TOSHIBA Satellite U400/U400D Satellite Pro U400/U400D PORTÉGÉ M800/M800D Portable Personal Computer User's Manual
Copyright © 2008 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein. TOSHIBA Satellite U400/U400D, Satellite Pro U400/U400D, PORTÉGÉ M800/M800D Series Portable Personal Computer User's Manual First edition June 2008 Ownership and copyright of music, video, computer programs, databases, etc.
Trademarks Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. DirectX, AcriveDesktop, DirectShow, and Windows Media are registered trademarks of Microsoft Corporation. Intel, Intel Core, Celeron, Centrino and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.
When Using Your Computer Do not operate your portable computer for an extended period of time with the base resting directly on your body. With extended operation, heat can potentially build up in the base. Allowing sustained contact with the skin could cause discomfort or, eventually, a burn. ■ Do not attempt to service the computer yourself. Always follow installation instructions closely.
FCC information FCC notice “Declaration of Conformity Information” This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
BSMI notice (Taiwan only) EU Declaration of Conformity TOSHIBA declares that this product conforms to the following Standards: Supplementary “The product complies with the requirements of Information: the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC and/or the R&TTE Directive 1999/5/EC.” This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany.
Modem warning notice Conformity Statement The equipment has been approved to [Council Decision 98/482/EC - "TBR 21"] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Japan regulations Region selection If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection. Redial Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer.
Telephone company procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations, or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice in writing to allow you to make any changes necessary to maintain uninterrupted service.
Instructions for IC CS-03 certified equipment 1. The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia. The use of other country/region setting while the modem is attached to the Australian PSTN would result in you modem being operated in a non-compliant manner.
Notes for use of this device in New Zealand ■ The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers. Failure to operate should not be reported as a fault to Telecom.
■ When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: ■ a person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been successfully switched through the network. ■ caller identification information (which occurs between the first and second ring cadences) is not destroyed. ■ The preferred method of dialling is to use DTMF tones (ATDT...
The charge for a Telepermit assessment is $337.50. An additional charge of $337.50 is payable where an assessment is based on reports against non-Telecom New Zealand Specifications. $112.50 is charged for each variation when submitted at the same time as the original. An invoice for $NZ1237.50 will be sent under separate cover. Following information is only for EU-member states: The symbol indicates that this product may not be treated as household waste.
Visit http://www.energystar.gov or http://www.energystar.gov/power management for more information regarding the ENERGY STAR Program. Optical disc drive safety instructions Be sure to check the international precautions at the end of this section. Panasonic DVD Super Multi UJ-862E/UJ-862A ■ The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference.
Hitach-LG Data Storage DVD Super Multi GSA-U20N/GSA-U20F ■ The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
International Precautions CAUTION: This appliance contains a laser system and is classified as a "CLASS 1 LASER PRODUCT." To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest "AUTHORIZED service station." To prevent direct exposure to the laser beam, do not try to open the enclosure.
OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Important Notice Copyrighted works including, but not limited to music, video, computer program, databases are protected by copyright laws. Unless specifically permitted under applicable copyright laws, you cannot copy, modify, assign, transmit or otherwise dispose of any copyrighted work with the consent of the owner of the copyright. Please take notice that unauthorized copying, modification, assignment, transmission and disposition may be subject to claims for damages and penalties.
xx User’s Manual
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Heat injury ■ Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time, for example if you rest the computer on your lap or if you keep your hands on the palm rest, your skin might suffer a low-heat injury.
Table of Contents Preface Manual contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxix Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxx Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxx Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxx Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Writable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9 CDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10 DVDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10 DVD Super Multi drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10 AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the TOSHIBA Face Recognition . . . . . . . . . . . . . . . . . . . . . . . Note on Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How to register the Face Recognition Data . . . . . . . . . . . . . . . . . . How to Delete the Face Recognition Data . . . . . . . . . . . . . . . . . . . How to launch the help file . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting LAN cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-36 Disconnecting LAN cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-37 Cleaning the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-37 Moving the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-38 Using the Hard Disk Drive (HDD) Protection . . . . . . . . . . . . . . . . . . .4-38 TOSHIBA HDD Protection Properties. . . .
Chapter 7 HW Setup Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 HW Setup Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Chapter 8 Optional Devices ExpressCard Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Inserting an ExpressCard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Removing an ExpressCard . . . . . . . . . . . . . . . . . . . . .
Recovery Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-9 DVD Super Multi drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-9 Pointing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-13 Memory expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preface Congratulations on your purchase of the TOSHIBA Satellite U400/U400D, Satellite Pro U400/U400D, PORTÉGÉ M800/M800D Series computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells you how to set up and begin using your TOSHIBA Satellite U400/U400D, Satellite Pro U400/U400D, PORTÉGÉ M800/ M800D Series computer.
Preface Chapter 4, Operating Basics, includes instructions on using the following devices: TouchPad, Sound System, optical media drives, modem, wireless communication and LAN. It also provides tips on care of the computer, and CD/DVDs. Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hot keys. Chapter 6, Power and Power-Up Modes, gives details on the computer's power resources and battery save modes.
Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
Preface xxxii User’s Manual
Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer's features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Introduction Software Microsoft® Windows Vista™ The following software is preinstalled: ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Microsoft® Windows Vista™ Microsoft Internet Explorer TOSHIBA Value Added Package TOSHIBA Hardware Setup TOSHIBA Supervisor Password TOSHIBA Assist TOSHIBA ConfigFree TOSHIBA DVD PLAYER TOSHIBA FingerPrint Utility (FingerPrint support model only) TOSHIBA SD Memory Utilites TOSHIBA Disc Creator TOSHIBA Face Recognition TOSHIBA Acoustic Silencer ■ Ulead DVD MovieFactory® for TOSHIBA ■ Presto! B
Introduction Features Please visit your region’s web site for the configuration details of the model that you have purchased. Processor Built-in Depend on the model you purchased. Please visit your region’s website for the configuration details of the model that you have purchased. Chipset Mobile Intel® PM45/GM45 Express Chipset or AMD M780G/M780V Chipset Memory Slots PC2-5300 or PC2-6400 512 MB, 1024 MB or 2048 MB memory modules can be installed in the two memory slots.
Introduction Power Battery Pack Your computer is powered by a rechargeable lithium-ion battery pack. RTC Battery The internal RTC battery backs up the Real Time Clock and calendar. AC Adaptor The universal AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord. Because it is universal, it can receive a range of AC voltage from 100 to 240 volts; however, the output current varies among different models.
Introduction DVD Super Multi drive Some models are equipped with a full-size DVD Super Multi drive module that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROM's at maximum 8 speed and CD-ROM's at maximum 24 speed. It writes CD-R's at up to 24 speed, CD-RW's at up to 16 speed, DVD-R's at maximum 8 speed, DVD-RW's at maximum 6 speed.
Introduction Built-In 13.3" WXGA 16 M colors, with the following resolution: 1280 horizontal × 800 vertical pixels. Graphics Controller Graphics controller maximizes display performance. Refer to Display Controller and Modes section in Appendix B, Display Controller and Modes for more information. Keyboard Built-In TOSHIBA Vista keyboard, 85 keys or 86 keys, compatible with IBM enhanced keyboard, embedded numeric overlay, dedicated cursor control, and keys.
Introduction Slots ExpressCard Slot The ExpressCard slot that can accommodate two standard module formats; an ExpressCard/34 module and an ExpressCard/54 module. An ExpressCard module is a small add-in card technology based on the PCI Express and Universal Serial Bus (USB) interfaces. Multiple Digital Media Card Slot Supports SD/SDHC memory card, MMC, MEMORY STICK, MEMORY STICK PRO and xD Picture card Multimedia Web Camera Record/Send still or video images with this integrated webcam.
