Owner's Manual

ManualsBrandsToyota ManualsAutomobileToyota 2005 Toyota YARIS

TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS

1 of 10

1 egaP GNIMMARGORP METSYS PIVT ATOYOT

PROGRAMMING TABLE OF CONTENTS

EGAP GNIMMARGORP 0023SR

ADD ADDITIONAL REMOTE CONTROL(S) TO SYSTEM 2, 3

REPROGRAM EXISTING REMOTE CONTROLS 4, 5

REMOTE CONTROL FUNCTION SELECT 6, 7

CLEAR ALL REMOTE CONTROL CODES 8

PASSIVE ARMING ON/ OFF SELECTION AND 9

ENTRY DELAY TIME SELECTION

IGNITION−CONTROLLED AUTOMATIC DOOR 10

LOCK/ UNLOCK

Notes:

For factory remote keyless entry system programming information, refer to the

vehicle’s repair manual.

Refer to the RS3000 Owner’s guide for RS3000 feature programming.

Summary of content (10 pages)

PAGE 1
TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS TOYOTA TVIP SYSTEM PROGRAMMING Page 1 PROGRAMMING TABLE OF CONTENTS RS3200 PROGRA MMING PA GE ADD ADDITIONAL REMOTE CONTROL(S) TO SYSTEM 2, 3 REPROGRAM EXISTING REMOTE CONTROLS 4, 5 REMOTE CONTROL FUNCTION SELECT 6, 7 CLEAR ALL REMOTE CONTROL CODES 8 PASSIVE ARMING ON/ OFF SELECTION AND ENTRY DELAY TIME SELECTION 9 IGNITION−CONTROLLED AUTOMATIC DOOR LOCK/ UNLOCK 10 Notes: For factory remote keyless entry system programming information, refe
PAGE 2
TVIP V3 RS3200 Page 2 SYSTEM PROGRAMMING INSTRUCTIONS TOYOTA TVIP SYSTEM PROGRAMMING−RS3200 ADD ADDITIONAL REMOTE CONTROL(S) TO SYSTEM Follow this procedure to add additional remote controls to a system. The RS3200 may be programmed to operate with a maximum of four remote controls.
PAGE 3
TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS TOYOTA TVIP SYSTEM PROGRAMMING Page 3 ADD ADDITIONAL REMOTE CONTROL(S) TO SYSTEM (continued) 3. Program (add) an additional remote control. a. Press and release b. Press and release c. The tail and marker lights flash 1 time, both the LOCK and the buzzer chirps 1 time, and the doors the LOCK button. UNLOCK buttons lock and unlock 1 time. * on one remote control at the same time. Note: Repeat the above steps to add additional remote controls. 4.
PAGE 4
TVIP V3 RS3200 Page 4 SYSTEM PROGRAMMING INSTRUCTIONS TOYOTA TVIP SYSTEM PROGRAMMING−RS3200 REPROGRAM EXISTING REMOTE CONTROLS Follow this procedure to clear all existing remote control codes and reprogram existing remote controls to a system.
PAGE 5
TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS TOYOTA TVIP SYSTEM PROGRAMMING Page 5 REPROGRAM EXISTING REMOTE CONTROLS (continued) 3. Reprogram an existing remote control. a. Press and release c. The tail and marker lights flash 1 time, the b. Press and release both the LOCK and buzzer chirps 1 time, and the doors lock the LOCK button. UNLOCK buttons and unlock 1 time. * on one remote control at the same time. Note: Repeat the above steps to program (add) additional remote controls. 4.
PAGE 6
TVIP V3 RS3200 Page 6 SYSTEM PROGRAMMING INSTRUCTIONS TOYOTA TVIP SYSTEM PROGRAMMING−RS3200 REMOTE CONTROL FUNCTION SELECT Follow this procedure to change the operating functions of remote controls already programmed into a system. You may change the remote control’s default unlock operation mode so that pressing the UNLOCK button once causes all doors to unlock at the same time. Also, you may activate the AUX button function on 4 button remote controls. 1.
PAGE 7
TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS TOYOTA TVIP SYSTEM PROGRAMMING Page 7 REMOTE CONTROL FUNCTION SELECT (continued) 3. Select the operating functions for an existing remote control. a. Press and release both the LOCK and UNLOCK buttons on one remote control at the same time. b. Select one of the following modes: Press and release the LOCK button to select double unlock function (press the UNLOCK button twice to unlock all the doors.
PAGE 8
TVIP V3 RS3200 Page 8 SYSTEM PROGRAMMING INSTRUCTIONS TOYOTA TVIP SYSTEM PROGRAMMING−RS3200 CLEAR ALL REMOTE CONTROL CODES Follow this procedure to clear all remote controls programmed to operate the system. Please note, if you have remote controls to program into the system and you want to first clear all existing remote controls from the system, follow the reprogram procedure as shown on pages 4 and 5. 1. Before you begin: Open the driver’s door and remove the key from the ignition switch. 2.
PAGE 9
TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS TOYOTA TVIP SYSTEM PROGRAMMING Page 9 PASSIVE ARMING ON/ OFF SELECTION AND ENTRY DELAY TIME SELECTION The RS3200 is factory set to not passively arm. To change the system’s operation for passive arming, as well as to adjust the entry delay time, follow the procedure below. 1. Before you begin: Close all the doors and the trunk or hatch, unlock all the doors with the inside lock switch, then remove the key from the ignition switch. 2.
PAGE 10
TVIP V3 Page 10 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS TOYOTA TVIP SYSTEM PROGRAMMING−RS3200 IGNITION−CONTROLLED AUTOMATIC DOOR LOCK/ UNLOCK When all doors are closed, the RS3200 is factory set to automatically lock the vehicle’s door when the ignition key is turned to ON or START, and unlock them (open or not) when the key is turned back to ACC or LOCK. Follow the procedure below to change this feature’s operation mode. 1.