Vogue & Vogue Plus 3SA60 3SA60+LED This instruction contains 11 pages: Page 1: Foreword Page 2~3: Unpack and inspect parts contained Page 4~5: Notes before installation and Hanging system installation Page 5~6: Wire connection Page 7: Blade installation and Canopy installation and Light kit installation Page 8: Remote setting Page 9~11: Troubleshoot Net weight 8.7 KGS. 19.0 LBS.
READ AND SAVE THESE INSTRUCTIONS WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, PLEASE OBSERVE THE FOLLOWING : 1]. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning. 2]. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring. All electrical connections must be made in accordance with local codes, ordinances and/or the National Electric Code.
Unpack and inspect fan carefully to be certain all contents are included.
Unpack and inspect fan carefully to be certain all contents are included.
WARNING: blades should be at least 7 feet from floor Note 1: Note 2: Turn off power at breaker box to avoid possible electrical shock. Use metal outlet box suitable for fan support. Outlet box must support 35 lbs min. OFF OFF OFF 1. HANGING SYSTEM INSTALLATION 1A.Installing mounting bracket to ceiling outlet box 1 Install mounting bracket to outlet box in ceiling by using screws included with the outlet box and washers from the hardware bag. 2 Loosen the screws at mounting bracket.
1C. Hanging the fan 2 Rotate fan so that the groove on the ball engages 1 Lift fan assembly onto mounting bracket. the ridge in the mounting bracket. Mounting Bracket Mounting Bracket Ridge Ball Groove Fan Assembly 2. WIRE CONNECTION 2A. Insert receiver into mounting bracket NOTE: Do not sq u eeze all the wires while inserting the receiver into the mounting bracket. Receiver Mounting Bracket 2B-1.
2B-2.Making electrical wire connection FOR VOGUE PLUS (W/LIGHT) Follow diagram below and make sure that all exposed wires are secured inside wire nuts or terminal block. Note : Wires from house may vary in color and may not include ground wire ( green ). After wiring is completed, gently push wires into junction box with wire nuts pointing upward.
4. BLADE INSTALLATION Attach blades to fan assembly by using screws provided from hardware bag. (* Repeat until all 3 blades are installed firmly.) Blade Screw(3) & Spring Washer(3) Blade(3) Fan Assembly INSTALLATION FOR LED LIGHT COVER FOR VOGUE PLUS (W/LIGHT) 1 LED already pre-installed. 2 Align the grooves in the Light Cover to the tabs in the Collar and attach the Light Cover clockwise. Blade LED Groove Safety Light Cover (Do not open the safety light cover, when fan is in operation.
After completing the ceiling fan installation, install the 12V battery(included) in the hand-held Transmitter (see below FIG.2). Your fan is ready for remote control setting and operation. FIG.2 *NOTE: Your DC motor is equipped with an automatically learned type Remote control. The Remote control has been pre-set up and completed the learning/setting. The serial number sticker is paired on both Transmitter & Receiver. PLEASE DO NOT MIX THE SERIAL NUMBER! (See label on receiver and remote control cover.
Troubleshoot In general, the fan control is preset and should function normally, even if there are more than one fan in the same area. In the event of mixed paired remote & receiver, please do the following. Step 1. Make sure to turn off power at breaker box. First, switch the main power off and make sure fan has completely stopped. OFF O FFO FFO FF Step 2. To set up remote for #1 Fan 2-1.
Step 3. To set up remote for #2 Fan 3-1. Make sure to turn off power at breaker box. Switch the main power off and make sure fan has completely stopped. OFF O FFO FFO FF 3-2. Disconnecting wire from #1 Fan Disconnect the AC Black wires to the #1 Fans and connect the AC Black wires back to #2 Fan that you remove from Step 2-1. *See the remote control setting process for step 3-3.
Step 4. Reconnecting all fans 4-1. Make sure to turn off power at breaker box. Switch the main power off and make sure fan has completely stopped. OFF O FFO FFO FF 4-2. Connect wire to #1 Fan and #2 Fan should already be wired Outlet Box Mounting Bracket Outlet Box #1 Fan Mounting Bracket #2 Fan 4-3. Turn on the power from main switch and now each of these two fans are operated by its own remote individually.