Introduction Wireless LAN The Wireless LAN feature is not available on all models. Where present, it supports the A,B,G and draft N standards but it is compatible with other LAN systems based on Direct Sequence Spread Spectrum / Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard. ■ Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36, 24, 18, 12, 9 and 6 Mbit/s. (IEEE 802.
Introduction Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Hot Keys Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program. Keypad Overlay A ten-key pad is integrated into the keyboard. Refer to the Keypad overlay section in Chapter 5, The Keyboard, for instructions on using the keypad overlay.
Introduction Low Battery Automatic Hibernation *1 When battery power is exhausted to the point that computer operation cannot be continued, the system automatically enters Hibernation Mode and shuts down. This can be specified in the Power Options.
Introduction TOSHIBA Power Saver TOSHIBA Power Saver provides you with the features of more various power supply managements. TOSHIBA Zooming Utility This utility allows you to enlarge or reduce the icon size on the Windows Desktop, or the zoom factor associated with specific supported applications. TOSHIBA PC Diagnostic Tool The TOSHIBA PC Diagnostic Tool will display basic system configuration information and allow the functionality of some of the computer's builtin hardware devices to be tested.
Introduction TOSHIBA Assist TOSHIBA Assist is a graphical user interface that provides easy access to help and services. HW Setup This program lets you customize your hardware settings according to the way you work with your computer and the peripherals you use. To start the utility, double click the TOSHIBA Assist on your desktop, select OPTIMIZE tab, and click TOSHIBA Hardware Settings.
Introduction FingerPrint utility This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. (depending on the model purchased.) By enrolling the ID and password to the fingerprint authentication device, it is no longer necessary to input the password from the keyboard. Just by swiping the finger against the fingerprint sensor, the following functions will be enabled: ■ Log-on to Windows and access a security enabled homepage through IE (Internet Explorer).
Introduction TOSHIBA ConfigFree ConfigFree is a suite of utilities to allow easy control of communication devices and network connections. ConfigFree also allows you to find communication problems and create profiles for easy switching between location and communication networks. To run ConfigFree, click , select All Programs, TOSHIBA, Networking and then click ConfigFree.
Introduction Options You can add a number of options to make your computer even more powerful and convenient to use. Refer to Chapter 8 Optional Devices, for details. The following options are available: Memory expansion Two memory modules can be installed in this computer. Use only PC2-5300 or PC2-6400* compatible DDRII memory modules. See your TOSHIBA dealer for details. * The availability of DDRII depends on the model you purchased.
Introduction 1-16 User’s Manual
Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed The following figure shows the computer's front with its display panel in the closed position.
The Grand Tour 2-2 Volume Dial Use this dial to adjust the volume of the stereo speakers or headphones. Infrared Receiver Window An infrared receiver window is provided with some models. This is a sensor window that receives signals from the remote control which is provided with your computer. Wireless Activity LED Indicates whether the wireless LAN or Bluetooth is active or not.
The Grand Tour Left side The following figure shows the computer's left side. HDMI External Monitor Port Cooling Vents eSATA/USB combo port USB Port i.LINK Microphone (IEEE1394a) Port Jack The left side of the computer ExpressCard Slot Headphone (S/P DIF) Jack External Monitor Port This 15-pin port lets you connect an external video display. Cooling Vents Cooling vents help prevent the CPU from overheating.
The Grand Tour eSATA/ Universal Serial Bus (USB 2.0) ports Universal Serial Bus ports which comply to the USB 2.0 standard, are provided. The ports with the icon ( ) have USB Sleep and Charge function. eSATA/USB combo port eSATA/USB combo port supports the USB 2.0 and the eSATA function. Microphone Jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input. Headphone (S/P DIF) Jack This jack outputs analog audio signals.
The Grand Tour FM LAN Jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-TX). Refer to Chapter 4, Operating Basics, for details. Modem Jack The modem jack allows you to use a modular cable to connect the modem directly to a telephone line. (Depends on the model you purchased.) ■ In case of a lightning storm, unplug the modem cable from the telephone jack.
The Grand Tour Underside The following figure shows the underside of the computer. Make sure the display is closed before turning over your computer. Battery Pack Battery Release Latch Battery Pack Lock Hard Disk Cover Cooling Vents Memory Module and Wireless LAN Cover The underside of the computer 2-6 Memory Module and Wireless LAN Cover This cover protects two memory module sockets -one or two modules are pre-installed. Refer to the Memory expansion section in Chapter 8, Optional Devices.
The Grand Tour Front with the display open This section shows the front of the computer with the display open. Refer to the appropriate illustration for details. To open the display, lift the front of the display. Position the display at a comfortable viewing angle.
The Grand Tour 2-8 Built-in microphone The microphone is used with the Web Camera to talk to other Web Camera users and to record messages on windows media. Power Button Turns the computer on and off and puts it into Hibernation mode and wakes it up from Sleep mode. Mute Button Press this button to Mute volume. (Provided with some models) CD/ DVD Button Pressing this button will launch an application program that allows for playing of CDs or DVDs.
The Grand Tour Fingerprint Sensor Just by swiping the finger against the fingerprint sensor, the following functions will be enabled: Log-on to Windows and access a securityenabled homepage through IE (Internet Explorer) Files and folders can be encrypted/decrypted and third party access to them prevented. Disable the password-protected screensavcr when returning from power-saving (Sleep) mode. System boot authentication and Single Touch Boot feature.
The Grand Tour CDs ■ CD-R discs can be written only once. The recorded data cannot be erased or changed. ■ CD-RW discs can be recorded more than once. Use either 1, 2, or 4 multi speed CD-RW discs or high-speed 4- to 10-speed discs. The write speed of the ultra-speed CD-RW discs (Ultra-speed is available on the DVD-ROM & CD-R/RW drive only) is a maximum of 24-speed. DVDs ■ DVD-R, DVD+R, DVD-R DL and DVD+R DL discs can be written only once. The recorded data cannot be erased or changed.
The Grand Tour AC adaptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any country/region. To recharge the battery, simply connect the AC adaptor to a power source and the computer. Refer to Chapter 6, Power and Power-Up Modes, for details.
The Grand Tour Remote controller A remote controller, which is provided with some models, enables you to perform some functions of your computer from a distant location. You can use your remote controller with Media Center to play CDs, DVDs and videos, to view pictures. The remote controller helps you to control the playback of a movie through Media Center. Using the remote controller, you can: ■ Navigate and control all Media Center windows. ■ Control the video.
The Grand Tour User’s Manual Power Starts or terminate the operating system. This button functions like the power button of your computer. By default, the Sleep mode is equivalent to the power off state of your computer. To change the setting, click Start Æ Control panel ÆSystem and Maintenance Æ Power Options ÆChoose what the Power button does. The following four options are available: Do nothing, Sleep, Hibernate and Shut down. Volume + Increases the volume while viewing DVDs or replaying CDs.
The Grand Tour Fast forward Moves the media (video, DVD, music, and so on) forwards. Replay Moves media backward (seven seconds for videos, one music track or one DVD chapter at a time). Stop Stops the media currently playing. Skip Moves media forward (30 seconds for videos, one music track or one DVD chapter). Using the remote controller Some computers include a remote control unit, which allows you to control some of your computer’s functions from a distant location.
