TL-WR841N TL-WR841ND 300Mbps Wireless N Router REV7.0.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES CO., LTD.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
Industry Canada Statement Complies with the Canadian ICES-003 Class B specifications. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Korea Warning Statements 당해 무선설비는 운용중 전파혼신 가능성이 있음.
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 300Mbps Wireless N Router Model No.
CONTENTS Package Contents .................................................................................................................................... 1 Chapter 1. Introduction.......................................................................................................................... 2 1.1 Overview of the Router ......................................................................................................... 2 1.2 Conventions .................................................
4.6.5 4.7 Guest Network .................................................................................................................... 45 4.7.1 4.8 4.9 Wireless Statistics ................................................................................................... 44 Wireless Settings .................................................................................................... 45 DHCP ..................................................................................................
4.15.2 ARP List .................................................................................................................. 77 4.16 Dynamic DNS ...................................................................................................................... 78 4.16.1 Comexe.cn DDNS .................................................................................................. 78 4.16.2 Dyndns.org DDNS ............................................................................................
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Package Contents The following items should be found in your package: TL-WR841N/TL-WR841ND 300Mbps Wireless N Router DC Power Adapter for TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Quick Installation Guide Ethernet Cable Resource CD for TL-WR841N/TL-WR841ND 300Mbps Wireless N Router, including: • This Guide • Other Helpful Information Note: Make sure that the package contains the above items.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Chapter 1. Introduction 1.1 Overview of the Router The TL-WR841N/TL-WR841ND 300Mbps Wireless N Router integrates 4-port Switch, Firewall, NAT-Router and Wireless AP. The 300Mbps Wireless N Router delivers exceptional range and speed, which can fully meet the need of Small Office/Home Office (SOHO) networks and the users demanding higher networking performance.
TL-WR841N/TL-WR841ND 1.2 300Mbps Wireless N Router Conventions The router or TL-WR841N/TL-WR841ND mentioned in this guide stands for TL-WR841N/TL-WR841ND 300Mbps Wireless N Router without any explanation. Note: The two devices of TL-WR841N and TL-WR841ND are sharing this User Guide. For simplicity, we will take TL-WR841ND for example throughout this Guide. The differences between them are: TL-WR841N router with 2 fixed antennas. TL-WR841ND router with 2 detachable antennas. 1.
TL-WR841N/TL-WR841ND 1.4 1.4.1 300Mbps Wireless N Router Panel Layout The Front Panel Figure 1-1 Front Panel sketch The router’s LEDs are located on the front panel (View from left to right). Name （Power） (WLAN) (LAN 4-1) (WAN) (WPS) Status Indication Off Power is off. On The router has finished booting. Flash The router is booting or upgrading. Off The Wireless function is disabled. On The Wireless function is enabled. Off There is no device linked to the corresponding port.
TL-WR841N/TL-WR841ND 1.4.2 300Mbps Wireless N Router The Rear Panel Figure 1-2 Rear Panel sketch The following parts are located on the rear panel (View from left to right). ON/OFF: The switch for the power. POWER: The Power socket is where you will connect the power adapter. Please use the power adapter provided with this TL-WR841ND 300Mbps Wireless N Router. WAN: This WAN port is where you will connect the DSL/cable Modem, or Ethernet.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Chapter 2. Connecting the Router 2.1 System Requirements Broadband Internet Access Service (DSL/Cable/Ethernet) One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the router is connected directly to the Ethernet.) PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors TCP/IP protocol on each PC Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari 2.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Figure 2-1 Hardware Installation 5. Verify that the hardware connection is correct by checking these LEDs.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Note: The diameter of the screw ranges from 3.5 mm to 8 mm, and the distance between two screws is 123 mm. The screw that projects from the wall needs around 4.5 mm base, and the length of the screw needs to be at least 20 mm to withstand the weight of the product.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functions of your TL-WR841ND 300Mbps Wireless N Router using Quick Setup Wizard within minutes. 3.1 TCP/IP Configuration The default domain name of the TL-WR841ND 300Mbps Wireless N Router is http://tplinkwifi.net, the default IP address is 192.168.0.1, and the default Subnet Mask is 255.255.255.0. These values can be changed as you desire.
TL-WR841N/TL-WR841ND Figure 3-1 300Mbps Wireless N Router Success result of Ping command If the result displayed is similar to the Figure 3-2, it means the connection between your PC and the router is failed. Figure 3-2 Failure result of Ping command Please check the connection following these steps: 1. Is the connection between your PC and the router correct? Note: The 1/2/3/4 LEDs of LAN ports which you link to on the router and LEDs on your PC's adapter should be lit. 2.
TL-WR841N/TL-WR841ND 3. 300Mbps Wireless N Router Is the default LAN IP of the router correct? Note: If the LAN IP of the modem connected with your router is 192.168.0.x, the default LAN IP of the router will automatically switch from 192.168.0.1 to 192.168.1.1 to avoid IP conflict. Therefore, in order to verify the network connection between your PC and the router, you can open a command prompt, and type ping 192.168.1.1, and then press Enter. 3.
