TOSHIBA STORAGE DEVICE DIVISION SR-C8002 CD-R/CD-RW DRIVE PRODUCT SPECIFICATION MAY 2001 REV. 1.
LIMITATION OF LIABILITY Those warranties in the express warranty separately agreed between TOSHIBA and your company are the only warranties given to the consumer and are in lieu of any other warranties, whether express or implied with regard to this component. TOSHIBA expressly and unequivocally disclaims the warranties of merchantability and fitness for a particular purpose.
DO NOT use this equipment in the system such as medical equipment which may cause personal injury or property damages resulting from malfunction of this equipment and unexpected data corruption or data error in reading operation. 4. Turn off the power for this equipment and wait more than one (1) minute before you eject the disc using the emergency eject mechanism when a disc cannot be ejected for some reasons in order to avoid the risk of damages to the disc. Notice 1.
Contents 1. Introduction ---------------------------------------------------------------------------------------------------------------------- 1 2. Features -------------------------------------------------------------------------------------------------------------------------- 1 3. Specifications ------------------------------------------------------------------------------------------------------------------ 2 3.1.
7.2. Current Drain -------------------------------------------------------------------------------------------------------18 7.2.1.Sleep ------------------------------------------------------------------------------------------------------------18 7.2.2. Standby ----------------------------------------------------------------------------------------------------------18 7.2.3. Continuous Read -------------------------------------------------------------------------------------------18 7.2.4.
1. Introduction This document describes TOSHIBA's SR-C8002 CD-R/RW Drive. 2. Features SR-C8002 reads digital data stored on CD-ROM media and CD-Audio discs. The CD-ROM media has a 12 cm or 8 cm diameter. It typically contains approximately 600 MBytes or 200 MBytes of information respectively. (1 MByte=220 Bytes) This drive reads CD-ROM media at maximum 24 times faster rotational speed. This drive is a new generation drive with highest performance such as 120 ms access Time.
3. Specifications 3.1.
(6) Transfer Rate Sustained Block Transfer Rate 776-1,800 Block/s (10.3-24X CAV) 300-450 Block/s (4-6X PCAV) Sustained Data Transfer Rate Mode-1: Mode-2: 10.3X-24X CAV 1,552-3,600 KByte/s 4X-6X PCAV 600-900 KByte/s 10.3X-24X CAV 1,769-4,104 KByte/s 4X-6X PACV 684.4-1,026.6 KByte/s Burst Data transfer Rate 16.7 MByte/s (PIO Mode 4 ) 16.
(10) Drawer Load/Release Load: Release: Manual (a) Electrical Release (Release Button) (11) Air Flow (b) Release by ATAPI command (c) Emergency Release Not Required (12) Acoustic Noise 40 dB (IEC 179 A weighted at 1 m) (13) Power Supply +5 V (details in Section 7) 3.2. Environmental Conditions This drive should be used under the conditions listed below. 3.2.1.
3.2.3.Vibration (1) Operating (CD 10.3-24X Read) (1 Oct/min) ---------------- no hard error ----5 to 500 Hz 2.45 m/s2 [0.25 G] (0-p) (excluding resonance point) (2) Operating (Write) (1 Oct/min) ---------------- no hard error ----5 to 500 Hz 2.45 m/s2 [0.25 G] (0-p) (excluding resonance point) (3) Non-operating (1 Oct/min) --------- no damage ----5 to 10 Hz 5 mm (p-p) 10 to 500 Hz 9.8 m/s2 [1 G] (0-p) (4) Shipping (Packaged) (1 Oct/min) ----- 3.2.4.
3.3. Installation Conditions 30 ° 15 ° 15 ° 15 ° 15 ° 15 ° 15 ° 15 ° 15 ° 15 ° Figure 1 Mounting angle 3.3.1. Equipment (1) When mounting the equipment, use four M2-P0.4 tapping holes located on the left and right sides of the equipment. (2) The opposite surface of the bearing surface (fitting surface when mounting) of the tapping holes must be kept flat so that the bearing surface can be fit evenly. (3) Use the mounting screws which do not enter deeply inside the equipment more than specified value.
(4) Do not add the force beyond the indicated force on the top and bottom cover of the equipment. (The restricted force range for the top cover is shown in the Figure 2.) (For the bottom cover, the applied force should be less than 2N on whole area.) 2N 129 1N R63 0.5 N R59 37 R46 24 Do not add the force 5.
( Unit: mm ) Figure 3 External Dimensions 8/24 SR-C8002 Rev.1.