The Grand Tour 30 Degrees 15 Degrees (Vertically) 30 Degrees Infrared Receiver Window 5M Remote Controller Operational range of the remote controller Even if within the effective scope as described above, the remote controller may malfunction or not work correctly in the following cases. ■ When an obstacle stands between the infrared receiver window of your computer and the remote controller. ■ When direct sunlight or strong fluorescent light strikes the infrared receiver window.
The Grand Tour Installing/Removing batteries Be sure to install the provided CR2016 type batteries before using the remote controller. The procedures for installing and removing the batteries vary depending on the type of the remote controller. Check the type and then install or remove the batteries as instructed. Store the battery for the remote controller beyond the reach of children. If a child swallows a battery, this might result in choking. If it happens, contact a doctor immediately.
The Grand Tour Installing the batteries 1. Open the battery cover on the back side of the remote controller. Battery Cover Opening the battery cover 2. Be sure to place the batteries with correct polarities. Press the battery down to the stopper then push it forward to fit into the battery case. Stopper Battery Inserting the batteries 3. Close the battery cover. Close the cover securely until it clicks.
The Grand Tour Slim size remote controller 1. Open the battery cover on the back side of the remote controller. 2. Hold down the stopper and slide the battery out of battery case. Stopper Battery Removing the batteries 3. Insert the battery in place. Be sure to place the batteries with correct polarities. Press the battery down to the stopper then push it forward to fit into the battery case. 4. Close the battery cover. Close the cover securely until it clicks.
Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: Be sure also to read the Instruction Manual for Safety and Comfort. This guide, which is included with the computer, explains product liability.
Getting Started Installing the battery pack To install a battery, follow the steps below. ■ The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Do not touch the latch while holding the computer. Or you may get injured by the dropped battery by unintentional release of the latch.
Getting Started Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.
Getting Started 2. Connect the AC adaptor's DC output plug to the DC IN 19V jack on the back of the computer. Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Lift the panel up and adjust it to the best viewing angle for you. Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer.
Getting Started Turning on the power This section describes how to turn on the power. After you turn on the power for the first time, do not turn it off until you have set up the operating system. Refer to the section Windows Vista setup. Press and hold the computer's power button for two or three seconds. Turning on the power Windows Vista setup When you first turn on the power, the computer's initial screen is the Microsoft® Windows Vista™ Startup Screen Logo. Follow the on-screen directions.
Getting Started Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Sleep Mode. Shut Down mode (Boot mode) When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system’s main screen. 1. If you have entered data, save it to the hard disk. 2. Make sure all disk (disc) activity has stopped, then remove the CD/ DVDs. Make sure the Disk LED and ODD indicators are off.
Getting Started ■ Before entering Sleep Mode, be sure to save your data. ■ Do not install or remove a memory module while the computer is in Sleep Mode. The computer or the module could be damaged. ■ Do not remove the battery pack while the computer is in Sleep Mode (unless the computer is connected to an AC power source). Data in memory will be lost.
Getting Started Sleep Mode limitations Sleep Mode will not function under the following conditions: ■ Power is turned back on immediately after shutting down. ■ Memory circuits are exposed to static electricity or electrical noise. Hibernation Mode The hibernation feature saves the contents of memory to the hard disk when the computer is turned off. The next time the computer is turned on, the previous state is restored. The hibernation feature does not save the status of peripheral devices.
Getting Started Automatic Hibernation Mode The computer will enter Hibernation mode automatically when you press the power button or close the Display Screen. First, however, make the appropriate settings according to the steps below. 1. Open the Control Panel. 2. Open System and Maintenance and open Power Options. 3. Select the Choose what the power button does. 4. Enable the desired Hibernation settings for When I press the power button and When I close the lid. 5. Click the Save changes button.
Getting Started System Recovery Options About 1.5GB hidden partition is allocated on the hard drive for the System Recovery Options. The System Recovery Options feature will be unusable if this partition is deleted. System Recovery Options The System Recovery Options feature is installed on the hard disk when shipped from the factory. The System Recovery Options menu includes some tools to repair startup problems, run diagnostics or restore the system.
Getting Started 3. Turn on your computer to open Windows Vista. 4. Insert the (first) blank media into the tray of the Optical Drive. 5. Double Click the Recovery Disc Creator icon on the Windows Vista desktop, or select the application from Start menu. 6. After TOSHIBA Recovery Disc Creator starts, select the type of media and the title you wish to copy to the media then click the Create button.
Getting Started Restoring the preinstalled software from Recovery Media If the preinstalled files are damaged, use the Recovery Media you created, or HDD recovery to restore them. To restore the operating system and all preinstalled software, follow the steps below. When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost. 1. Load the Recovery Media in the optional optical media drive and turn off the computer's power. 2.
Chapter 4 Operating Basics This chapter gives information on basic operations including using the TouchPad, optical media drives, sound system, modem, the wireless LAN and LAN. It also provides tips on caring for your computer. Using the TouchPad To use the TouchPad, simply touch and move your finger tip across it in the direction you want the on-screen pointer to go.
Operating Basics Do not press on the TouchPad too hard or press a sharp object such as a ball point pen against the TouchPad. The TouchPad could be damaged. For some functions, you can tap the TouchPad instead of pressing a control button. Click: Tap the TouchPad once Double-click: Tap the TouchPad twice Drag and drop: 1. Hold down the left control button and move the cursor to drag the item you want to move. 2. Lift your finger to drop the item where you want it.
Operating Basics How to swipe the finger Using the following steps when swiping fingers for fingerprint registration or authentication will help to minimize authentication failures: 1. Align the first joint of the finger to the center of the sensor. Lightly touch the sensor and swipe finger levelly towards you. 2. While lightly touching the sensor, swipe the finger towards you until the sensor surface becomes visible. 3. Ensure the center of the fingerprint is on the sensor when swiping the finger.
Operating Basics Points to note about the fingerprint sensor Failure to follow these guidelines might result in (1) damage to the sensor or cause sensor failure, (2) finger recognition problems, or lower finger recognition success rate. ■ Do not scratch or poke the sensor with your nails or any hard or sharp objects. ■ Do not press the sensor strongly. ■ Do not touch the sensor with a wet finger or any wet objects. Keep sensor surface dry and free of water vapor.
Operating Basics ■ The fingerprint for each finger is different and unique. Please ensure that only the registered or enrolled fingerprint or fingerprints are used for identification. ■ Check sliding position and speed. ■ Fingerprint data is enrolled up to 30~34. ■ Fingerprint data is stored into the nonvolatile memory in the fingerprint sensor. Deleting the fingerprint data with Delete menu on Fingerprint Software Management before you dispose the computer is recommended.
Operating Basics Points to note about the fingerprint utility ■ If Windows Vista™’s file encryption function EFS (Encryption File System) is used to encrypt a file, the file cannot be further encrypted using the encryption function of this software. ■ You can back up the fingerprint data or the information registered to Password Bank. ■ Please use Import/Export menu on Fingerprint Software Management. ■ Please also refer to the fingerprint utility Help file for more information.
Operating Basics 7. In case of finger injury or authentication failure, it is recommended that another fingerprint also be enrolled. The following message will be displayed: [We recommended enrolling at least two fingerprint images.] Click OK and repeat steps 3, 4, 5 and 6 with another finger. Windows logon via fingerprint authentication In place of the usual Windows logon by ID and password, fingerprint authentication also allows logon to Windows.
Operating Basics ■ It is necessary to register the User Password before using the fingerprint Pre-OS feature and its extended function, the fingerprint Single Sign-On feature. Please use TOSHIBA HW Setup to register the User Password. ■ If you fail fingerprint authentication more than five times, you must enter the User Password or Supervisor Password manually to start the computer. ■ When swiping, please do it slowly and at a constant speed.
