Installation Sheet

ManualsBrandsTroy Lighting ManualsChandeliersJuniper 10 Light 42" Wide Chandelier with Hardback Linen Shades

F6179 JUNIPER LARGE CHANDELIER INSTALLATION INSTRUCTIONS

TROY LIGHTING

FIXTURE PREPARATION

1. Remove the fixture, parts and parts bag(s) from the carton.

NOTICE:

• Before discarding the carton, double check to

make certain that all parts are found.

CAUTION

•

••

• TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH

ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES.

•

••

• INSTALLATION AND MAINTENANCE OF THIS UNIT REQUIRES AN ELECTRICIAN OR

CERTIFIED FACTORY TRAINED TECHNICIAN.

•

••

• If an existing fixture is being replaced, remove it and note to which of the wires in the outlet box the fixture was attached.

DO NOT SEPARATE ANY OTHER WIRES THAT MAY BE IN THE BOX. DO NOT DAMAGE THE INSULATION OF OLDER WIRING.

In regular circumstances the BLACK wire will be the "Hot" lead and the WHITE wire will be the "Neutral" or "Common" lead

A GREEN or BARE COPPER wire is the "Ground". In older buildings it is always good practice to reconfirm the polarity of the wiring.

FIXTURE INSTALLATION

1. Attach the mounting strap to the outlet box. (The green screw should face the floor).

2. Remove the threaded ring from the screw collar loop. Fully thread the screw collar loop

onto the nipple. Thread the hex nut onto the nipple and the nipple into the mounting strap.

Place the canopy over the screw collar and against the ceiling. Adjust the nipple so that

of threads on the screw collar loop extend beyond the canopy. Tighten the hex nut against

the crossbar. Using the threaded ring, install the canopy. See Figure 1.

NOTICE

• The important safeguards and instructions outlined on this sheet cannot cover all possible conditions and situations that

may occur. it must be understood that common sense, caution and care factors that cannot be built into any product.

Caution and care must be supplied by the person(s) installing, operating and caring of this lighting fixture.

• This fixture is designed to be mounted on a correctly installed standard round or octagon box or a through wiring box with a

plaster frame. The box must be securely mounted to the structure of the building. The crossbar and hardware supplied should be

used. directly mounting the fixture to the outlet box may make it impossible to correctly align the fixture.

NOTICE:

CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO

CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE.

Canopy

Nipple

Hex nut

Screw Collar loop

Ring

Green screw

Mounting Strap

Outlet box

FIGURE-1

WARNING

DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE

READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.

Summary of content (2 pages)

PAGE 1
F6179 JUNIPER LARGE CHANDELIER INSTALLATION INSTRUCTIONS TROY LIGHTING WARNING DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION. CAUTION • TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. • INSTALLATION AND MAINTENANCE OF THIS UNIT REQUIRES AN ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
PAGE 2
3. Open the end links of the chain and attach the chain to the screw collar loop. Insert the lead wire to the stem then thread in the stem into the frame. See Figure-2. Hang the fixture on the chain at the desired height. Remove the excess chain close all links. Unscrew the threaded ring from the screw collar loop. Allow the ring and canopy to slide down the chain to the top of the fixture. See Figure-3. WARNING The use of chain pliers for opening and closing chain is required.