Network Cables - Network Adapter User Manual

ManualsBrandsTransition Networks ManualsNetwork RouterSWITCHABLE ETHERNET AND FAST ETHERNET SSEFE10XX-10X

* Typical maximum cable distance. Actual distance is dependent upon the

physical characteristics of the network. (TX) = transmit, (RX) = receive

The SSEFE10xx-10x media converter is designed to be installed in pairs, where one

is the local media converter and the other is the remote. For example, a local

SSEFE1011-100 converter is connected, via fiber, to a remote SSEFE1011-100

converter.

For a single fiber network, a local SSEFE1029-100 is connected, via fiber, to a

remote SSEFE1029-101 converter.

Installation . . . . . . . . . . . . . . . . . .2

Operation . . . . . . . . . . . . . . . . . . .5

Cable Specifications . . . . . . . . . . .6

Technical Specifications . . . . . . . .8

Troubleshooting . . . . . . . . . . . . . .9

Compliance Information . . . . . . .12

User’s Guide

SSEFE10xx-10x

Stand-Alone Media Converter

• Switchable Ethernet and Fast Ethernet

• 10 Mb/s Copper to Fiber

• 100 Mb/s Copper to Fiber

Transition Networks SSEFE10xx-10x series

Ethernet / Fast Ethernet media converter is a

10Mbps or 100Mbps switch-selectable media

converter. Both the copper and fiber links operate at the same speed setting via a

hard set with a dip switch, so the media converter operates at either 10 Mb/s

copper to fiber or 100 Mb/s copper to fiber.

Part Number Port One - Twisted-Pair

Copper

Port Two - Fiber Optic

SSEFE1012-100 RJ-45, 100 m (328 ft)* ST, 1310 nm single mode

duplex fiber, 20 km (12.4 miles)*

SSEFE1014-100 RJ-45, 100 m (328 ft)* SC, 1310 nm single mode

duplex fiber, 20 km (12.4 miles)*

SSEFE1015-100 RJ-45, 100 m (328 ft)* SC, 1310 nm single mode

duplex fiber, 40 km (24.8 miles)*

SSEFE1022-100 RJ-45, 100 m (328 ft)* ST, 1310 nm single mode

duplex fiber, 40 km (24.8 miles)*

SSEFE1029-100 RJ-45, 100 m (328 ft)* SC, 1310 mn (TX)/1550 nm (RX)

single fiber, 20 km (12.4 miles)*

SSEFE1029-101 RJ-45, 100 m (328 ft)* SC, 1550 mn (TX)/1310 nm (RX)

single fiber, 20 km (12.4 miles)*

Summary of content (7 pages)

PAGE 1
User’s Guide SSEFE10xx-10x Stand-Alone Media Converter • Switchable Ethernet and Fast Ethernet • 10 Mb/s Copper to Fiber • 100 Mb/s Copper to Fiber Transition Networks SSEFE10xx-10x series Ethernet / Fast Ethernet media converter is a 10Mbps or 100Mbps switch-selectable media converter. Both the copper and fiber links operate at the same speed setting via a hard set with a dip switch, so the media converter operates at either 10 Mb/s copper to fiber or 100 Mb/s copper to fiber.
PAGE 2
SSEFE10xx-10x Installation Installation -- Continued The Link Pass-Through and speed switches are located on the side of the media converter. Use a small screwdriver to set the recessed switches. Link Pass-Through: up = Enable Speed: up = 100 Mb/s Set Link Pass-Through (switch 1) Switch 1 sets the Link Pass-Through feature: up = Enable Link Pass-Through. down = Disable Link Pass-Through.
PAGE 3
SSEFE10xx-10x Installation -- Continued Operation Install the Fiber Cable Status LEDs The SSEFE10xx-10x is designed to be installed in pairs over the fiber link, where one is the local media converter and the other is the remote. Use the status LEDs to monitor the SSEFE10xx-10x media converter operation in the network. 1. Locate or build fiber-optic cable with male, two-stranded TX to RX connectors installed at both ends. PWR Power On = Connection to the external AC or DC power. 2.
PAGE 4
SSEFE10xx-10x Cable Specifications Cable Specifications -- Continued The physical characteristics must meet or exceed IEEE 802.3™ specifications. Fiber Cable Bit Error Rate: Single mode: <10-9 9 µm SSEFE1012-100 Fiber-optic Transmitter Power: Fiber-optic Receiver Sensitivity: Link Budget: 1310 nm single mode min: -15.0 dBm max: -8.0 dBm min: -32.0 dBm max: -5.0 dBm 17.0 dB SSEFE1014-100 Fiber-optic Transmitter Power: Fiber-optic Receiver Sensitivity: Link Budget: 1310 nm single mode min: -15.
PAGE 5
SSEFE10xx-10x Technical Specifications For use with Transition Networks Model SSEFE10xx-10x or equivalent. Standards: IEEE 802.3™, 10Base-T, 100Base-TX, 100Base-FX Data Rate: 10 Mb/s, 100 Mb/s Dimensions 3.25" x 4.7" x 1.0" (83 mm x 119 mm x 25 mm) Weight 10 oz. ( 283 g) (approximate) Power Consumption: 3.6 watts Power Supply 12VDC, 0.5 Amp (North America) 12VDC, 0.41 Amp (Europe, Japan, Latin Am.) 12VDC, 1.
PAGE 6
SSEFE10xx-10x Troubleshooting -- Continued 6. 7. Is the TP-ACT LED illuminated? NO • Check the twisted-pair copper cables for proper connection. • Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600. YES • Go to step 7. Is the TP-ACT LED blinking? NO • If there is activity on the copper port, disconnect and reconnect the copper cable to restart the initialization process. • Restart the workstation to restart the initialization process.
PAGE 7
Compliance Information CISPR22/EN55022 Class A + EN55024 CE Mark FCC Regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.