Installation Guide

ManualsBrandsTroposAir ManualsCeiling FansLiberator 72 w/610 72-in Gloss White LED Indoor/Outdoor Downrod Ceiling Fan with Remote (9-Blade)

(9TB 72"/82")

Liberator

6.2 KGS.

13.6 LBS.

Net weight

Toll Free: 1-855-676-7247

This instruction contains 9 pages:

Page 1: Read Safety instructions

Page 2: Unpack and inspect parts contained

Page 3~4: Notes before installation and Hanging system installation

/Blade installation

Page 5: Wire connection

Page 6: Canopy installation / Remote Transmitter assembly

Page 7: Operational instruction / Troubleshooting

Page 8~9: Remote Pairing Process

WARNING : Read and follow these instructions carefully and be mindful of all warnings shown throughout.

Summary of content (10 pages)

PAGE 1
Liberator (9TB 72"/82") This instruction contains 9 pages: Page 1: Read Safety instructions Page 2: Unpack and inspect parts contained Page 3~4: Notes before installation and Hanging system installation /Blade installation Page 5: Wire connection Page 6: Canopy installation / Remote Transmitter assembly Page 7: Operational instruction / Troubleshooting Page 8~9: Remote Pairing Process Net weight 6.2 KGS. 13.6 LBS.
PAGE 2
P1 READ AND SAVE THESE INSTRUCTIONS WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, PLEASE OBSERVE THE FOLLOWING : 1]. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning. 2]. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring. All electrical connections must be made in accordance with local codes, ordinances and/or the National Electric Code.
PAGE 3
P2 Unpack and inspect fan carefully to ensure all contents are included. Unpack (Fan & Blades packed Separately) Note: Make sure you have received two boxes, one for fan and one for blades.
PAGE 4
P3 WARNING: BLADES SHOULD BE AT LEAST 7 FEET FROM FLOOR Note 1: Note 2: Turn off power at breaker box to avoid possible electrical shock. Use metal outlet box suitable for fan support. Outlet box must support 35 lbs min. OFF OFF OFF 1. HANGING SYSTEM INSTALLATION Installing mounting bracket to ceiling outlet box 1-1. Outlet Box Mounting Bracket 1-2. Screw (2) Spring Washer Flat Washer (Loosening) 1-1.
PAGE 5
P4 Lead Wires Canopy Cross Pin Yoke Cover Yoke cover Downrod Assembly Cotter Pin Yoke Downrod Jam Screws (2) (Tightening) Fan Assembly Fan Assembly 2-4. Insert the lead wires through the downrod assembly. 2-5. Insert downrod assembly into yoke and attach the cross pin through yoke & downrod, secure with cotter pin. 2-6. Tighten both downrod jam screws to secure downrod. 2-7. Pull down the yoke cover to cover yoke. 3.
PAGE 6
P5 5. WIRE CONNECTION 5-1. Verify that serial Number & Model Number match on the Receiver and Transmitter NOTICE: Many remote sets for DC fans look the same. This remote set is pre-paired and labeled at the factory, please note the following before operation: 1a. The Remote Model Number on transmitter and receiver must be the same. 1b. The Remote Serial Number will be the same on a pre-paired remote set. If it is different, it will need to be paired (See page 8) 2.
PAGE 7
P6 6. CANOPY INSTALLATION Canopy 6-1. Canopy Align Holes Screw (2) 6-2. Key Hole (2) 6-4. Deco Ring Note: Two screws are installed on mounting bracket for canopy installation. 6-1. Push up canopy until two pre-installed screws on mounting bracket are engaged with two key holes on canopy. 6-2. Rotate canopy slightly until two pre-installed screws heads are engaged in the narrow end of key holes. 6-3.Tighten both screws. 6-4.
PAGE 8
P7 8. OPERATIONAL INSTRUCTION All the button pressed will have a Beep sound and the red indicator light will turn on. 8-1. ON/OFF - Fan 8-1. Press 8-5. Indicator button to turn the fan ON/OFF. Warning: DO NOT PRESS THE BUTTON FOR MORE THAN 4 SECONDS TO AVOID FACTORY RESET AND THE LOSS OF PRE-PAIRED PROGRAMING OF RECEIVER AND TRANSMITTER! 8-7. Light function 8-3. Reverse switch 8-2. Fan Speed (1-Low Speed 5 -High Speed) 8-4. Timer (1hr/4hrs/8hrs) 8-6.
PAGE 9
P8 9. REMOTE PAIRING PROCESS The Pairing Process is only necessary when there is an issue. Remote set is pre-paired from the factory and should not require the Pairing Process. A fan may need to have “Pairing Process” performed for the following issues. 1. Replacing the transmitter. 2. Replacing the receiver. 3. Multiple fans on the same circuit. (In multiple fans situation, each fan must be wired up individually for the Pairing Process; see step 9-1.) 9-1.
PAGE 10
P9 9-4. TO SET UP REMOTE FOR #2 FAN OFF Make sure to turn off power at breaker box. O FFO FFO FF Disconnecting wire from #1 Fan Disconnect the Black wires from #1 Fans and connect the Black wires back to #2 Fan that you remove from 9-3. Outlet Box Outlet Box (Disconnecting) Mounting Bracket Mounting Bracket #2 Fan #1 Fan #2 Fan is ready for setting Turn on power at breaker box and #2 Fan is ready for setting. ON OFF OFF OFF *See the remote control setting process for 9-1 to set up #2 Fan.