3.5. Reliabilites 3.5.1. Error Rate (1) Hard Read Error Rate (Byte Error Rate) ----- Allowing 5 Retries(default) ----Mode 1:10-15 Max Mode 2:10-12 Max (2) Seek Error Rate --- Allowing 10 Retries (default) 10 -6 Max 3.5.2. MTBF Assumptions: Power On Hours On/Off Cycles Number of Access Operating Duty Cycle (Read) Operating Duty Cycle (Write) 60,000 h 5,436 h/year 313 cycles/year 600,000 accesses/year 20 % of Power On Time (Reading/Seeking) 2 % of Power On Time (Writing/Seeking) 3.5.3. MTTR 0.5 h 3.5.4.
10/24 LED Drawer Release Detector Release Switch Release Solenoid Position Detector PUH GPIO 63F49 TPIC1318 Power Driver Power Driver Power Driver Power Driver BH6526FV Focus Amp Command Dec. RAM Int. Control Timer FLASH ROM Micro Processor CD-BUS Interface FV Converter 33.86 MHz Comparator Feed Motor Disc Motor RF Amp EQL Tracking Amp TA1323F Commad DCC Converter Disc EQL D/A Digital Audio Decoder Audio D/A D-RAM Interface DRAM (16M) 22.
5.Functions 5.1. Disc Data Configurations 5.1.1. CD-ROM Data Configurations Figure 5 shows how the data is structured in program units 1 block=1/75 s TNO Time 0 TOC 1-Disc SYNC 12 bytes Lead-in Min Sec Block 2 approx. ~ AA ~ 300 k-Blocks ~ ~ Mode ~ Block 2 Blocks(0~74) User Data 2048 bytes in Mode-1 2336 bytes in Mode-2 Min Sec 4 bytes Header Block 1 Block 1 Minutes Second(0~59) ~ ECC (Mode-1) 288 bytes ~ ~ Lead out Figure 5 CD-ROM Disc Data Configuration 5.1.2.
5.2. Power ON/OFF Timing Figure 7 shows the initialization sequence Power ON or ATAPI-RST Max. 550 ms "Command" Receivable System Initialization Max 2 s Focus Search Max 3.5 s Spindle ON Learning Max 30s, Typ 12 s (Single Session Disc) "Read-Command" Stand-by Acceptable "TEST UNIT READY" Command "Check Condition" Status "Good" Status Figure 7 Initialization Sequence 6. Interface (1) The interface is based on T13/1321D (AT Attachment with Packet Interface-5, ATA/ATAPI-5) Revsion 3 (Feb.
6.2.Signal summary The physical interface consists of single ended TTL compatible receivers and drivers communicating through a 50P-connector as shown in Figure 11 and Figure 12 "Interface connector". 6.2.1. Signal Specification Figure 8 shows the Signal Specifications Receivers/Drivers Caracteristics withoutExternal pullup Resistor Type Sig.
6.2.2.Timing of Host Interface (PIO) Figure 9 shows the Host Interface Timings t0 Address valid*1 t2 t1 t9 DIOR-/DIOW-*1 t2i Write data valid*1 t3 Read data valid*1 t4 t5 t6Z t7 t6 IOCS16-*1 tA IORDY tB t8 tRD *1: In all timing diagrams, the low line indicator negated, and the upper line indicators asserted.
6.2.3.Timing of Host Interface (DMA Multi) Figure 10 shows the Host Interface DMA multi word Timings t0 DMARQ tL DMACK-*1 tK tD tI tJ DIOR-/DIOW-*1 tZ tE Read DD0-15 tF Write DD0-15 tG tH *1: In all timing diagrams, the low line indicator negated, and the upper line indicators asserted.
6.3. Connector Figure 11 shows the connector and Figure 12 shows the interface pin assignments Use Japan Aviation Electronics Industry Limited KX15-50KLD L or equivalent. Conformable connector is Japan Aviation Electronics Industry Limited KX14-50 series.
6.4.
ATA Command for ATAPI No. OP Code Command Description - 00h Nop 1 2 08h ATAPI Soft Reset 20/21h Read Sector (s) 3 4 5 6 7 8 9 10 11 12 13 14 90h Execute Drive Diagnostics A0h ATAPI Packet Command A1h ATAPI Identify Device E0h Standby Immediate E1h Idle Immediate E2h Standby E3h Idle E5h Check Power Mode E6h Sleep E7h Flush Cache ECh ATA Identify Device EFh Set Feature 7. Power Requirements 7.1. Source Voltage +5 V +/-5 % (Operating) +5 V +/-8 % (Start up) 7.1.1.