Operating Basics How to enable fingerprint Single Sign-On feature It is necessary to first enroll your fingerprint with the TrueSuite Access Manager application prior to enabling and configuring the fingerprint Single Sign-On feature. Check that the fingerprint is enrolled before configuring the settings. 1. Swipe your finger across the fingerprint sensor. Or enter Windows password and click Next. 2. Click settings. 3. The Administrator Settings screen is displayed.
Operating Basics ■ The “USB Sleep and Charge function” only works for compatible ports. This function is disabled in the default setting. To enable it, you must change [Disabled] to [Enabled] in the HW setup. ■ When “USB Sleep and Charge function” is set to [Enabled] in HW Setup, USB bus power (DC5V) will be supplied to compatible ports even when the power of the computer is turned OFF. USB bus power (DC5V) is similarly supplied to the external devices which are connected to the compatible ports.
Operating Basics Using the Web Camera This section describes the bundled webcam utility, which can capture still and video images. The web camera will auto-run when Windows starts. Please unstick the protective plastic-film before using the Web Camera.
Operating Basics Capture Still Images Video Recording Audio Recording Function Display Window Camera resolution Effects 4-12 Mute Capture Still Images Click to see a preview of the captured image; you can also e-mail the image. Video Recording Click to prepare for recording. Click again to start recording. One more to stop recording and see preview of the video. Audio Recording Click to start recording, click again to stop and listen to a preview of the audio.
Operating Basics Settings Choose from the: Options tab to change the tool bar position; the Picture tab to select picture output options such as size, export file and save path; the Video tab to choose video output settings such as Frame Rate, Size, Compression and the frame rate, size, record compressor, and save path; the Audio tab to change the audio device, audio compressor, audio volume and save path. Help Displays the help files for the software.
Operating Basics Note on Use ■ TOSHIBA Face Recognition does not guarantee the correct identification of a user. Changes to the likeness of a registrant, such as hair style changes, wearing a cap, or wearing glasses may effect the recognition rates when such changes occur after the registrant had registered. ■ TOSHIBA Face Recognition may incorrectly recognize faces that are similar to a registrant. ■ For high security purposes, TOSHIBA Face Recognition is not a suitable substitute for Windows passwords.
Operating Basics 3. Click the Next button to start the guide. 4. First, take a picture while moving your neck slightly to the left and right. 5. Now take a picture while moving your neck down and up. ■ Click the Back button to practice the guide once more. 6. Click the Next button to start image-capturing process. Adjust the position of your face so that it fits within the face-shaped frame. 7. Once your face has been positioned properly, the recording will commence.
Operating Basics 2. Select a user which is deleted in the Management screen. 3. Click the Delete button. "You are about to delete the user data. Would you like to continue?" will be displayed on the screen. ■ If you do not want the data to be deleted, click the No button and you will then be returned to the Management screen. ■ Clicking on the Yes button will remove the selected user from the Management screen. How to launch the help file For further information on this utility, please refer to help file.
Operating Basics 1:1 Mode Login screen 1. 2. 3. 4. 5. 6. 7. Turn on the computer. The Select Tiles screen will be displayed. Select the tile for facial authentication. The Select Account screen will be displayed. Select the account, and click the arrow button. "Please turn your face to the camera" will be displayed. Verification will be performed. If the authentication is successful, the image data taken in step 6 will be faded in and placed over one another.
Operating Basics Loading discs To load a disc, follow the steps below and refer to the figures. 1. a. When the power is on, press the eject button to open the drawer slightly. Eject Button Pressing the eject button b. Pressing the eject button will not open the drawer when the disc drive's power is off. If the power is off, you can open the drawer by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button.
Operating Basics 2. Grasp the drawer gently and pull until it is fully opened. Pulling the drawer open 3. Place the disc, label side up, in the drawer.
Operating Basics When the drawer is fully opened, the edge of the computer will extend slightly over the disc tray. Therefore, you will need to turn the disc at an angle when you place it in the tray. After seating the disc, however, make sure it lies flat, as shown in the figure above. ■ Do not touch the laser lens. Doing so could cause misalignment. ■ Keep foreign matter from entering the drive. Check the back edge of the tray to make sure it carries no debris before closing the drive. 4.
Operating Basics Removing discs To remove the disc, follow the steps below and refer to the figure. Do not press the eject button while the computer is accessing the disc drive. Wait for the optical media drive indicator to go out before you open the drawer. Also, if the disc is spinning when you open the drawer, wait for it to stop before you remove it. 1. To pop the drawer partially open, press the eject button. Gently pull the drawer out until it is fully opened.
Operating Basics Writing CD/DVD with the DVD Super Multi drive Some models in this series are equipped with Writing CD/DVD with the DVD Super Multi drive. You can use the DVD Super Multi drive to write data to either CD-R/RW or DVD-R/-RW/+R/+RW/-RAM discs. The following applications for writing are preinstalled: TOSHIBA Disc Creator and TOSHIBA Direct Disc Writer. Ulead Movie factory for TOSHIBA.
Operating Basics DVD+RW: MITSUBISHI KAGAKU MEDIA CO, LTD. DVD-RAM: DVD Specifications for DVD-RAM Disc for Version2.0, 2.1 or 2.2 Hitachi Maxell Ltd. Matsushita Electric Industrial Co., Ltd. DVD-R for Labelflash: FUJIFILM Co. DVD+R for Labelflash: FUJIFILM Co. This drive cannot use discs that allow writing of 8 speeds or more (DVD-R, DVD+R, DVD+RW ), or 6 speeds or more (DVD-RW) ■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors may occur.
Operating Basics ■ Be sure to connect the AC adaptor before you write or rewrite. ■ Before you enter Sleep Mode/Hibernation Mode, be sure to finish DVD-RAM writing. Writing is finished if you can eject DVD-RAM media. ■ Be sure to close all other software programs except the writing software. ■ Do not run software such as a screen saver, which can put a heavy load on the CPU. ■ Operate the computer under the power scheme High Performance. Do not use power-saving features.
Operating Basics When writing or rewriting Please observe/consider the following when you write or rewrite to a CD-R/ -RW, DVD-R/-RW/-RAM or DVD+R/+RW disc. ■ Do not perform any of the following actions when writing or rewriting: ■ ■ ■ ■ ■ ■ Change users in the Windows® Vista operating system. ■ Operate the computer for any other function, including using a mouse or TouchPad or closing/opening the LCD panel. ■ Start a communication application such as a modem. ■ Apply impact or vibration to the computer.
Operating Basics TOSHIBA Disc Creator Note the following limitations when you use TOSHIBA Disc Creator: ■ DVD-Video cannot be created using TOSHIBA Disc Creator. ■ DVD-Audio cannot be created using TOSHIBA Disc Creator. ■ You cannot use the TOSHIBA Disc Creator "Audio CD" function to record music to the DVD-R/-RW or DVD+R/+RW media. ■ Do not use the "Disc Backup" function of TOSHIBA Disc Creator to copy ■ DVD-Video and DVD-ROM with copyright protection.
Operating Basics Data Verification To verify that data is written or rewritten correctly, follow the steps below before you write or rewrite a Data CD/DVD. 1. Display the setting dialog box by one of the following two steps: ■ Click the setting button ( ) for writing on the main toolbar in the Data Disc mode. ■ In the Settings menu, select Settings for Each Mode, then Data Disc. 2. Mark the Verify Written Data check box. 3. Select File Open or Full Compare mode. 4. Click the OK button.