TL-WR841N/TL-WR841ND Figure 3-5 300Mbps Wireless N Router Quick Setup Note: The Router will automatically detect the Internet connection. If the Internet is available, the Router will direct you to step 5 Wireless settings; otherwise, you need to continue with step 3 to choose WAN Connection Type. 3. Click Next, and then WAN Connection Type page will appear, shown in Figure 3-6.
TL-WR841N/TL-WR841ND 4. 300Mbps Wireless N Router If you select Auto-Detect, the router will automatically detect the connection type your ISP provides. Make sure the cable is securely plugged into the Internet port before detection. The appropriate configuration page will be displayed when an active Internet service is successfully detected by the router. 1） If the connection type is Dynamic IP, there will appear the MAC Clone page (as shown in Figure 3-7).
TL-WR841N/TL-WR841ND Figure 3-8 300Mbps Wireless N Router Quick Setup - Static IP IP Address - This is the WAN IP address as seen by external users on the Internet (including your ISP). Enter the IP address into the field. Subnet Mask - The Subnet Mask is used for the WAN IP address, it is usually 255.255.255.0. Default Gateway - Enter the gateway IP address into the box if required. Primary DNS - Enter the DNS Server IP address into the box if required.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Confirm Password - Re-enter the password provided by your ISP to ensure the Password you entered is correct. Check the radio button of Dynamic/Static IP to activate the secondary connection if your ISP provides an extra Connection type such as Dynamic/Static IP to connect to a local area network. 4） If the connection type is L2TP/Russian L2TP, the next screen will appear as shown in Figure 3-10.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router 5） If the connection type is PPTP/Russian PPTP, the next screen will appear as shown in Figure 3-11. Configure the following parameters and then click Next to continue. Figure 3-11 Quick Setup – PPTP User Name and Password - Enter the User Name and Password provided by your ISP. These fields are case sensitive. If you have difficulty with this process, please contact your ISP.
TL-WR841N/TL-WR841ND 5. 300Mbps Wireless N Router Click Next to continue, the Wireless settings page will appear as shown in Figure 3-12. Figure 3-12 Quick Setup – Wireless Wireless Radio - Enable or disable the wireless radio. Wireless Network Name - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the router without encryption. It is recommended strongly that you choose one of following options to enable security. WPA/WPA2-Personal - Select WPA based on pre-shared passphrase. PSK Password - You can enter ASCII or Hexadecimal characters.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Chapter 4. Configuring the Router This chapter will show each Web page's key functions and the configuration way. 4.1 Login After your successful login, you will see the main menus on the left of the Web-based utility. On the right, there are the corresponding explanations and instructions. The detailed explanations for each Web page’s key function are listed below. 4.2 Status The Status page provides the current status information about the router.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Figure 4-1 Router Status 4.3 Quick Setup Please refer to 3.2 Quick Installation Guide. 4.4 WPS This section will guide you to add a new wireless device to an existing network quickly by WPS (Wi-Fi Protected Setup) function. a). Choose menu “WPS”, and you will see the next screen (shown in Figure 4-2 ).
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Figure 4-2 WPS WPS Status - Enable or disable the WPS function here. Current PIN - The current value of the router's PIN is displayed here. The default PIN of the router can be found in the label attached on the router. Restore PIN - Restore the PIN of the router to its default. Gen New PIN - Click this button, and then you can get a new random value for the router's PIN. You can ensure the network security by generating a new PIN.
TL-WR841N/TL-WR841ND Figure 4-3 300Mbps Wireless N Router Add A New Device Step 2: Press and hold the WPS button of the client device directly. Step 3: The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup process. Step 4: When the WPS LED is on, the client device has successfully connected to the router. Step 5: Refer back to your client device or its documentation for further instructions. II.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Note: 1) The WPS LED on the router will light green for five minutes if the device has been successfully added to the network. 2) The WPS function cannot be configured if the Wireless Function of the router is disabled. Please make sure the Wireless Function is enabled before configuring the WPS. 4.5 Network Figure 4-5 the Network menu There are three submenus under the Network menu (shown in Figure 4-5): WAN, MAC Clone, and LAN.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router This page displays the WAN IP parameters assigned dynamically by your ISP, including IP address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP parameters from your ISP. Click the Release button to release the IP parameters. MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU Size unless required by your ISP.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Default Gateway - (Optional) Enter the gateway IP address in dotted-decimal notation provided by your ISP. MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU Size unless required by your ISP. Primary/Secondary DNS - (Optional) Enter one or two DNS addresses in dotted-decimal notation provided by your ISP.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Disabled - The Secondary Connection is disabled by default, so there is PPPoE connection only. This is recommended. Dynamic IP - You can check this radio button to use Dynamic IP as the secondary connection to connect to the local area network provided by ISP. Static IP - You can check this radio button to use Static IP as the secondary connection to connect to the local area network provided by ISP.
