TEW-450APB Super G Access Point Quick Installation Guide Point d'accès Super G Guide d'installation rapide Super G Access Point Kurzanleitung zur Installation Punto de Acceso Súper G Guía de instalación rápida Точка доступа Super G Руководство по быстрой установке Version 06.28.2005 TRENDnet TRENDware, USA What's Next in Networking Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
Table of Contents English ...................................................................................................... 1. Prepare for Installation ...................................................................... 2. Install Hardware ................................................................................ 3. Configure TCP/IP Settings ................................................................ 4. Configure the Access Point ...........................................................
English QIG 1. Prepare for Installation Thank you for purchasing TRENDnet's TEW-450APB Super G Access Point This guide will help you set-up your Access Point quickly and easily. Just follow the step-by-step instructions below, and enjoy the benefits of accessing the Internet without ever being tied down to wires! If you run into problems, please refer to the Troubleshooting section. If you need further technical support, please visit www.TRENDNET.com or call technical support by phone.
2. Install Hardware 1. Locate an optimum location for the Access Point. The best place for the Access Point is usually at the center of your wireless network. 2. Connect the RJ-45 network cable to the Access Point, then connect the other end of the network cable to a Switch or Hub. The Access Point is now connected to your 10/100Mbps network. 3. Connect the power adapter to the Access Point.
3. Configure TCP/IP Settings Before the Access Point can be accessed and configured, the computer's TCP/IP settings need to be changed. (That includes your wireless card's IP address, too.) Windows 2000/XP 1. Find the Start button located on the Desktop. 2. Click Start, and click on Control Panel. For Windows 2000, click Start, highlight Settings, and click Control Panel. 3. Double-Click the Network Connection icon. 4. Right-Click on the Local Area Connection icon, then click on Properties.
. Click on Use the following IP address. Enter 192.168.1.50 for IP address and 255.255.255.0 for Subnet, then click OK. 7. Click OK. 8. Your computer is now ready to access and configure the Access Point.
4. Configure the Access Point From a Wired Computer 1. Open a web browser (Internet Explorer or Netscape) and enter http://192.168.1.1 at the address bar, then press the Enter key. Type admin for username, and type admin for your password. Click OK. 2. Click Wizard.
3. Click Next. 4. If you want to change the default password, type in a new password and click Next. Otherwise, click Next.
5. If you want to change the default SSID or channel, type in the appropriate information and click Next. Otherwise, click Next. 6. Click Next.
7. Click Restart and click Close. Congratulations! Installation is now complete. From a Wireless Computer (using TRENDnet's TEW-441PC as an example in this section) The default settings of the Access Point are: SSID - AP254f02 Channel - 6 8. On your wireless computer, open up your Wireless Utility Program.
9. Click Site Survey, select AP254f02 or the SSID that you assigned the TEW450APB, and click Connect. If you do not see the TEW-450APB's SSID, click Refresh. 10. Click Apply. 11. Go to the beginning of section 4. Configure the Access Point and follow steps 1-7.
Troubleshooting Q1: I typed http://192.168.1.1 in my Internet browser's address bar, but error message says "The page cannot be displayed". How can I get into the TEW-450APB's web configuration page? A1: Please check your hardware and TCP/IP settings again by following the instructions in sections 1~3. Make sure the Power, LAN, and WLAN LEDs are lit and the TCP/IP configurations are correct. Then try accessing http://192.168.1.1 again.
TRENDnet TRENDware, USA What's Next in Networking @ Product Warranty Registration Please take a moment to register your product online. Go to TRENDware’s website at http://www.TRENDNET.com TRENDnet Technical Support US/Canada Support Center Contact Telephone: 1(310) 626-6252 Fax: 1(310) 626-6267 Email: support@trendnet.