Operating Basics Simplified steps for making a DVD-Video from adding video source: 1. Click Æ All Programs Æ DVD MovieFactory for TOSHIBA Æ Ulead DVD MovieFactory for TOSHIBA Launcher to launch DVD MovieFactory. 2. Click Video Disc Æ New Project to invoke 2nd Launcher ,choose your project type, then invoke DVD MovieFactory. 3. Add source from HD Disk by click Add video files button to invoke browser dialog box. 4. Choose the source video then go to Next page to apply Menu. 5.
Operating Basics 2. Before recording the video to DVD ■ When you record DVD disc, please use only discs recommended by the Drive manufacturer. ■ Do not set the working drive to a slow device like a USB1.1 hard disk drive or it will fail to write DVD. ■ Do not perform any of the following actions: • Operate the computer for any other function, including using a mouse to TouchPad or closing/Opening the LCD panel. • Bump or cause vibration to the computer.
Operating Basics 4. Hold the CD/DVD by its outside edge or the edge on the centre hole. Fingerprints on the surface can prevent the drive from properly reading data. 5. Do not expose to direct sunlight, extreme heat or cold. Do not place heavy objects on your CD/DVD. 6. If your CD/DVD become dusty or dirty, wipe them with a clean dry cloth. Wipe from the centre out, do not wipe in a circular direction around the CD/DVD. If necessary, use a cloth dampened in water or a neutral cleaner.
Operating Basics Properties menu Click the icon with the secondary mouse button to display properties menu on the screen. Settings You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialling Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection.
Operating Basics ■ The modular cable that comes with the computer must be used to connect a modem. Connect the end of the modular cable with the core to the computer. ■ In case of a lightning storm, unplug the modem cable from the telephone jack. ■ Do not connect the modem to a digital telephone line. A digital line will damage the modem. 1. Plug one end of the modular cable into the modem jack. 2. Plug the other end of the modular cable into a telephone jack.
Operating Basics Using the FM tuner The availability of this feature is depending on the model you purchased. 1. Plug the FM tuner antenna into the FM Antenna jack. FM Antenna jack FM TUNER ANTENNA Plug FM tuner antenna into the jack Select Start Æ All Programs Æ FM Tuner Utility to start FM software. Wireless communications The computer’s wireless communication function supports both Wireless LAN and Bluetooth devices. Only some models are equipped with both Wireless LAN and Bluetooth functions.
Operating Basics ■ Do not use the Wireless LAN (Wi-Fi) or Bluetooth functionalities near a microwave oven or in areas subject to radio interference or magnetic fields. Interference from a microwave oven or other source can disrupt Wi-Fi or Bluetooth operation. ■ Turn Wi-Fi and Bluetooth functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury.
Operating Basics Bluetooth Stack for Windows by TOSHIBA (depends on the model purchased) Please note that this software is specifically designed for the following operating systems: ■ Microsoft® Windows Vista™ Detailed information regarding the use with these operating systems is listed below. Please refer also to the electronic information which is included with each software. This Bluetooth Stack is based on Bluetooth Version 1.1/1.2/2.0+EDR specification.
Operating Basics Indicator status Indication LED off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction LED glows Wireless communication switch is on. Wireless LAN is turned on by an application. If you used the Task Bar to disable Wireless LAN, you will need to restart the computer to re-enable it. Alternatively, you can also follow this procedure: 1. In the Control Panel, click System and Maintenance. 2. Click the Device Manager.
Operating Basics Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. Disconnecting LAN cable To disconnect the LAN cable, follow the steps below. 1. Pinch the lever on the connector in the computer's LAN jack and pull out the connector. 2. Disconnect the cable from the LAN hub in the same manner. Check with your LAN administrator before disconnecting from the hub.
Operating Basics Moving the computer The computer is designed for rugged durability. However, a few simple precautions taken when moving the computer will help ensure trouble-free operation. ■ Before moving the computer, it recommends changing the function of TOSHIBA HDD Protection. Refer to the section, Using the Hard Disk Drive (HDD) Protection, in this chapter. ■ Make sure all disk activity has ended before moving the computer. Check the HDD indicator on the computer.
Operating Basics When vibration is detected, a message will be displayed on the screen, and the icon in the taskbar notification area will change to the protection state. This message is displayed until the OK button is pressed or 30 seconds pass. When vibration subsides, the icon returns to the normal state. Taskbar Icon State Icon Description Normal TOSHIBA HDD Protection is enabled. Protection TOSHIBA HDD Protection is active. The hard disk drive head is in a safe position.
Operating Basics 3D Viewer This feature displays a 3D object on the screen which moves in according to tilting or vibration of the computer. When the TOSHIBA HDD Protection detects computer vibration the Hard Disk Drive head is parked and the 3D object disk rotation will stop. When the head is un-parked the disk will begin to rotate again. The 3D Viewer can be started from the icon in the task tray. ■ This 3D object virtually represents the Computer's internal Hard Disk Drive.
Chapter 5 The Keyboard The computer's keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available.
The Keyboard F1 ... F12 function keys The function keys (not to be confused with Fn) are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. Refer to the section, Soft keys: Fn key combinations, in this chapter.
The Keyboard Press Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys. Refer to the Keypad overlay section in this chapter for more information on how to operate these keys. The power on default for both settings is off. Press Fn + F12 to lock the cursor on a specific line. The power on default is off. Hot keys + Mute:Turns the volume on and off. + Lock: Enters "Lock computer" mode.
The Keyboard + Brightness (decreases): Turns the monitor brightness down. + Brightness (increases): Turns the monitor brightness up. + Wireless: Switches the active wireless devices if the wireless communication switch is switched on. + TouchPad: Enables or disables the Touch Pad function. + Enable Keypad: Enables or disables the Key Pad function. + Number Lock: Enables or disables the Number Lock function. + Scroll Lock: Enables or disables the Scroll Lock function.
The Keyboard + TOSHIBA Zooming Utility (enlarge): Increases the icon size on the desktop or the font size within one of the supported application windows. Before using Fn+1 and Fn+2, you must install the TOSHIBA Zooming Utility. The Utility only supports the following application windows: Microsoft Internet Explorer, Microsoft Office, Windows Media Player, Adobe Reader and the icons on the desktop.
The Keyboard Keypad overlay Your computer's keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one. The keys in the centre of the keyboard with gray letters make up the numeric keypad overlay. The overlay provides the same functions as the numeric keypad on the 101/102-key enhanced keyboard described previously. Turning on the overlays The numeric keypad overlay can be used for numeric data input. Numeric mode To turn on the Numeric mode, press Fn + F11.
The Keyboard Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off. 2. Type upper-case characters by holding Fn + Shift and pressing a character key. 3. Release Fn to continue using the overlay. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation.
The Keyboard 5-8 User’s Manual
Chapter 6 Power and Power-Up Modes The computer's power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Power and Power-Up Modes Table Power conditions Power on Universal AC adaptor not connected Power off (no operation) Battery charge is • Operates above low battery • LED: Battery off trigger point Battery charge is • Operates below low battery • LED: Battery flashes orange trigger point Battery charge is exhausted Computer shuts down No Battery installed • Cannot operates • LED: Battery off Power indicators As shown in the above table, the Battery.
Power and Power-Up Modes Power indicator Check the Power indicator to determine the power status: White/Green Indicates power is being supplied to the computer and the computer is turned on. Blinking orange Indicates power is being supplied to the computer while the computer is in Sleep Mode. The indicator turns on for one second and off for two seconds. No light Under any other conditions, the indicator does not light.
Power and Power-Up Modes Battery pack To ensure that the battery pack maintains its maximum capacity, operate the computer on battery power at least once a month until the battery pack is fully discharged. Refer to Extending battery life in this chapter for procedures. If the computer is continuously operated on AC power through an AC adaptor for an extended period, more than a month, the battery may fail to retain a charge.