TL-WR841N/TL-WR841ND Figure 4-9 300Mbps Wireless N Router PPPoE Advanced Settings MTU Size - The default MTU size is “1480” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP. Service Name/AC Name - The service name and AC (Access Concentrator) name, which should not be configured unless you are sure it is necessary for your ISP. In most cases, leaving these fields blank will work.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Figure 4-10 WAN – BigPond Cable User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Auth Server - Enter the authenticating server IP address or host name. Auth Domain - Type in the domain suffix server name based on your location. e.g. NSW / ACT - nsw.bigpond.net.au VIC / TAS / WA / SA / NT - vic.bigpond.net.au QLD - qld.bigpond.net.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Connect Automatically - The connection can be re-established automatically when it was down. Connect Manually - You can click the Connect/Disconnect button to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect on Demand mode. The Internet connection can be disconnected automatically after a specified inactivity period and re-established when you attempt to access the Internet again.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Dynamic IP/ Static IP - Choose either as you are given by your ISP. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately. Connect on Demand - You can configure the router to disconnect from your Internet connection after a specified period of inactivity (Max Idle Time).
TL-WR841N/TL-WR841ND Figure 4-12 300Mbps Wireless N Router PPTP Settings User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Dynamic IP/ Static IP - Choose either as you are given by your ISP and enter the ISP’s IP address or the domain name. If you choose static IP and enter the domain name, you should also enter the DNS assigned by your ISP. And click the Save button. Click the Connect button to connect immediately.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet connection terminates. Connect Automatically - Connect automatically after the router is disconnected. To use this option, click the radio button. Connect Manually - You can configure the router to make it connect or disconnect manually.
TL-WR841N/TL-WR841ND Figure 4-13 300Mbps Wireless N Router MAC Address Clone Some ISPs require that you register the MAC Address of your adapter. Changes are rarely needed here. WAN MAC Address - This field displays the current MAC address of the WAN port. If your ISP requires you to register the MAC address, please enter the correct MAC address into this field in XX-XX-XX-XX-XX-XX format(X is any hexadecimal digit).
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router MAC Address - The physical address of the router, as seen from the LAN. The value can't be changed. IP Address - Enter the IP address of your router or reset it in dotted-decimal notation (factory default: 192.168.0.1). Subnet Mask - An address code that determines the size of the network. Normally use 255.255.255.0 as the subnet mask. IGMP Proxy - If you want to watch TV through IGMP, please Enable it. Note: 1.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Figure 4-16 Wireless Settings Wireless Network Name - Enter a value of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. Considering your wireless network security, the default SSID is set to be TP-LINK_XXXX (XXXX indicates the last unique four numbers of each router’s MAC address). This value is case-sensitive. For example, TEST is NOT the same as test.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Mode - Select the desired mode. The default setting is 11bgn mixed. 11bg mixed - Select if you are using both 802.11b and 802.11g wireless clients. 11bgn mixed - Select if you are using a mix of 802.11b, 11g, and 11n wireless clients. Select the desired wireless mode. It is strongly recommended that you set the Mode to 802.11b&g&n, and all of 802.11b, 802.11g, and 802.11n wireless stations can connect to the router.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Survey - Click this button, you can search the AP which runs in the current channel. WDS Mode - This field determines which WDS Mode will be used. It is not necessary to change the WDS Mode unless you notice network communication problems with root AP. If you select Auto, then router will choose the appropriate WDS Mode automatically. Key type - This option should be chosen according to the AP's security configuration.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Figure 4-17 Wireless Security Disable Security - If you do not want to use wireless security, select this check box, but it’s strongly recommended to choose one of the following modes to enable security. WPA/WPA2 – Personal (Recommended) - It’s the WPA/WPA2 authentication type based on pre-shared passphrase. • Version - you can choose the version of the WPA-PSK security on the drop-down list.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Figure 4-18 • Wireless Password - You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters. • Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. Be sure to click the Save button to save your settings on this page. WPA /WPA2 – Enterprise - It’s based on Radius Server.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router • Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. WEP - It is based on the IEEE 802.11 standard. If you select this check box, you will find a notice in red as show in Figure 4-20. Figure 4-20 • Type - you can choose the type for the WEP security on the pull-down list.
TL-WR841N/TL-WR841ND 4.6.3 300Mbps Wireless N Router Wireless MAC Filtering Choose menu “Wireless→MAC Filtering”, you can control the wireless access by configuring the Wireless MAC Address Filtering function, shown in Figure 4-21. Figure 4-21 Wireless MAC address Filtering To filter wireless users by MAC Address, click Enable. The default setting is Disabled. MAC Address - The wireless station's MAC address that you want to filter. Status - The status of this entry either Enabled or Disabled.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router To add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example: 00-0A-EB-00-07-8A. 2. Enter a simple description of the wireless station in the Description field. For example: Wireless station A. 3. Status - Select Enabled or Disabled for this entry on the Status pull-down list.
