 128 5640 132 5660 136 5680 140 5700 149 5745 153 5765 157 5785 161 5805 165 5825 User’s Manual
PORTÉGÉ M400 Appendix G TOSHIBA RAID TOSHIBA RAID provides the RAID function. 2 hard disk drives can be used to construct a RAID configuration (RAID-1: mirroring). When using RAID-1 (mirroring), the data is stored on 2 HDDs so that even if there are problems with one of the hard disk drive, the other hard disk drive can be used to recover the data. Please refer to the TOSHIBA RAID help for details. ■ By changing this setting you are reconfiguring your hard disk.
TOSHIBA RAID Windows Manual Setup Use the following procedures when manually setting up Windows. Before Setting Up Windows Before setting up Windows, create the TOSHIBA RAID Driver Disk and configure the BIOS setup program. Creating the TOSHIBA RAID Driver Disk 1. Connect the USB floppy disk drive and insert a floppy disk. 2. Copy all of the files located in C:\TOSAPINS\TOSHIBA RAID Driver to the floppy disk.
TOSHIBA RAID ■ Boot menu When 2 hard disk drives are connected, it is possible to select which hard disk drive to boot from in the boot menu. However, if a RAID configuration is used, the 2 hard disk drives are recognized as 1 drive and there is no change in the boot configuration no matter which hard disk drive is selected. ■ When using a RAID-1 (mirroring) configuration, the additional hard disk drive’s capacity must be equal to or more than the capacity of the existing hard disk drive.
TOSHIBA RAID Starting, Modifying and Ending the BIOS Setup Program Starting the BIOS Setup Program 1. Turn on your computer while pressing the Esc key. If Password = is displayed, enter the User Password and press the Enter key. Please refer to Chapter 6, the TOSHIBA Password Utility, for details about the User Password. The "Check system. Then press [F1] key." message is displayed. 2. Press the F1 key. The BIOS setup program will start up. Modifying the BIOS 1.
TOSHIBA RAID 3. The Execute Creation message is displayed once the configuration is modified. Move the cursor to the appropriate location and press the space bar to continue. Pressing the Home key will revert the modified Create State settings back to the Current State settings. 4. The following message will be displayed. Follow the instructions and press the keys in the order of 1, 2, 3, 4, [Enter]. S Warning: If you change the RAID array, you will need to install the OS again.
TOSHIBA RAID G-6 User’s Manual
PORTÉGÉ M400 Appendix H Bluetooth wireless technology Interoperability Bluetooth® Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ■ Bluetooth Specification Ver2.0+EDR, as defined and approved by The Bluetooth Special Interest Group. ■ Logo certification with Bluetooth wireless technology as defined by The Bluetooth Special interest Group.
Bluetooth wireless technology Interoperability ■ Bluetooth wireless technology is a new innovative technology, and TOSHIBA has not confirmed compatibility of its Bluetooth® products with all computers and/or equipment using Bluetooth wireless technology other than TOSHIBA portable computers. Always use Bluetooth® Cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards.
Bluetooth wireless technology Interoperability Bluetooth wireless technology and your Health The products with Bluetooth wireless technology, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by devices with Bluetooth wireless technology however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
Bluetooth wireless technology Interoperability L ‘ utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prét à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met.
Bluetooth wireless technology Interoperability Caution: Exposure to Radio Frequency Radiation The radiated output power of the Bluetooth® Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth® Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized.
Bluetooth wireless technology Interoperability 1. Sticker Please put the following sticker on computer incorporating this product. The frequency bandwidth of this equipment may operate within the same range as industrial devices, scientific devices, medical devices, microwave ovens, licensed radio stations and non-licensed specified low-power radio stations for mobile object identification systems (RFID) used in factory production lines (Other Radio Stations). 1.
Bluetooth wireless technology Interoperability Device Authorization This device obtains the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Telecommunications Business Law. The Name of the radio equipment: EYXF3CS JAPAN APPROVALS INSTITUTE FOR TELECOMMUNICATIONS EQUIPMENT Approval Number: D05-0074001 The following restrictions apply: Do not disassemble or modify the device.
Bluetooth wireless technology Interoperability H-8 User’s Manual
PORTÉGÉ M400 Appendix I AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 1.7 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
AC Power Cord and Connectors France: LCIE Switzerland: SEV Germany: VDE United Kingdom: BSI In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 215P (250V) or 1-15P (125V) and three pin plug configuration must be 615P (250V) or 5-15P (125V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II.
PORTÉGÉ M400 Appendix J TOSHIBA Anti-theft Protection Timer This feature allows you to set up a timer-activated BIOS password that will prevent unauthorised system access in the event of theft. When the time limit is exceeded, you are required to provide the Password or fingerprint authentication for the BIOS and Hard Disk Drive to gain access to the system. To set permissions and limits for the TOSHIBA Anti-theft Protection Timer please use the TOSHIBA Password Utility.
TOSHIBA Anti-theft Protection Timer J-2 User’s Manual
PORTÉGÉ M400 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Glossary IDE: integrated drive electronics I/O: input/output IrDA: Infrared Data Association IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte MS-DOS: Microsoft Disk Operating System OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock SCSI: small computer system interface SIO
Glossary analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements. antistatic: A material used to prevent the buildup of static electricity.
Glossary bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. C cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory.
Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component. components: Elements or parts (of a system) which make up the whole (system). computer program: A set of instructions written for a computer that enable it to achieve a desired result.
Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information. disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory.
Glossary E echo: To send back a reflection of the transmitted data to the sending device. You can display the information on the screen, or output it to the printer, or both. When a computer receives back data it transmitted to a CRT (or other peripheral device) and then retransmits the data to printer, the printer is said to echo the CRT. erase: See delete. escape: 1) A code (ASCII code 27), signaling the computer that what follows are commands; used with peripheral devices such as printers and modems.
Glossary graphics: Drawings, pictures, or other images, such as charts or graphs, to present information. H hard disk: A non-removable disk usually referred to as drive C. The factory installs this disk and only a trained engineer can remove it for servicing. Also called fixed disk. hard disk drive (HDD): An electromechanical device that reads and writes a hard disk. See also hard disk.
Glossary I/O: Input/output. Refers to acceptance and transfer of data to and from a computer. I/O devices: Equipment used to communicate with the computer and transfer data to and from it. IrDA 1.1: An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps. J jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit.
Glossary megahertz: A unit of wave frequency that equals 1 million cycles per second. See also hertz. menu: A software interface that displays a list of options on the screen. Also called a screen. microprocessor: A hardware component contained in a single integrated circuit that carries out instructions. Also called the central processing unit (CPU), one of the main parts of the computer. mode: A method of operation, for example, the boot mode, Sleep Mode or the Hibernation Mode.
Glossary output: The results of a computer operation. Output commonly indicates data. 1) printed on paper, 2) displayed at a terminal, 3) sent through the serial port of internal modem, or 4) stored on some magnetic media. P parallel interface: Refers to a type of information exchange that transmits information one byte (8 bits) at a time. See also serial interface. parity: 1) The symmetrical relationship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1.
Glossary R Radio frequency interference (RFI) shield: A metal shield enclosing the printed circuit boards of the printer or computer to prevent radio and TV interference. All computer equipment generates radio frequency signals. The FCC regulates the amount of signals a computing device can allow past its shielding. A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use.
Glossary subpixel: Three elements, one red, one green and blue (RGB), that make up a pixel on the color LCD. The computer sets subpixels independently, each may emit a different degree of brightness. See also pixel. synchronous: Having a constant time interval between successive bits, characters or events. system disk: A disk that has been formatted with an operating system. For MS-DOS the operating system is contained in two hidden files and the COMMAND.COM file.
Glossary Glossary-14 User’s Manual
PORTÉGÉ M400 Index A C AC adaptor 1-4 additional 1-18, 8-14 connecting 3-9 ASCII characters 5-8 Cache memory 1-3 Cleaning the computer 4-48 Cooling vents 2-3 B Battery charging 6-10 extending life 6-13 indicator 2-12, 6-4 location 2-7 monitoring capacity 6-11 real time clock 1-4, 6-6 safety precautions 6-7 save mode 1-12 types 6-5 Battery charger 1-18, 8-17 Battery pack 1-4, 2-8 additional 8-14 replacing 6-13 Bluetooth 1-8, 4-44 Bluetooth 2.
Index general conditions 3-2 placement 3-3 Ergonomics lighting 3-5 seating and posture 3-4 work habits 3-5 External monitor 1-7, 2-5, 8-21 problems 9-16 F Fingerprint Sensor location 2-9 problems 9-14 using 4-13 Floppy disk care 4-37 Fn + 1 (TOSHIBA Zooming Utility reduce) 5-5 Fn + 2 (TOSHIBA Zooming Utility enlarge) 5-5 Fn + Ctrl (enhanced keyboard simulation) 5-3 Fn + Enter 5-3 Fn + Esc (Mute) 5-3 Fn + F1 (Lock) 5-3 Fn + F10 (Arrow mode) 5-3 Fn + F11 (Numeric mode) 5-3 Fn + F12 (ScrLock) 5-3 Fn + F2 (P
Index K Keyboard 1-7, 5-1 emulating enhanced keyboard 5-2 Fn Sticky key 5-5 Function keys F1...
Index Sleep Mode 3-13 system auto off 6-20 turning off 3-12 turning on 3-11 Problems AC power 9-5 Analyzing symptoms 9-2 Battery 9-5 Bluetooth 9-18 DVD Super Multi drive 9-10 DVD-ROM&CD-R/RW drive 9-9 External monitor 9-16 Fingerprint sensor 9-14 Hard disk drive 9-8 Hardware and system checklist 9-3 i.
Index TOSHIBA Flash Cards 1-13 TOSHIBA HDD Protection 1-12 TOSHIBA Mic Effect 1-16 TOSHIBA Mobile Extension 115 TOSHIBA PC Diagnostic Tool 113 TOSHIBA Presentation button 1-11 TOSHIBA SD Memory Boot Utility 1-15 TOSHIBA SD Memory Card Format 1-15 TOSHIBA Zooming Utility 1-13 TV 8-22 X xD picture card 8-8 inserting 8-8 removing 8-8 U Ulead DVD MovieFactory for TOSHIBA 1-16 Ultra Slim Bay 2-5 changing modules 4-22 HDD adaptor (Black) 8-19 location of slot 2-4 options 1-20 USB 1-7 location 2-5 problems 9-1
Index Index-6 User’s Manual
