Quick Installation Guide TS-I300 TS-I300W
Table ofofContents Table Contents English ..................................................................................................... 1. Before You Start ................................................................................ 2. Hardware Installation ......................................................................... 3. Configure the Storage Server ............................................................ 4. Accessing Storage Devices on TS-I300/TS-I300W ..........................
1. Before You Start Package Contents TS-I300/TS-I300W User's Guide CD-ROM Quick Installation Guide Mounting Stand AC Power Adapter (12V DC, 3.0A) 1 x 2dBi Detachable Antenna (TS-I300W) System Requirements Web Browser: Internet Explorer (5.5 or higher) A computer with a network adapter properly installed. A network Switch or Hub with an available network LAN port. A RJ-45 network cable. IDE Internal Hard Drive or USB 2.0 Storage Device (i.e.
2. Hardware Installation Note: Before installing the IDE hard drive, the jumper settings must be set to Master. 1. Remove the two screws from the rear panel to detach the cover. 2. Make sure the jumper settings on the hard drive is set to Master. 3. Connect the IDE cable and power cable to the hard drive. 4. Place the hard drive onto the metal bracket and secure it with four mounting screws. 5. Replace the cover and secure the two screws.
6. Attach the mounting stand to the Storage Server. 7. Connect a RJ-45 cable from the Switch/Hub to the LAN port of the Storage Server and then connect the 2dBi Detachable Antenna (TS-I300W). 8. Connect the External Power Adapter to the Storage Server and then to a power outlet. 9. Verify that the following panel lights are on: Power, LAN, HDD and WLAN (TS-I300W). Your hardware installation is now complete.
3. Configure the Storage Server Note: Install and use the Easy Search Utility to discover all the TS-I300/TSI300W on the network, assign IP Address, change the host name and workgroup, and mount or unmount the hard drive. For Windows Users 1. Insert the Utility CD-ROM into your computer's CD-ROM Drive and then click Easy Search Utility. 2. Click on Search device, and then select the Storage Server. 3. Configure the IP (IP address), Network (Subnet mask), Gateway and then click Modify.
Note: If your hard drive has already been formatted, please skip to step 9. If you are attaching a brand new hard drive, please continue on to step 5. 5. Click Format Hard Drive. 6. Click OK. 7. Click Restart. 8. Click OK.
9. Enter the User name and Password, and then click Config. User Name: admin Password: admin Note: For the TS-I300 skip to section 4. For the TS-I300W continue on to step 10. 10. Click Advanced and then Wireless. 11. Click Access Point, and then click Enable. Enter an SSID and then click Apply. Your configuration is now complete.
4. Accessing Storage Devices on TS-I300/TS-I300W 1. Select the hard drive, and then click Mount. 2. Click OK. 3. Double-click on My Computer. Then double-click on any mounted hard drive under Network Drives.
Troubleshooting Q1: Can I connect or disconnect the USB storage device while the TS-I300/TS-I300W is on? A1: Yes, you can connect or disconnect any external USB device while the computer is on, because the USB interfaces are Plug-and-Play and hot-pluggable. Just press on the Unmount button on the unit or open the utility program and press unmount for the USB device. Q2: I specified the IP address http://192.168.1.
Q4: All the settings are correct, but I can not make a wireless connection to the TS-I300W. A4: First, double check that the WLAN light on the storage device is lit. Second, power cycle the Access Point. Unplug the power to the TS-I300W. Wait 15 seconds, then plug the power back in. Third, contact the manufacturer of your wireless network adapter. Make sure the wireless network adapter is configured with the proper SSID. The default SSID of the Access Point is TRENDnet.
TRENDnet Technical Support US . Canada Toll Free Telephone: 1(866) 845-3673 24/7 Tech Support Europe (Germany . France . Italy . Spain . Switzerland . UK) Toll Free Telephone: +00800 60 76 76 67 English/Espanol - 24/7 Francais/Deutsch - 11am-8pm, Monday - Friday MET Worldwide Telephone: +(31) (0) 20 504 05 35 English/Espanol - 24/7 Francais/Deutsch - 11am-8pm, Monday - Friday MET Product Warranty Registration Please take a moment to register your product online. Go to TRENDnet’s website at http://www.