TL-WR841N/TL-WR841ND 4.6.4 300Mbps Wireless N Router Wireless Advanced Choose menu “Wireless→Wireless Advanced”, you can configure the advanced settings of your wireless network. Figure 4-23 Wireless Advanced Transmit Power - Here you can specify the transmit power of router. You can select High, Middle or Low which you would like. High is the default setting and is recommended. Beacon Interval - Enter a value between 20-1000 milliseconds for Beacon Interval here.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Fragmentation Threshold - This value is the maximum size determining whether packets will be fragmented. Setting the Fragmentation Threshold too low may result in poor network performance since excessive packets. 2346 is the default setting and is recommended. DTIM Interval - This value determines the interval of the Delivery Traffic Indication Message (DTIM).
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Current Status - The connected wireless station's running status, one of STA-AUTH / STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN / Disconnected Received Packets - Packets received by the station Sent Packets - Packets sent by the station You cannot change any of the values on this page. To update this page and to show the current connected wireless stations, click on the Refresh button.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Figure 4-26 Guest Network Wireless Settings Allow Guest To Access My Local Network - If enabled, guests can communicate with hosts. Enable Guest Network Bandwidth Control - If enabled, the Guest Network Bandwidth Control rules will take effect. Egress Bandwidth For Guest Network - The upload speed through the WAN port for Guest Network. Ingress Bandwidth For Guest Network - The download speed through the WAN port for Guest Network.
TL-WR841N/TL-WR841ND 4.8 300Mbps Wireless N Router DHCP Figure 4-27 The DHCP menu There are three submenus under the DHCP menu (shown in Figure 4-27): DHCP Settings, DHCP Clients List and Address Reservation. Click any of them, and you will be able to configure the corresponding function. 4.8.1 DHCP Settings Choose menu “DHCP→DHCP Settings”, you can configure the DHCP Server on the page (shown in Figure 4-28).
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes. Default Gateway - (Optional.) Suggest to input the IP address of the LAN port of the router, default value is 192.168.0.1 Default Domain - (Optional.) Input the domain name of your network. Primary DNS - (Optional.) Input the DNS IP address provided by your ISP. Or consult your ISP.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router DHCP server. Reserved IP addresses should be assigned to the servers that require permanent IP settings. Figure 4-30 Address Reservation MAC Address - The MAC address of the PC for which you want to reserve IP address. Assigned IP Address - The IP address of the router reserved. Status - The status of this entry either Enabled or Disabled. To Reserve IP addresses: 1. Click the Add New … button. (Pop-up Figure 4-31) 2.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Click the Enable/ Disabled All button to make all entries enabled/disabled Click the Delete All button to delete all entries Click the Next button to go to the next page and Click the Previous button to return the previous page. 4.9 Forwarding Figure 4-32 The Forwarding menu There are four submenus under the Forwarding menu (shown in Figure 4-32): Virtual Servers, Port Triggering, DMZ and UPnP.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Internal Port - The Internal Service Port number of the PC running the service application. You can leave it blank if the Internal Port is the same as the Service Port, or enter a specific port number when Service Port is a single one. IP Address - The IP Address of the PC providing the service application. Protocol - The protocol used for this application, either TCP, UDP, or All (all protocols supported by the router).
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Click the Enable/ Disabled All button to make all entries enabled/ disabled. Click the Delete All button to delete all entries. Click the Next button to go to the next page and click the Previous button to return the previous page. Note: If you set the service port of the virtual server as 80, you must set the Web management port on System Tools –> Remote Management page to be any other value except 80 such as 8080.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Incoming Port - The port or port range used by the remote system when it responds to the outgoing request. A response using one of these ports will be forwarded to the PC that triggered this rule. You can input at most 5 groups of ports (or port section). Every group of ports must be set apart with ",". For example, 2000-2038, 2050-2051, 2085, 3010-3030.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Click the Enable All button to make all entries enabled Click the Disabled All button to make all entries disabled. Click the Delete All button to delete all entries Note: 1. When the trigger connection is released, the according opening ports will be closed. 2. Each rule allowed to be used only by one host on LAN synchronously. The trigger connection of other hosts on LAN will be refused. 3. Incoming Port Range cannot overlap each other. 4.9.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Internet computers, to access the local host resources or devices as needed. UPnP devices can be automatically discovered by the UPnP service application on the LAN. Figure 4-38 UPnP Setting Current UPnP Status - UPnP can be enabled or disabled by clicking the Enable or Disable button. As allowing this may present a risk to security, this feature is enabled by default. Current UPnP Settings List - This table displays the current UPnP information.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router 4.10 Security Figure 4-39 The Security menu There are four submenus under the Security menu as shown in Figure 4-39: Basic Security, Advanced Security, Local Management and Remote Management. Click any of them, and you will be able to configure the corresponding function. 4.10.1 Basic Security Choose menu “Security → Basic Security”, you can configure the basic security in the screen as shown in Figure 4-37.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router traffic passing through the session conforms to the protocol. SPI Firewall is enabled by factory default. If you want all the computers on the LAN exposed to the outside world, you can disable it. VPN - VPN Passthrough must be enabled if you want to allow VPN tunnels using IPSec, PPTP, or L2TP protocols to pass through the router’s firewall.
