User Manual

ManualsBrandsTruxedo ManualsAutomotiveTruXedo Deuce Soft Roll-up Truck Bed Tonneau Cover | 746901 | fits 10-18 Ram 2500/3500 6'4" Bed

P/N 1117648 Rev D

___

Owner’s & Installation Manual

READ INSTRUCTIONS - Failure to assemble cover properly will void warranty.

Damaged or missing parts?

Call

1-877-878-9336

Mon - Fri 8 am - 5 pm CT

Parts will be shipped to you factory direct.

Do not return kit to place of purchase.

Tools Required:

-3/8” Rachet

-1/2”, 9/16” Socket

-Tape Measure

- Pencil (For marking Locations)

- Small Spring Clamps (Optional,

used to hold rails in place while

clamping)

TruXedo

Deuce is a registered United States trademark of TruXedo. Patents pending.

2209 Kellen Gross Dr., Yankton SD 57078

Phone: 1-877-TRUXEDO (1-877-878-9336) Fax: (605) 664-9304

Web Site: http://www.truxedo.com

OWNER’S MANUAL

PICKUP BED COVER

Summary of content (10 pages)

PAGE 1
Owner’s & Installation Manual Read Instructions - Failure to assemble cover properly will void warranty. OWNER’S MANUAL Tools Required: -3/8” Rachet -1/2”, 9/16” Socket -Tape Measure - Pencil (For marking Locations) - Small Spring Clamps (Optional, used to hold rails in place while clamping) Damaged or missing parts? Call 1-877-878-9336 Mon - Fri 8 am - 5 pm CT Parts will be shipped to you factory direct. Do not return kit to place of purchase. Pickup Bed Cover 2209 Kellen Gross Dr.
PAGE 2
Cover Assembly f o ox t n b o ck fr ru t Driver’s Side Underbody Rail Driver’s Side Rail Assembly Passenger’s Side Underbody Passenger’s Side Rail Assembly Block Seal (x2) Clamps (x8) Attach Foam Block Seals. Peel white paper backing off and attach foam corner block seals. step 1 Fron ad t Bul lkhe nt Bu Fro khea d Front Bulkhead 1/4” Driver Side step 2 1/4” Passenger Side Attach Underbody Rail and Clamp Components.
PAGE 3
step 2-A Attach driver and passenger side underbody rails, see note 1 & 2 for installation hints. Fro ad he nt k l Bu Bu lkh nt o ea r F d Compress Block Seal 30 1/4 ” /4” 1 30 Driver’s Side Note 1 Co mp Passenger Side re Note 2 ss While clamping press down COMPRESS SEAL Bl oc kS Level ea l FOR BEST CLAMPING MOUNT CLAMP HIGH AS POSSIBLE step 3 ADJUSTABLE CLAMP Position driver and passenger rails.
PAGE 4
step 3-A Position and install driver side rail assembly with clamps, see note 1 and 2 for installation hints. SEAL COMPRESSED While clamping press down to compress side seal LEVEL ADJUSTABLE CLAMP Note 2 Note 1 Driver’s Side FOR BEST CLAMPING MOUNT CLAMP HIGH AS POSSIBLE Note 2 Driver’s Side Shown 3/8” ! Tailg a te Note 1 If rear seal is not slightly compressed then reposition assemblies rearward slightly.
PAGE 5
step 4-a Attach cover assembly to the driver and passenger side rails as shown. Insert and Rotate up. Lock both driver and passenger Simultaneously insert front header in both driver and passenger side header stops. step 5 ! side. Rotate attached cover assembly over to the cab and engage strikers into latch brackets. Installer should be inside the truck box when rotating assembly over to the front. Striker Pin ! Use caution, cover assembly is heavy.
PAGE 6
step 6 Rotate release levers to the left before connecting outside tie-bars. Rotate both levers to the position as shown. Left step 7 Connect driver and passenger short tie-bars as shown below. Driver side shown, repeat procedure for passenger side Rotate Tie-bars into position as shown 7A 7B 7c Connector End 7d Ball Socket Remove anti-spin tape Position both release levers to the left before attaching outer tie-bars, see step 6.
PAGE 7
step 8 How to close the cover. Cab End Tailgate Unroll cover toward the tailgate. Rotate rear header into the header stops and press down to lock toggle into header. Header Header Stop Cover closed and toggle locked in header. Toggle step 9 After cover is closed secure the hook and loop fastener strips on both sides of truck. step 10 1/8” Set cover tension during the warmest part of the day.
PAGE 8
step 13 Closing Cover ! Latches are secure when striker pins return back to 90 deg. Open 90 Deg Close Always lift upward on cover front after closing to make sure cover is securely latched. ! Striker Pin Striker Pin step 14 How to lock cover closed for security. locked Unlocked Driver Side Security Lock Security Lock Location The Deuce cover can be locked while the cover is rolled up or in the open position as shown above.
PAGE 9
14 21 17 16 18 16 16 33 15 22 23 3 4 10 24 33 10 25 6 13 10 7 28 9 8 10 31 27 14 5 2 19 2 20 26 1 2 26 35 31 36 20 12 34 21 11 34 29 30 33 18 22 32 19 33 25 TRUXEDO® deuce REPLACEMENT PARTS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ___*___ Deuce® Replacement Cover 17 ___*___ Cross Bow Tubes Assembled 18 ___*___ Safety Strap 19 1704715 Extruded Reatainer Loop 20 ___*___ Black Front Header 21 1117594 Header Guide Retainer Assy 22 1704707 Header Guide_2011 23 1704879 Le
PAGE 10
Trouble shooting front latch won’t release either side: -Adjust tie-bar connector ends outward to eliminate slack in entire linkage mechansim. See Step 7. Front Release levers, Linkage and striker pins seem to bind: -Lubricate all linkage pivot points with mineral oil. Lubricate striker pins and pivot base with a graphite dry liquid lubricant. front of cover will not stay latched down: -Make sure striker pins are returning to closed 90 degree position. See Step 13.