Power and Power-Up Modes The charge in the RTC battery is getting low or has been exhausted. You will need to set the date and time within the BIOS setup using the following steps: 1. Press F2 key - the BIOS setup screen will be displayed. 2. Set the date in System Date. 3. Set the time in System Time. 4. Press F10 key. Confirmation message will appear. Press Enter key. BIOS setup will terminate and the computer will be rebooted.
Power and Power-Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance. Safety precautions Mishandling of batteries can cause death, serious injury or property damage.
Power and Power-Up Modes 8. Never expose the battery pack to abnormal shock, vibration or pressure. The battery pack’s internal protective device will fail, causing it to overheat, explode, ignite or leak caustic liquids possibly resulting in death or serious injury. 9. Never let a battery pack become wet. A wet battery pack will overheat, ignite or rupture possibly resulting in death or serious injury. Warning 1.
Power and Power-Up Modes 6. Be sure to monitor the remaining battery power. If the battery pack and real time clock battery discharge completely, Sleep Mode will not function and data in memory will be lost. Also, the computer might register an incorrect time and date. In this case, connect the AC adaptor to recharge the batteries. 7. Never install or remove the battery pack without first turning off the power and disconnecting the AC adaptor.
Power and Power-Up Modes Time The following table shows the approximate time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off Battery pack (3cell, 6cell, 9cell) 4-10 hours 4 hours max RTC Battery About 24 hours About 24 hours The charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the computer.
Power and Power-Up Modes Monitoring battery capacity Remaining battery power can be monitored using the following methods. ■ Clicking the battery icon on the task bar ■ Via the Windows Mobility Center window ■ Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time.
Power and Power-Up Modes Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods. Battery pack (3cell, 6cell, 9cell) Approximately 1.
Power and Power-Up Modes Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. The life of the battery pack is generally about 500 recharges. If the Battery indicator flashes orange shortly after fully recharging the battery, the battery pack needs to be replaced. You might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source.
Power and Power-Up Modes Installing the battery pack To install a battery, follow the steps below. ■ The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Do not touch the latch while holding the computer. Or you may get injured by the dropped battery by unintentional release of the latch. 1. 2. 3. 4.
Power and Power-Up Modes At this point, the hotkeys Fn + F1 to F9 do not work. They will function after you enter the password. 2. Enter the password. 3. Press Enter. If you enter the password incorrectly three times in a row, the computer shuts off. In this case, you must turn the computer back on to retry password entry. Power-up modes The computer has the following power-up modes: ■ Boot Mode: Computer shuts down without saving data. Always save your work before you turn the computer off in boot mode.
Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer. TOSHIBA HW Setup lets you configure settings for General, Password, Display, Boot Priority, Keyboard, LAN, and USB. Accessing HW Setup To run HW Setup, click , All Programs, TOSHIBA, Utilities, HWSetup. HW Setup Window The HW Setup window contains the following tabs: General, Password, Display, Boot Priority, Keyboard, USB and LAN .
HW Setup Password This tab allows you to set or reset the user password for power on. User Password Lets you register a new password or un-register an existing password. Not Registered Un-registers an existing password Registered Register a new password by following the on screen instructions Owner String This blank field is used to display a message when the password field is displayed on startup. If a password is not registered the message will not be shown. The maximum length is 256 characters.
HW Setup Keyboard Wake-up on Keyboard When this feature is enabled and the computer is in Sleep Mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in Sleep Mode. Enabled Enables the Wake-up on Keyboard function. Disabled Disables the Wake-up on Keyboard function (Default). USB USB Keyboard/Mouse/FDD Legacy Emulation Use this option to enable or disable Legacy USB support.
HW Setup 7-4 User’s Manual
Chapter 8 Optional Devices Optional devices can expand the computer's capabilities and its versatility.
Optional Devices ExpressCard Slot The computer is equipped with a ExpressCard slot that can accommodate one ExpressCard. Inserting an ExpressCard One ExpressCard connector is located on the left side of the computer. The computer's hot-install feature lets you install ExpressCard while the computer's power is on. To install an ExpressCard, follow the steps below. 1. Insert the ExpressCard. 2. Press gently to ensure a firm connection.
Optional Devices Removing an ExpressCard ■ Before removing an ExpressCard, make sure that any applications or system services do not use the card. ■ Be sure to disable the ExpressCard prior to removing it. Otherwise, the system may be fatally damaged. To remove the ExpressCard, follow the steps below. 1. Click the Safety Remove Hardware icon on the Task Bar. 2. Click the ExpressCard you want to remove. 3. Press the ExpressCard once to extend it. 4. Grasp the extended ExpressCard, and remove it.
Optional Devices SD/SDHC/MMC/MEMORY STICK / MEMORY STICK PRO/xD Memory cards The computer is equipped with a multiple digital media card slot that can accommodate SD/SDHC/MMC/MEMORY STICK/MEMORY STICK PRO/ xD memory cards. These memory cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, which use flash-memory.
Optional Devices Installing a memory card To install a memory card: 1. Insert the memory card. 2. Press gently to ensure a firm connection. Inserting a memory card Be sure the memory card is oriented properly before you insert it. If Windows® fails to read the card, remove it then re-insert it. ■ The multiple digital media card slot only accepts one type of card at a time. Do not attempt to install more than one card as you risk damaging either the cards themselves or the computer.
Optional Devices ■ Make sure the memory card indicator is out before you remove the card or turn off the computer's power. If you remove the card or turn off the power while the computer is accessing the card you may lose data or damage the card. ■ Do not remove the card while the computer is in Sleep or Hibernation mode. The computer could become unstable or data in the memory card could be lost.
Optional Devices Memory expansion You can install additional memory in the computer's memory module socket to increase the amount of RAM. This section describes how to install and remove a memory module. ■ Use only memory modules approved by TOSHIBA. ■ Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module. Also, data will be lost. a. The computer is turned on. b. The computer was shut down using the Sleep Mode or Hibernation Mode.
Optional Devices Memory Module Cover Removing the memory module cover 6. Lift one side of the insulator sheet and fit the module's connectors into the computer's connectors at about a 45 degree angle. Press the module carefully to ensure a firm connection. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. Slot A is reserved for main memory. Use slot B for expanded memory. If only one card is installed use slot A. 7.
Optional Devices 8. Seat the cover and secure it with the screws. 9. Replace the battery pack as described in Chapter 6, Power and PowerUp Modes. 10. Turn the power on and make sure the added memory is recognized. Open System in the Control Panel and click the General tab. Points to note about memory module error If you install a memory module that is not compatible with the computer, the Power indicator will flash (on for 0.5 seconds, off for 0.
Optional Devices Latches 1 2 1 Removing the memory module 6. Seat the cover and secure it with screws and replace the battery pack. Additional battery pack You can increase the portability of the computer with additional battery packs. If you’re away from an AC power source and your battery runs low, you can replace it with a freshly charged battery. Refer to Chapter 6, Power and Power-Up Modes.
Optional Devices External monitor An external analog monitor can be connected to the external monitor port on the computer. Refer to Appendix B, Display Controller and Modes. The computer supports several video modes. To connect a monitor, follow the steps below. 1. Turn the computer off. 2. Connect the monitor to the external monitor port. 3. Turn the monitor's power on. 4. Turn the computer on. When you turn on the power, the Windows® Bootup screen (Windows® Logo) appears on the display device.
