Network Cables - Network Adapter User Manual

8
SSEFE10xx-10x
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Technical Specifications
For use with Transition Networks Model SSEFE10xx-10x or equivalent.
Standards: IEEE 802.3™, 10Base-T, 100Base-TX, 100Base-FX
Data Rate: 10 Mb/s, 100 Mb/s
Dimensions 3.25" x 4.7" x 1.0" (83 mm x 119 mm x 25 mm)
Weight 10 oz. ( 283 g) (approximate)
Power Consumption: 3.6 watts
Power Supply 12VDC, 0.5 Amp (North America)
12VDC, 0.41 Amp (Europe, Japan, Latin Am.)
12VDC, 1.25 Amp (UK, Australia, South Africa)
Environment: Tmra*: 0° to 50°C (32° to 122°F)
Storage Temperature: -20° to 85°C (-4° to 185°F)
Humidity: 5 to 95%, non condensing
Altitude: 0 to 10,000 feet
Warranty: Lifetime
*Manufacturer’s rated ambient temperature:
NOTE: The information in this user’s guide is subject to change. For the most
up-to-date information on the SSEFE10xx-10x media converter, view the user’s
guide on-line at: www.transition.com.
The chassis version of the media converter is the CSEFE10xx-10x model. For
more information, see the CSEFE10xx-10x user’s guide on-line at:
www.transition.com.
Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,
Subchapter J applicable at the date of manufacture.
CAUTION: Visible and invisible laser radiation when open. Do not stare into
beam or view directly with optical instruments.
CAUTION: Use of controls, adjustments or the performance of procedures other
than those specified herein may result in hazardous radiation exposure.
9
[e-mail] -- Click the “Transition Now” link for a live Web chat
Troubleshooting
1. Is the PWR LED on the media converter illuminated?
NO
• Ensure that the power adapter is the proper type of voltage and cycle
frequency for the outlet (See “Power Supply” on page 8.)
• Ensure the power adapter is properly installed in the media converter
and in the grounded outlet.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Go to step 2.
2. Is the F-ACT LED illuminated?
NO
• Check the fiber cables for proper connection.
• Verify that the TX and RX cables on the media converter are
connected to the RX and TX ports, respectively, on the other media
converter.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Go to step 3.
3. Is the F-ACT LED blinking?
NO
• If there is no activity on the fiber port, go to step 4.
• If there is activity on the fiber port, disconnect and reconnect the
fiber cable to restart the initialization process.
• Restart the workstation to restart the initialization process.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Go to step 4.
4. Are the F-100 and/or the TP-100 LEDs illuminated?
YES
• The media converter is set to 100Mb/s for both the copper fiber links.
If this is not the correct speed, carefully remove the media converter
from the chassis and set switch 1 to “down” (speed = 10 Mb/s).
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
NO
• Go to step 5.
5. Are the F-10 and/or the TP-10 LEDs illuminated?
YES
• The media converter is set to 10 Mb/s for the copper and fiber links.
If this is not the correct speed, carefully remove the media converter
from the chassis and set switch 2 to “up” (speed = 100 Mb/s).
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
NO
• Go to step 6.