TL-WR841N/TL-WR841ND Figure 4-41 300Mbps Wireless N Router Advanced Security Packets Statistics Interval (5~60) - The default value is 10. Select a value between 5 and 60 seconds from the drop-down list. The Packets Statistics Interval value indicates the time section of the packets statistics. The result of the statistics is used for analysis by SYN Flood, UDP Flood and ICMP-Flood. DoS Protection - Denial of Service protection.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router UDP-FLOOD Packets Threshold (5~3600) - The default value is 500. Enter a value between 5 ~ 3600. When the current UPD-FLOOD Packets number is beyond the set value, the router will startup the blocking function immediately. Enable TCP-SYN-FLOOD Attack Filtering - Enable or Disable the TCP-SYN-FLOOD Attack Filtering. TCP-SYN-FLOOD Packets Threshold (5~3600) - The default value is 50. Enter a value between 5 ~ 3600.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router the Setup page of the router's Web-Based Utility locally from inside the network, check the radio button “Only the PCs listed can browse the built-in web pages to perform Administrator tasks”, and then enter each MAC Address in a separate field. The format for the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit).
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router number. For example, if your router's WAN address is 202.96.12.8, and the port number used is 8080, please enter http://202.96.12.8:8080 in your browser. Later, you may be asked for the router's password. After successfully entering the username and password, you will be able to access the router's web-based utility. 2. Be sure to change the router's default password to a very secure password. 4.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router 1. Click the Add New… button and the next screen will pop-up as shown in Figure 4-45. 2. Enter the MAC address of the PC (e.g. 00-11-22-33-44-AA) you’d like to control in the MAC Address of Child PC field. Or you can choose the MAC address from the All Address in Current LAN drop-down list. 3. Give a description (e.g. Allow TP-LINK) for the website allowed to be accessed in the Website Description field. 4.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router For example: If you desire that the child PC with MAC address 00-11-22-33-44-AA can access www.tp-link.com on Saturday only while the parent PC with MAC address 00-11-22-33-44-BB is without any restriction, you should follow the settings below. 1. Click “Parental Control” menu on the left to enter the Parental Control Settings page. Check Enable and enter the MAC address 00-11-22-33-44-BB in the MAC Address of Parental PC field. 2.
TL-WR841N/TL-WR841ND 4.12.1 300Mbps Wireless N Router Rule Choose menu “Access Control → Rule”, you can view and set Access Control rules in the screen as shown in Figure 4-48. Figure 4-48 Access Control Rule Management Enable Internet Access Control - Select the check box to enable the Internet Access Control function, so the Default Filter Policy can take effect. Rule Name - Here displays the name of the rule and this name is unique.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router 4. Select a target from the Target drop-sown list or choose “Click Here To Add New Target List”. 5. Select a schedule from the Schedule drop-down list or choose “Click Here To Add New Schedule”. 6. In the Action field, select Deny or Allow. 7. In the Status field, select Enabled or Disabled to enable or disable your entry. 8. Click the Save button. Click the Enable All button to enable all the rules in the list.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router 5. Click Add New... button to add a new rule as follows: In Rule Name field, create a name for the rule. Note that this name should be unique, for example Rule_1. In Host field, select Host_1. In Target field, select Target_1. In Schedule field, select Schedule_1. In Action field, select Allow. In Status field, select Enable. Click Save to complete the settings.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router 1) In Host Description field, create a unique description for the host (e.g. Host_1). 2) In MAC Address field, enter the MAC address. 3. Click the Save button to complete the settings. Click the Delete All button to delete all the entries in the table. Click the Next button to go to the next page, or click the Previous button return to the previous page.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router 4.12.3 Target Choose menu “Access Control → Target”, you can view and set a Target list in the screen as shown in Figure 4-53. The target list is necessary for the Access Control Rule. Figure 4-53 Target Settings Target Description - Here displays the description about the target and this description is unique. Information - The target can be IP address, port, or domain name. Modify - To modify or delete an existing entry.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Click the Next button to go to the next page, or click the Previous button return to the previous page. Figure 4-54 Add or Modify an Access Target Entry Figure 4-55 Add or Modify an Access Target Entry For example: If you desire to restrict the internet activities of host with MAC address 00-11-22-33-44-AA in the LAN to access www.tp-link.com only, you should first follow the settings below: 1.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router 4.12.4 Schedule Choose menu “Access Control → Schedule”, you can view and set a Schedule list in the next screen as shown in Figure 4-56. The Schedule list is necessary for the Access Control Rule. Figure 4-56 Schedule Settings Schedule Description - Here displays the description of the schedule and this description is unique. Day - Here displays the day(s) in a week. Time - Here displays the time period in a day.