Optional Devices 2. Plug the other end of the HDMI cable into the HDMI out port on your computer. Setting for display video on HDMI To view video on the HDMI device, be sure to configure the following settings otherwise you may find that nothing is displayed. ■ Be Sure to use the FN + F5 hot keys to select the display device before starting to play video. Do not change the display device while playing video. ■ Do not change the display device under the following conditions.
Optional Devices Precautions 1. Make a back-up of your data before transferring it to the computer. There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. 2. Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise. Data can be destroyed. 3.
Optional Devices Disconnecting 1. Open the Safety Remove Hardware icon on the Task Bar. 2. Point to i.LINK (IEEE1394) device and click. 3. Disconnect the cable from the computer then from the i.LINK device. Refer also to the documentation that came with your i.LINK device. eSATA (External Serial ATA) An device corresponding to eSATA function can be connected to the eSATA/USB combo port on the computer. Connecting an eSATA device To connect an eSATA device, follow the steps as detailed below: 1.
Optional Devices Disconnecting an eSATA device When you have finished using an eSATA device, you can follow the procedures below in order to disconnect it: 1. Wait for the indicator light of an eSATA device to go out to make sure all activity has stopped. If you disconnect an eSATA device or turn off the power while the computer is accessing the drive you may lose data or damage an eSATA device or the drive. 2. Click the Safely Remove Hardware icon on the Windows Taskbar. 3.
Optional Devices 8-16 User’s Manual
Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists. Further action may result in data loss or damage.
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer and any other external device you are using. ■ Before you attach an external device, turn the computer off. When you turn the computer back on it recognizes the new device.
Troubleshooting Software The problems may be caused by your software or disc. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation. These documents usually include a problem solving section or a summary of error messages. Next, check any error messages in the operating system documentation.
Troubleshooting Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: TOSHIBA Leading Innovation >>> This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program.
Troubleshooting AC power If you have trouble turning on the computer with the AC adaptor connected, check the Battery indicator. Refer to Chapter 6, Power and Power-Up Modes for more information. Problem Procedure AC adaptor doesn’t power the computer Check the connections. Make sure the cord is firmly connected to the computer and a power outlet. Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it.
Troubleshooting Problem Procedure Unplug the AC adaptor and remove the battery to make sure the terminals are clean. If necessary wipe them with a soft dry cloth dipped in alcohol. Connect the AC adaptor and replace the battery. Make sure it is securely seated. Check the Battery indicator. If it does not glow, let the computer charge the battery for at least 20 minutes.
Troubleshooting ■ Reformatting the media ■ Reinstalling an operating system from the recovery CD-ROM The procedures above delete only the initial part of the data used for file management. This makes the file invisible to the operating system, but the data can still be read by specialized utilities. If you dispose of the PC, please delete all the data on its hard disk drive. Doing so prevents unauthorized use of such data.
Troubleshooting LCD panel Apparent LCD problems may be related to the computer's setup. Problem Procedure No display Press hot keys Fn + F5 to change the display priority, to make sure it is not set for an external monitor. Problems above remain Refer to your software’s documentation to unresolved or other determine if the software is causing the difficulty. problems occur Run the diagnostic test. Contact your dealer if the problems continue.
Troubleshooting Recovery Discs Problem Procedure The following message appears when executing Recovery Disc Creator. "The Recovery Disc Creator can not be launched because there is no recovery partition." You will see this message if you have previously chosen to remove the partition and are trying to create "Recovery Media". When there is no recovery partition, the Recovery Disc Creator cannot make Recovery Media.
Troubleshooting Problem Procedure The software or hardware configuration may be Some CD/DVDs run correctly, but others do causing a problem. Make sure the hardware configuration matches your software's needs. not Check the CD/DVD documentation. Check the type of CD/DVD you are using.
Troubleshooting Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. TouchPad Problem Procedure On-screen pointer does The system might be busy. If the pointer is not respond to Pad shaped as an hourglass, wait for it to return to its operation normal shape and try again to move it. Double-tapping does not work Try changing the double-click speed setting in the mouse control utility. 1.
Troubleshooting USB mouse Problem Procedure On-screen pointer does The system might be busy. If the pointer is not respond to mouse shaped as an hourglass, wait for it to resume its operation normal shape and try again to move it. Make sure the mouse is properly connected to the USB port. Double-clicking does not work Try changing the double-click speed setting in the mouse control utility. 1. To access this utility, click , Control Panel, Hardware and Sound, then Mouse icon. 2.
Troubleshooting USB Sleep and Charge function Problem Procedure I cannot use the “USB Sleep and Charge function”. The setting of “USB Sleep and Charge function” may be [Disabled]. Change the setting to [Enabled] in the HW Setup. When there is a current overflow of the external device connected to the compatible port, USB bus power (DC5V) supply may be stopped for safety reasons. When this happens, disconnect an external device if some external devices are connected.
Troubleshooting Problem Procedure External devices connected to the compatible ports do not work when connected to a compatible port. Some external devices may not work when connected to a compatible port when the “USB Sleep and Charge function” is [Enabled] in the HW Setup. Reconnect the external device after turning ON the computer.
Troubleshooting Problem Procedure No sound is heard Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not turn on Make sure that the external monitor’s power switch is on. Confirm that the external monitor’s power cable is plugged into a working power outlet.
Troubleshooting Problem Procedure Communication is cut off unexpectedly The computer will automatically cut off communication when connection with the carrier is not successful for a set time interval. Try lengthening this time interval. A CONNECT display is Check the error control setting in your quickly replaced by NO communications application. CARRIER You can also use the AT\N command.
Troubleshooting Fingerprint Sensor Problem Procedure Reading of the fingerprint was not successful Please try again using the correct posture. Refer to Using the fingerprint sensor in Chapter 4, Operating Basics. Try the recognition process again using another enrolled finger. The fingerprint cannot be read due to injuries to the finger Try the recognition process again using another enrolled finger.
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first. Before contacting TOSHIBA, try the following: ■ Review troubleshooting sections in the documentation for software and peripheral devices.
Troubleshooting User’s Manual Outside of Europe In Europe Singapore TOSHIBA Singapore Pte. Ltd. 438B Alexandra Road #06-01 Alexandra Technopark Singapore 119968 Spain TOSHIBA Information Systems, ESPAÑA Parque Empresarial San Fernando Edificio Europa, la Planta, Escalera A 28830 Madrid United States of America TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 USA United Kingdom TOSHIBA Information Systems (U.K.) Ltd.
Troubleshooting 9-20 User’s Manual
Appendix A Specifications This appendix summarizes the computer's technical specifications.
Specifications Communication specifications Communication System Data: Fax: Communication protocol Data ITU-T-Rec (Former CCITT) Bell Fax: ITU-T-Rec (Former CCITT) Communication Speed A-2 Full duplex Half duplex V.21/V.22/V.22bis/V.32/ V.32bis/V.34/V.90/V.92 103/212A V.17/V.29/V.27ter/V.21 ch2 Data transmission and reception 300/1200/2400/4800/7200/9600/12000/14400/ 16800/19200/21600/24000/26400/28800/31200/ 33600 bps Data reception only with V.
Specifications User’s Manual Transmitting level -10 dBm Receiving level -10 to -40 dBm Input/output impedance 600 ohms ±30% Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.42bis Power supply +3.
Specifications A-4 User’s Manual
Appendix B Display Controller Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA) and Extended Graphics Array (XGA) support for the internal LCD and external monitors. A high-resolution external monitor connected to the computer can display up to 2048 horizontal and 1536 vertical pixels at up to 16M colors.
