12U Wall-Mounted SmartRack Enclosure Owner's Manual

ManualsBrandsTripp Lite ManualsNetwork Router12U Wall-Mounted SmartRack Enclosure SRW12US

Table of Contents

1. Important Safety Instructions 2

2. Overview 2

3. Feature Identiﬁcation 3

4. Enclosure Installation 4

4.1 Preparation 4

4.2 Unpacking 4

4.3 Placement 4

4.4 Ground Connection 5

5. Enclosure Conﬁguration 5

5.1 Door Locks 5

5.2 Cable Access & Management 5

5.3 Reversing the Enclosure 5

5.4 Mounting Rails 6

5.5 Adjusting Mounting Rail Depth 6

6. Wall Mounting the Enclosure 6

6.1 Mounting 6

7. Equipment Installation 7

7.1 Installing or Removing Cage Nuts 7

8. Optional Casters 7

9. Speciﬁcations 8

10. Storage and Service 8

11. Warranty & Warranty Registration 8

Francais 9

12U Wall-Mounted

SmartRack

™

Enclosure

Model: SRW12US

Owner’s Manual

WARRANTY

REGISTRATION

to win a FREE Tripp Lite product

www.tripplite.com/warranty

Tripp Lite World Headquarters

1111 W. 35th Street, Chicago, IL 60609 USA

(773) 869-1234 • www.tripplite.com

Summary of content (8 pages)

PAGE 1
e nc Y N a ct NT IO a ch rodu A R AT for te p anty R A TR ay Li rr W IS e tod ripp /wa G in T om RE nl E .c E ite o er FR pl st a trip i g in . Re o w ww t w Owner’s Manual 12U Wall-Mounted SmartRack™ Enclosure Model: SRW12US Table of Contents 1. Important Safety Instructions 2 6. Wall Mounting the Enclosure 6 2. Overview 2 6.1 Mounting 6 3. Feature Identification 3 7. Equipment Installation 7 4. Enclosure Installation 4 7.1 Installing or Removing Cage Nuts 7 4.1 Preparation 4 8.
PAGE 2
1. Important Safety Instructions SAVE THESE INSTRUCTIONS This Manual contains instructions and warnings that must be followed during the installation and operation of the product described in this manual. Failure to comply may invalidate the warranty and cause property damage or personal injury. • Keep the enclosure in a controlled indoor environment, away from moisture, temperature extremes, flammable liquids and gasses, conductive contaminants, dust and direct sunlight.
PAGE 3
. Feature Identification 5 5 6 7 3 1 4 3 4 2 5 3 7 1 2 3 4 5 6 7 Rear Door Front Door Horizontal Rails Vertical Mounting Rails Removeable Cable Access Hole Covers Vents Locking/Removeable Side Panels 6 3
PAGE 4
. Enclosure Installation Caution! Read All Instructions and Warnings Before Installation! Warning: Rack enclosures can be extremely heavy. Do not attempt to unpack, move or install the enclosure without assistance. Use extreme caution when handling the enclosure and be sure to follow all handling and installation instructions. Do not attempt to install equipment without first stabilizing the enclosure. 4.
PAGE 5
4. Enclosure Installation (continued) 4.4 Ground Connection All parts of the enclosure are grounded to the frame of the enclosure. Use the enclosure’s front or rear threaded grounding point A and an M6 screw (included) to connect the frame of the enclosure directly to your facility’s earth ground connection with an 8 AWG (3.264 mm) wire. Route the ground wire under the enclosure’s frame to ensure unhindered door operation. Warning: Attach each enclosure to earth ground separately.
PAGE 6
5. Enclosure Configuration (continued) 5.4 Mounting Rails The enclosure comes with mounting rails that have square holes for mounting rack equipment. To install equipment, use the included cage nuts and other hardware. (See page 7 for installation of cage nuts.) Warning: Be sure to have the enclosure securely mounted to the wall, or in its final position on the floor before mounting any equipment inside. Also be sure to have all the right adjustments on your rails before mounting equipment.
PAGE 7
29 7. Equipment Installation 28 28 27 27 Warning: Do not install equipment until you have stabilized the enclosure. Install heavier equipment first and install it towards the bottom of the enclosure. Install equipment starting from the bottom of the enclosure and proceeding toward the top of the enclosure - never the reverse. If using sliding equipment rails, be careful when extending the rails. Do not extend more than one set of sliding equipment rails at one time.
PAGE 8
9. Specifications Model SRW12US Dimensions (H x W x D) 25 x 23.63 x 21.6” (635 x 600 x 549 mm) Unit Weight 60 lb (27 kg) Load Capacity* 200 lb (90 kg) Stationary/ 200 lb (90 kg) Rolling Mounting Depth Adjustable from 3” to 20.5” (76 to 521 mm) * Full wall-mount load capacity requires a mounting surface capable of bearing the full load. Rolling applications require optional SRCASTER accessory kit. 10.