TL-WR841N/TL-WR841ND Figure 4-57 300Mbps Wireless N Router Advanced Schedule Settings For example: If you desire to restrict the internet activities of host with MAC address 00-11-22-33-44-AA to access www.tp-link.com only from 18:00 to 20:00 on Saturday and Sunday, you should first follow the settings below: 1. Click Add New... button shown in Figure 4-56 to enter the Advanced Schedule Settings page. 2. In Schedule Description field, create a unique description for the schedule (e.g. Schedule_1). 3.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router 4.13.1 Static Routing List Choose menu “Advanced Routing → Static Routing List”, and then you can configure the static route in the next screen (shown in Figure 4-59). A static route is a pre-determined path that network information must travel to reach a specific host or network. Figure 4-59 Static Routing To add static routing entries: 1. Click Add New… shown in Figure 4-59, you will see the following screen. Figure 4-60 2.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Other configurations for the entries: Click the Delete button to delete the entry. Click the Enable All button to enable all the entries. Click the Disable All button to disable all the entries. Click the Delete All button to delete all the entries. Click the Previous button to view the information in the previous screen, click the Next button to view the information in the next screen. 4.13.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router 4.14 Bandwidth Control Figure 4-62 There are two submenus under the Bandwidth Control menu as shown in Figure 4-62. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.14.1 Control Settings Choose menu “Bandwidth Control → Control Settings”, you can configure the Egress Bandwidth and Ingress Bandwidth in the next screen.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Figure 4-64 Bandwidth Control Rules List Description - This is the information about the rules such as address range. Egress bandwidth - This field displays the max and mix upload bandwidth through the WAN port, the default is 0. Ingress bandwidth - This field displays the max and mix download bandwidth through the WAN port, the default is 0. Enable - This displays the status of the rule. Modify - Click Modify to edit the rule.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router There are two submenus under the IP &MAC Binding menu (shown in Figure 4-66): Binding Settings and ARP List. Click any of them, and you will be able to scan or configure the corresponding function. The detailed explanations for each submenu are provided below. 4.15.1 Binding Settings This page displays the IP & MAC Binding table; you can operate it in accord with your desire. (shown in Figure 4-67).
TL-WR841N/TL-WR841ND 3. Select the Bind checkbox. 4. Click the Save button to save it. 300Mbps Wireless N Router To modify or delete an existing entry, follow the steps below. 1. Find the desired entry in the table. 2. Click Modify or Delete as desired on the Modify column. To find an existing entry, follow the steps below. 1. Click the Find button as shown in Figure 4-67. 2. Enter the MAC Address or IP Address. 3. Click the Find button in the page as shown in Figure 4-69.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router IP Address - The assigned IP address of the controlled computer in the LAN. Status - Indicates whether or not the MAC and IP addresses are bound. Configure - Load or delete an item. Load - Load the item to the IP & MAC Binding list. Delete - Delete the item. Click the Bind All button to bind all the current items, available after enable. Click the Load All button to load all items to the IP & MAC Binding list.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Figure 4-71 Comexe.cn DDNS Settings To set up for DDNS, follow these instructions: 1. Type the Domain Name received from your dynamic DNS service provider. 2. Type the User Name for your DDNS account. 3. Type the Password for your DDNS account. 4. Click the Login button to log in to the DDNS service. Connection Status -The status of the DDNS service connection is displayed here. Click Logout to log out of the DDNS service. 4.16.2 Dyndns.
TL-WR841N/TL-WR841ND Figure 4-72 300Mbps Wireless N Router Dyndns.org DDNS Settings To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3. Type the Domain Name you received from dynamic DNS service provider here. 4. Click the Login button to log in to the DDNS service. Connection Status -The status of the DDNS service connection is displayed here. Click Logout to logout of the DDNS service. 4.16.3 No-ip.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Figure 4-73 No-ip.com DDNS Settings To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3. Type the Domain Name you received from dynamic DNS service provider. 4. Click the Login button to log in the DDNS service. Connection Status - The status of the DDNS service connection is displayed here. Click Logout to log out the DDNS service. 4.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router 4.17.1 IPv6 Status Figure 4-75 IPv6 Status The IPv6 Status page displays the router's current IPv6 status and configuration. All information is read-only. WAN • Connection Type - The IPv6 connection way for WAN. • IPv6 Address - The WAN IPv6 address. • IPv6 Default Gateway - The router's default gateway. • Primary IPv6 DNS - The primary IPv6 DNS address. • Secondary IPv6 DNS - The secondary IPv6 DNS address.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router 4.17.2 IPv6 Setup Figure 4-76 Enable/Disable IPv6 Enable IPv6 - Tick the checkbox to enable the IPv6 function. It’s enabled by default. WAN Connection Type - Choose the correct WAN connection type based on your ISP network topology. • SLAAC - Connections which use RADVD IPv6 address assignment. • DHCPv6 - Connections which use dynamic IPv6 address assignment. • Static IPv6 - Connections which use static IPv6 address assignment.