8.CD Audio (Test condition: Ordinary temperature) 8.1. Analog Out --- in case of the attenuator is set at 0 dB by the command --(1) Output Level 0.8 V (rms)+/-1 dB (2) Type Unbalanced (3) Load Impedance 47 kOHM min (4) Frequency Response 20 Hz to 20 kHz+/-3.0 dB. (at 47 kOHM Load) (5) Distortion 0.04 % Max. (at 1 kHz w/20 kHz LPF) (6) Signal to Noise Ratio 80dB Typ (IEC179 A-Weighted) 8.2. Audio Modes (1) 16 Modes including 'Stereo', 'Lch Mono', 'Rch Mono' and 'Mute' are selectable by command.
10. Busy Indicator The LED at Front Bezel (Busy Indicator) indicates the drive status. Color: AMBER (1) After Drawer is closed, Busy Indicator start blinking at 0.8 s intervals, and then ----(1-1) Turns off when the drive in the 'Idle' status. 0.8 s Light Off Figure 13 Idle (1-2) Continuously off when no disc is mounted. 0.8 s Light Off Figure 14 No disc (1-4) Continuously on when media has problem 0.
11.Emergency Release Execute following procedure only in the case of emergency (Drawer will not release and disc can not be removed although pressing Release Button). (1) Turn the drive supplying power off. (2) Insert solid bar (like paper clip) into Emergency Release hole and push as shown in Fig.19. Then Drawer will be released. (3) After removed the disc, gently push Drawer to close. 15 mm diameter 1.0 mm Figurer 19 Emergency Release 12.
13. Electrostatic Discharge Standard IEC61000-4-2 (1) Operating 8 kV or less (2) Damage including 15 kV or more 14. Accessories None 15. Packaging (1) 50 units in a bulk package 24 bulk packs on one pallet. * All transportation is allowed with pallet. (Transportation with bulk package is not allowed.) (2) 20 units in a bulk package 24 bulk packs on one pallet. (Transportation with bulk package is allowed.) (3) 1 unit in a bulk package (Transporttation with bulk package is allowed.) 16.
TOSHIBA TOSHIBA EUROPE GMBH EU-Declaration of Conformity Product: CD-R/RW Drive Manufacturer(s): Toshiba Corporation 1-1, Shibaura 1-chome, Minato-ku, Tokyo 105-8001 Japan See page 2 for other locations Model: SR-C8002 Options: None Toshiba declares that the above mentioned product(s) with or without the listed options comply to the EU-Directives and standards as listed on page 2.
24/24 SR-C8002 Rev.1.0 SR-C8002 CD-R/RW Drive Address X Related EU-Directive 89/336/EEC Radio disturbance characteristics-IT equipment Class B (including domestic environment) Information Technology equipment-Immunity characteristices Limits and methods of masurement CD: 4 kV, ID: 4 kV, AD: 8 kV 3 V/m, 80-1000 MHz, 1 kHz 80 % AM AC-line: 1 kV, I/F 0.5 kV f: 5 kHz, Polarity: +/AC-line: 2 kV/1 kV, Polarity: +/3 V, 0.15-80 MHz, 80 % AM 1 A/m, 50 Hz >95 % 0.
Deviation List Page Item 1 2. Features 2 3 Rev # 0.5 This drive is a new generation..... .....such as 95 ms access Time. Rev # 1.0 This drive is a new generation..... .....such as 120 ms access Time. CD-RW Approx. 5,100 rpm (10.3-24X CLV) Approx. 1,200-2,000 rpm (4-5.7X PCAV) TBD (Target Max 10X PCAV) Hight Speed CD-RW ----- Approx. 5,100 rpm (10.3-24X CAV) Approx. 1,290-2,000 rpm (4-6X PCAV) Approx. 1,290-2,000 rpm (4-6X PCAV) Approx. 2,570-4,000 rpm (8-12X PCAV) 3.1.
Page 12 Item Figure 7 Focus Search Spindle ON Stand-by 6. Interface Rev # 0.5 TBD TBD TBD (1) The interface is based on X3T13/D96153 Revsion 18..... (1) The interface is based on T13/1321D (AT Attachment with Packet Interface-5, (2) 64 17 18 6.4. Support Command List ATAPI Packet Command 7.2. Current Drain 7.2.1.Sleep 7.2.2.Standby 7.2.3. Continuous Read 7.2.4.Idle 7.2.5. Average 7.2.6. Maximum 7.2.7. Peak in executing Access 7.2.8. Write 22 16. CE Declaration of conformity Rev # 1.
