Datasheet

ManualsBrandsTRU COMPONENTS ManualsResistorsCermet resistor 22 kΩ SMD 0603 0.2 W 1 % 100 ±ppm/°C TC-HP03W5F2202T5E203 1 pc(s)

1. Scope:

This specification for approval relates to High Power Thick Film Chip Resistors

Ex.

3. Ratings:

Type

Power Rating

Max. Working Voltage

Max. Overload Voltage

Dielectric Withstanding Voltage

Temperature Range

Ambient Temperature

500 V

-55кД +155к

70 к

300 V

HP05

1/3W (0.33W)

150 V

300 V

500 V

HP03

1/5W (0.20W)

50 V

100 V

HP06

HP05

Nominal ResistancePower Rating Resistance toleranceType

1/5W (0.20W)

1/2W (0.50W)

1/3W (0.33W)

HP03

F,J 10ȍ

HP06

1/2W (0.50W)

200 V

400 V

The type designation shall be in the following form:

All part numbers in the coding below start with "TC-" and end with "203"

2. Type designation:

Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau

Datasheet

V1_0717_01_en

Summary of content (12 pages)

PAGE 1
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en 1. Scope: This specification for approval relates to High Power Thick Film Chip Resistors 2. Type designation: The type designation shall be in the following form: All part numbers in the coding below start with "TC-" and end with "203" Ex. Type Power Rating HP03 1/5W (0.20W) HP05 1/3W (0.33W) HP06 1/2W (0.50W) Resistance tolerance Nominal Resistance F,J 10ȍ 3.
PAGE 2
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en 3.1 Power rating: Resistors shall have a power rating based on continuous load operation at an ambient temperature of 70 к . For temperature in excess of 70 к , The load shall be derate as shown in figure 1. Figure 1 3.
PAGE 3
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en High Power Thick Film Chip Resistors 4. Construction : 5. Power rating and dimensions Dimension : Dimension (mm) Type L HP03 1.60 ± 0.10 HP05 2.00 ± 0.15 HP06 3.10 ± 0.15 W 0.80 + 0.15 - 0.10 1.25 + 0.15 - 0.10 1.55 + 0.15 - 0.10 H Ɛ1 Ɛ2 0.45 ± 0.10 0.30 ± 0.20 0.30 ± 0.20 0.55 ± 0.10 0.40 ± 0.20 0.40 ± 0.20 0.55 ± 0.10 0.45 ± 0.20 0.45 ± 0.
PAGE 4
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en High Power Thick Film Chip Resistors 6. Marking : 6.1 Resistors A. ± 5% Tolerance 0603, 0805, 1206 : the first two digits are significant figures of resistance and the third onedenoted number of zeros. Ex. 333 33KӨ B. For ohmic values below 10 Ө Ex. 2R2 2.2Ө C. For E-96 series [±1% (F) tolerance] in 0603 size 3 digit system (due to space restrictions) please refer to page 8 for coding formula Ex.
PAGE 5
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en High Power Thick Film Chip Resistors Mutiplier Code : Code A ˃ Multiplier ˄˃ B C F G H ˄ ˅ ˆ ˇ ˈ ˉ ˊ ˄˃ ˄˃ ˄˃ ˄˃ ˄˃ ˄˃ ˄˃ Coding D E Formula XX Example : X ˀ˄ ˄˃ 10.2KӨ = 102 X Y Z ˀ˅ ˀˆ ˄˃ X 02 ˄˃ 10˅ Өʳʳʳ= 02C C -1 Resistance Code Multiplier Code 33.
PAGE 6
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en High Power Thick Film Chip Resistors 7. Performance specification : Characteristics Test Methods ( JIS C 5201-1 ) Limits Dielectric No evidence of flashover 4.7 Clamped in the trough of a 90͠ metallic v-block withstanding mechanical damage, arcing or and shall be tested at ac potential respectively specified voltage insulation break down in the type for 60-70 seconds 4.
PAGE 7
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en High Power Thick Film Chip Resistors 7. Performance specification : Characteristics Test Methods ( JIS C 5201-1 ) Limits Wave Solder: Test temperature of solder: 245°C ±3°C dipping time in solder : 2-3 seconds. Refolw: Solderability 95 % coverage Min. 4.18 Dip the resistor into a solder bath having Soldering heat Resistance change rate is: a temperature of 260°C±3°C and hold it for 10±1 ± (1.0%+0.
PAGE 8
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en High Power Thick Film Chip Resistors 7. Performance specification : Characteristics Humidity Limits Test Methods ( JIS C 5201-1 ) Resistance change rate is 4.24 Temporary resistance change after 240 hours ± 5% (3.0% + 0.1Ө) Max. exposure in a humidity test chamber controlled at ± 1% (0.5% + 0.1Ө) Max. 40±2°C and 90-95% relative humidity 7.
PAGE 9
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en High Power Thick Film Chip Resistors 8. Packing specification : 8.1 Taping Dimension (mm) A. Paper taping Type A ± 0.2 B ± 0.2 C ± 0.05 ӿD +0.1 E ± 0.1 F ± 0.05 G ± 0.1 W ± 0.2 T ± 0.1 -0 HP03 1.10 1.90 2.0 1.5 1.75 3.5 4.0 8.0 0.67 HP05 1.65 2.40 2.0 1.5 1.75 3.5 4.0 8.0 0.81 HP06 2.00 3.60 2.0 1.5 1.75 3.5 4.0 8.0 0.
PAGE 10
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en High Power Thick Film Chip Resistors 8.2 Reel Dimension (mm) Type Packaging Quantity Per Reel A ± 0.5 B ± 0.5 C ± 0.5 D±1 M±2 W±1 HP03 Paper 5,000 pcs. 2 13 21 60 178 10 HP05 Paper 5,000 pcs. 2 13 21 60 178 10 HP06 Paper 5,000 pcs. 2 13 21 60 178 10 Remark : M M 10,000pcs. / Reel = 255 ± 2mm 20,000pcs.
PAGE 11
Distributed by Conrad Electronic SE • Klaus-Conrad-Str.
PAGE 12
Distributed by Conrad Electronic SE • Klaus-Conrad-Str. 1 • D-92240 Hirschau Datasheet V1_0717_01_en High Power Thick Film Chip Resistors Environment Related Substance This product complies to EU RoHS directive, EU PAHs directive, EU PFOS directive and Halogen free. Ozone layer depleting substances. Ozone depleting substances are not used in our manufacturing process of this product.