TL-WR841N/TL-WR841ND 1) 300Mbps Wireless N Router SLAAC Figure 4-77 SLAAC IPv6 Address - The IPv6 address assigned by your ISP dynamically. IPv6 Address Prefix - Display the IPv6 Prefix Length in dotted-decimal notation provided by your ISP. Default Gateway - Display the default gateway in colon-hexadecimal notation provided by your ISP. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Address Autoconfiguration Type - RADVD (Router Advertisement Daemon) and DHCPv6 (Dynamic Host Configuration Protocol for IPv6) Server. Site Prefix Configuration Type - The type of IPv6 address prefix. • Delegated - Get the IPv6 address prefix from the ISP automatically, and the device will delegate it to the LAN. • Static - Configure the Site Prefix and Site Prefix Length manually.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Primary IPv6 DNS - Enter the DNS IPv6 address in dotted-decimal notation provided by your ISP. Secondary IPv6 DNS - Enter another DNS IPv6 address in dotted-decimal notation provided by your ISP. Note: If you get Address not found error when you access a Web site, it is likely that your DNS servers are set up improperly. You should contact your ISP to get DNS server addresses.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router IPv6 Address - Enter the IPv6 address in dotted-decimal notation provided by your ISP. Default Gateway - Enter the default gateway in dotted-decimal notation provided by your ISP. MTU Size (in bytes) - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. For some ISPs, you may need to modify the MTU. But this is rarely required, and should not be done unless you are sure it is necessary for your ISP connection.
TL-WR841N/TL-WR841ND 4) 300Mbps Wireless N Router PPPoEv6 Figure 4-80 PPPoEv6 PPPoE Session - The PPP session type for IPv6 connection. There are two types: • Share with PPPoEv4 - The PPPoEv6 and PPPoEv4 use the same PPP session. • Create a new Session - The PPPoEv6 and PPPoEv4 use different PPP sessions. It is default to select this option. User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Connection Mode - The way to connect the ISP. • Alway On - Connect automatically. • Connect Manual - Connect by the user manually. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately. Address Autoconfiguration Type - RADVD (Router Advertisement Daemon) and DHCPv6 (Dynamic Host Configuration Protocol for IPv6) Server. Site Prefix Configuration Type - The type of IPv6 address prefix.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Tunnel Address - The 6to4 tunnel address created by the device to access to the IPv6 network. MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1480 Bytes. For some ISPs, you may need to modify the MTU. But this is rarely required, and should not be done unless you are sure it is necessary for your ISP connection.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Choose menu “System Tools”, and you can see the submenus under the main menu: Time Settings, Diagnostic, Firmware Upgrade, Factory Defaults, Backup & Restore, Reboot, Password, System Log and Statistics. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.18.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router To set time manually: 1. Select your local time zone. 2. Enter the Date in Month/Day/Year format. 3. Enter the Time in Hour/Minute/Second format. 4. Click Save. To set time automatically: 1. Select your local time zone. 2. Enter the address or domain of the NTP Server I or NTP Server II. 3. Click the Get GMT button to get system time from Internet if you have connected to the Internet. To set Daylight Saving: 1.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Figure 4-84 Diagnostic Tools Diagnostic Tool - Check the radio button to select one diagnostic too. Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. Traceroute - This diagnostic tool tests the performance of a connection. Note: You can use ping/traceroute to test both numeric IP address or domain name.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Click Start to check the connectivity of the Internet. The Diagnostic Results page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of the Internet is fine. Figure 4-85 Diagnostic Results Note: Only one user can use this tool at one time. Options “Number of Pings”, “Ping Size” and “Ping Timeout” are used for Ping function. Option “Tracert Hops” are used for Tracert function. 4.18.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router 3. Click the Upgrade button. Note: 1. New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the router rather than the configuration, you can try to upgrade the firmware. 2.
TL-WR841N/TL-WR841ND Figure 4-88 300Mbps Wireless N Router Backup & Restore Configuration Click the Backup button to save all configuration settings as a backup file in your local computer. To upgrade the router's configuration, follow these instructions. • Click the Browse… button to locate the update file for the router, or enter the exact path to the Setting file in the text box. • Click the Restore button.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router 4.18.7 Password Choose menu “System Tools → Password”, you can change the factory default user name and password of the router in the next screen as shown in Figure 4-77. Figure 4-90 Password It is strongly recommended that you should change the factory default user name and password of the router, because all users who try to access the router's Web-based utility or Quick Setup will be prompted for the router's default user name and password.