Display Controller B-2 User’s Manual
Appendix C Wireless LAN Card Specifications Form Factor Mini PCI TypeIII Compatibility ■ IEEE 802.11 Standard for Wireless LANs ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The "Wi-Fi CERTIFIED" logo is a certification mark of the Wi-Fi Alliance. Network Operating System ■ Microsoft® Windows® Networking Media Access Protocol ■ CSMA/CA (Collision Avoidance) with Acknowledgement (ACK) Data Rate ■ 54/48/36/24/18/12/9/6 Mb/s (IEEE 802.11a/g) ■ 11/5.5/2/1 Mb/s (IEEE 802.
Wireless LAN Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Wireless LAN Supported Frequency Sub-bands Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions. Wireless IEEE 802.11 Channels Sets (Revision B, G and draft N) Frequency Range Channel ID 2400-2483.
Wireless LAN C-4 User’s Manual
Appendix D AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 1.7 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
AC Power Cord and Connectors In Europe, power cords must be VDE type, H05VVH2-F and two conductor. For the United States and Canada, plug configuration must be a 2-15P (250 V) or 1-15P (125 V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe.
Appendix E Legal Footnotes This chapter states the Legal Footnotes information applicable to TOSHIBA computers. In the text in this manual, *XX is used to show which Legal Footnotes description is related to TOSHIBA computers. Description(s) related to this computer are marked with a blue *XX in this manual. Clicking on *XX will display the related description. Non-applicable Icons Certain computer chassis are designed to accommodate all possible configurations for an entire product series.
Legal Footnotes ■ use of computer at temperatures outside the range of 5°C to 30°C (41°F to 86°F) or >25°C (77°F) at high altitude (all temperature references are approximate and may vary depending on the specific computer model please refer to your computer documentation or visit the TOSHIBA website at http://www.pcsupport.toshiba.com for details). CPU performance may also vary from specifications due to design configuration. Under some conditions, your computer product may automatically shutdown.
Legal Footnotes Battery Life Battery life may vary considerably depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the design of individual components. Published battery life numbers are achieved on select models and configurations tested by TOSHIBA at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
Legal Footnotes Wireless LAN The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. [54Mbps is the theoretical maximum speed under the IEEE802.11 (a/b/g) standard.] The actual transmission speed will be lower than the theoretical maximum speed.
Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Glossary HDMI-CEC: high definition multimedia interface consumer electronics control IDE: integrated drive electronics IEEE: Institute of Electrical and Electronics Engineers IMSM: Intel Matrix Storage Manager I/O: input/output IRQ: interrupt request KB: kilobyte LAN: local area network LCD: liquid crystal display LED: light emitting diode MB: megabyte MMC: multi media card OCR: optical character recognition (reader) PC: personal computer PCI: peripheral component interconnect RAM: random access memory RGB
Glossary alphanumeric: Keyboard characters including letters, numbers and other symbols, such as punctuation marks or mathematical symbols. alternating current (AC): Electric current that reverses its direction of flow at regular intervals. analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals.
Glossary C: cache memory: A section of very fast memory in which frequently used information is duplicated for quick access. Accessing data from cache is faster than accessing it from the computer's main memory. See also L1 cache, L2 cache. capacity: The amount of data that can be stored on a magnetic storage device such as a floppy diskette or hard disk drive.
Glossary computer program: A set of instructions written for a computer that enable it to achieve a desired result. computer system: A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information. configuration: The specific components in your system (such as the terminal, printer, and disk drives) and the settings that define how your system works. You use the HW Setup program to control your system configuration.
Glossary documentation: The set of manuals and/or other instructions written for the users of a computer system or application. Computer system documentation typically includes procedural and tutorial information as well as system functions. double click: To press and release the pointing device's primary button rapidly twice without moving the pointing device. In the Windows® operating system, this refers to the pointing device's left button, unless otherwise stated.
Glossary fingerprint sensor: The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint. firmware: A set of instructions built into the hardware which controls and directs a microprocessor’s activities. flash memory: Non-volatile memory that can be written to as well as read. Information in flash memory remains whether or not the computer is receiving power. This type of memory is used to retain your fingerprint data. See also memory. Compare RAM and ROM.
Glossary icon: A small graphic image displayed on the screen or in the indicator panel. In Windows, an icon represents an object that the user can manipulate. i.LINK (IEEE1394): This port enables high-speed data transfer directly from external devices such as digital video cameras. input: The data or instructions you provide to a computer, communication device or other peripheral device from the keyboard or external or internal storage devices.
Glossary Liquid Crystal Display (LCD): Liquid crystal sealed between two sheets of glass coated with transparent conducting material. The viewing-side coating is etched into character forming segments with leads that extend to the edge of the glass. Applying a voltage between the glass sheets. M: main board: See motherboard. megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also kilobyte. megahertz: A unit of wave frequency that equals 1 million cycles per second. See also hertz.
Glossary O: OCR: Optical Character Recognition (reader). A technique or device that uses laser or visible light to identify characters and input them into a storage device. online state: A functional state of a peripheral device when it is ready to receive or transmit data. operating system: A group of programs that controls the basic operation of a computer.
Glossary Power Saver: A TOSHIBA utility that lets you set the parameters for various power-saving functions. program: A set of instructions a computer can execute that enables it to achieve a desired result. See also application. prompt: A message the computer provides indicating it is ready for or requires information or an action from you. R: Radio frequency interference (RFI) shield: A metal shield enclosing the printed circuit boards of the printer or computer to prevent radio and TV interference.
Glossary serial: Processes that occur one at a time. In communications, it means the transmission of one bit at a time sequentially over a single channel. On your computer, the serial port provides a serial interface between the computer and an appropriate device. Compare parallel. SIO: Serial Input/Output. The electronic methodology used in serial data transmission.
Glossary window: A portion of the screen that can display its own application, document or dialog box. Often used to mean a Microsoft Windows window. Wireless LAN: Local Area Network (LAN) through wireless communication. Wireless WAN: Wide Area Network (WAN) through wireless communication. write protection: A method for protecting a floppy diskette from accidental erasure.
Glossary Glossary-14 User’s Manual
Index A Display controller, B-1 AC adaptor, 1-4 additional, 1-15 connecting, 3-3 ASCII characters, 5-7 E Equipment checklist, 1-1 B Floppy disk using, 4-17 Fn + Esc (sound mute), 5-3 Fn + F1 (instant security), 5-3 Fn + F2 (power save mode), 5-3 Fn + F3 (Sleep Mode), 5-3 Fn + F4 (hibernation), 5-3 Fn + F5 (display selection), 5-3 Fn + F6 (Display Brightness decreases), 5-4 Fn + F7 (Display Brightness increases), 5-4 Fn + F8 (Wireless setting), 5-4 Fn + F9 (Touch Pad), 5-4 Fn Sticky key, 5-5 Function ke
Index K Keyboard, 1-6, 5-1 emulating keys on enhanced, 5-2 F1 ...
Index Processor, 1-3 R Restarting the computer, 3-9 S Security lock attaching, 8-15 Sleep Mode, 1-10 setting, 3-6 System automatic, 1-9 Soft keys emulating keys on enhanced keyboard, 5-2 ScrLock, 5-3 Sound System, 1-7, 4-30 headphone jack, 1-7 microphone jack, 1-7 mute hot keys, 5-3 T TOSHIBA ConfigFree, 1-14 TOSHIBA Disc Creator, 1-13 Touch Pad, 1-6 location, 2-7 using, 4-1 U USB, 1-6 V Video modes, B-1 Video RAM, 1-3 W Wireless communication switch, 4-35 indicator, 4-35 Wireless LAN, 1-8 using, 4-3
Index Index-4 User’s Manual