TL-WR841N/TL-WR841ND Figure 4-91 300Mbps Wireless N Router System Log Auto Mail Feature - Indicates whether auto mail feature is enabled or not. Mail Settings - Set the receiving and sending mailbox address, server address, validation information as well as the timetable for Auto Mail Feature, as shown in Figure 4-92. Figure 4-92 Mail Account Settings From - Your mail box address. The router would connect it to send logs. To - Recipient’s address.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Authentication - Most SMTP Server requires Authentication. It is required by most mailboxes that need User Name and Password to log in. Note: Only when you select Authentication, do you have to enter the User Name and Password in the following fields. User Name - Your mail account name filled in the From field. The part behind @ is included. Password - Your mail account password. Confirm The Password - Enter the password again to confirm.
TL-WR841N/TL-WR841ND Figure 4-93 300Mbps Wireless N Router Statistics Current Statistics Status - Enable or Disable. The default value is disabled. To enable, click the Enable button. If disabled, the function of DoS protection in Security settings will be disabled. Packets Statistics Interval （5-60） - The default value is 10. Select a value between 5 and 60 seconds in the pull-down list. The Packets Statistic interval indicates the time section of the packets statistic.
TL-WR841N/TL-WR841ND Modify 300Mbps Wireless N Router UDP Tx The number of UDP packets transmitted to the WAN per second at the specified Packets Statistics interval. It is shown like “current transmitting rate / Max transmitting rate”. TCP SYN Tx The number of TCP SYN packets transmitted to the WAN per second at the specified Packets Statistics interval. It is shown like “current transmitting rate / Max transmitting rate”. Reset Reset the value of he entry to zero.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Appendix A: FAQ 1. How do I configure the router to access Internet by ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your ADSL Modem to the WAN port on the router. The telephone cord plugs into the Line port of the ADSL Modem. 3) Login to the router, click the “Network” menu on the left of your browser, and click "WAN" submenu.
TL-WR841N/TL-WR841ND 2. 300Mbps Wireless N Router How do I configure the router to access Internet by Ethernet users? 1) Login to the router, click the “Network” menu on the left of your browser, and click "WAN" submenu. On the WAN page, select “Dynamic IP” for "WAN Connection Type", finish by clicking “Save”. 2) Some ISPs require that you register the MAC Address of your adapter, which is connected to your cable/DSL Modem during installation.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Figure A-5 Add or Modify a Virtual server Entry Note: Your opposite side should call your WAN IP, which is displayed on the “Status” page. 4) How to enable DMZ Host: Log in to the router, click the “Forwarding” menu on the left of your browser, and click "DMZ" submenu. On the "DMZ" page, click Enable radio button and type your IP address into the “DMZ Host IP Address” field, using 192.168.0.198 as an example, remember to click the Save button.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Figure A-7 Basic Security 4. I want to build a WEB Server on the LAN, what should I do? 1) Because the WEB Server port 80 will interfere with the WEB management port 80 on the router, you must change the WEB management port number to avoid interference. 2) To change the WEB management port number: Log in to the router, click the “Security” menu on the left of your browser, and click "Remote Management" submenu.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Note: If the above configuration takes effect, to configure to the router by typing http://192.168.0.1:88 (the router’s LAN IP address: Web Management Port) in the address field of the Web browser. 3) Log in to the router, click the “Forwarding” menu on the left of your browser, and click the "Virtual Servers" submenu.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Appendix B: Configuring the PC In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows 7. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if needed. 1. Install TCP/IP component 1) On the Windows taskbar, click the Start button, and then click Control Panel. 2) Click the Network and Internet, and click the Network and Sharing Center, then click Change adapter settings.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Figure B-0-2 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Figure B-0-3 Setting IP address manually 1 Select Use the following IP address radio button. And the following items available 2 If the router's LAN IP address is 192.168.0.1, specify the IP address as 192.168.0.x (x is from 2 to 254), and Subnet mask is 255.255.255.0. 3 Type the router’s LAN IP address (the default IP is 192.168.0.1) into the Default gateway field. 4 Select Use the following DNS server addresses radio button.
TL-WR841N/TL-WR841ND Figure B-0-4 -110- 300Mbps Wireless N Router
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Appendix C: Specifications General Standards IEEE 802.3, 802.3u, 802.11b, 802.11g and 802.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router Appendix D: Glossary 802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding schemes like Alamouti coding. The Enhanced Wireless Consortium (EWC) [3] was formed to help accelerate the IEEE 802.
TL-WR841N/TL-WR841ND 300Mbps Wireless N Router SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name.
