TWIN EAGLES GAS GRILL INSTALLATION, USE AND CARE MANUAL P/N: 19198L (08/20) MODELS: TEBQ30G-C TEBQ30R-C TEBQ36G-C TEBQ36R-C TEBQ42G-C TEBQ42R-C TEBQ54RS-C
A special message to our customers… Congratulations on the purchase of your Twin Eagles grill! Our products are engineered for precision and designed for style. Each Twin Eagles grill is manufactured in the USA at our own state of the art facility in California. This manual will give you easy to follow instructions for installing, operating and maintaining your grill. We recommend reading this manual before your first use to ensure safety, proper care and operation.
IMPORTANT SAFETY INSTRUCTIONS WARNING! Read this manual carefully and completely before using your grill to ensure proper operation, proper installation, proper servicing and to reduce the risk of fire, burn hazard and/ or other injury. AVERTISSEMENT! Lire ce manuel avec soin et en entier avant l’utilisation de votre barbecue afin d’en assurer un fonctionnement, une installation et un entretien adéquats et réduire le risque d’incendie, de brûlures et d’autres blessures.
GENERAL SAFETY REQUIREMENTS • • • • • • • • • • • • • The installation of this appliance must conform with local codes or, in the absence of local codes, either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1 or Propane Storage and Handling Code, B149.
TABLE OF CONTENTS GETTING STARTED…………………………………………………………………………………..…….……… GAS REQUIREMENTS o GAS SAFETY REQUIREMENT…………………………………………………………….…… o LP GAS HOOKUP………….………………………………………………………..…………… o PORTABLE LP CONNECTION………….………………………………..…………………..… o NATURAL GAS INSTALLATION……………………………………..……………………….. o LEAK TEST……………………………………………………………………..………………... o ELECTRICAL REQUIREMENTS……………………………………………………………….. LOCATING THE GRILL o CLEARANCE TO COMBUSTIBLE CONSTRUCTION……………………………..….
GETTING STARTED 1. Remove all packaging materials, labels and protective plastic film. DO NOT LEAVE UNIT IN THE SUN WITH PROTECTIVE PLASTIC FILM ON FOR A LONG PERIOD OF TIME AS IT WILL BECOME DIFFICULT TO REMOVE THE FILM. 2. Check to ensure that all grill accessories listed below are included. TEBQ TEBQ TEBQ TEBQ TEBQ TEBQ TEBQ 30G 30R 36G 36R 42G 42R 54RS Basting Pan 1 1 1 1 Hex Grate, Stainless Steel 2 2 3 3 3 3 4 Large Briquette Tray Assy. (Standard Grill) 1 1 2 2 2 2 Small Briquette Tray Assy.
5. Get familiar with the knobs and burners identification below. TEBQ30 Grill Burner Sear Zone (Opt) TEBQ36 Rotisserie (TEBQ30R) Rotisserie (TEBQ36R) Grill Burner TEBQ54RS TEBQ42 Grill Burner Sear Zone (Opt) Grill Burner Sear Zone (Opt) Grill Burner Rotisserie (TEBQ42R) Grill U-Burner (Standard) located underneath the briquette trays. Grill Burner Sear Zone Left Rotisserie Optional Sear Zone Burner (Standard on TEBQ54RS Only) usually located on the left side.
GAS SAFETY REQUIREMENTS Each appliance is set and tested at the factory for the type of gas supply to be used. Identify the type of gas, either natural gas (NG) or Liquid Propane (LP) gas and make sure that the marking on the data plate (rating plate) matches the gas being supplied to the grill. This information is found on the data nameplate, located on the bottom right hand side of the firebox near the regulator.
LP GAS HOOK-UP CAUTION: Provide adequate ventilation holes in the enclosure for safety purposes in the event of a gas leak. Install the factory-supplied hose and regulator assembly as shown. Connect the 3/8” flare end of the hose to the grill coupling using a ¾” open wrench. Do not apply pipe sealant to the 3/8” flare connection. Connect the regulator to the LP cylinder hand tighten it, do not use a wrench. Check for leaks using soapy water solution. (Reference page 7 for leak test procedure).
PORTABLE LP CONNECTION One of the many features of the TWIN EAGLES grill base is the pullout slide pan for easy access to the LP gas tank. 1) To install the gas cylinder, pull out the slide pan and place the cylinder onto the pan. 2) Tighten the tank holding screw to secure the gas cylinder in place. 3) Check to ensure that the tank’s gas valve on top of the cylinder is closed. 4) Connect the LP regulator (included) to the cylinder and hand-tighten only.
NATURAL GAS INSTALLATION A typical natural gas installation is shown below. Make sure that the factory-supplied regulator is used and installed with the arrow mark on the regulator pointing towards the gas grill. Use only pipe sealants that are approved for use with natural and LP gases. An installer-supplied gas shutoff valve must be installed in an accessible location.
LEAK TEST CAUTION BEFORE TESTING: • • • • • NEVER USE THE GRILL WITHOUT FIRST LEAK TESTING THE GAS CONNECTIONS. WARNING: DO NOT USE OPEN FLAME TO CHECK FOR LEAKS. USE OF AN OPEN FLAME COULD RESULT IN A FIRE, EXPLOSION AND BODILY HARM. DO NOT SMOKE WHILE PERFORMING THE LEAK TEST! To prevent fire or explosion hazard, DO NOT use or permit sources of ignition in the area while performing a leak test. Perform leak test outdoors only.
ELECTRICAL REQUIREMENTS The appliance should only be taken apart by a qualified technician, or electrical shock may occur. It is rated at 120V, 60Hz, and 4A. REMINDER: Keep any electrical supply cord and the fuel supply hose away from any heated features. ! WARNING ! Electrical Grounding Instructions: This outdoor gas cooking appliance is equipped with a three prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three prong outlet.
LOCATING THE GRILL This gas appliance is designed and certified for outdoor use only. Do not locate this grill under overhead unprotected combustible surfaces. When installed under overhead combustible surfaces, a certified ventilating hood wider than the appliance shall be installed with a minimum distance of 36 inches above the cooking surface. CAUTION should be taken when grills are used near glass, vinyl siding or other temperature sensitive construction materials.
Windy Conditions Your TWIN EAGLES grill has been designed and engineered to produce intense heat that sears food quickly, locking in the foods natural moisture and flavor. The grills burners require air for efficient burner combustion. This fresh air is pulled through a vent in the front of your grill and the intense hot air produced by the burners is expelled through a vent in the rear. If you are using your grill in windy conditions, the wind can disrupt this important airflow.
INSULATION JACKET CUT-OUT DIMENSIONS INSULATING JACKET WARNING: Do not build the grill under overhead unprotected combustible construction. If the grill is to be placed into combustible enclosure, an approved insulating jacket is necessary to prevent fire, property damage and bodily injury. Use only Twin Eagles insulating jacket. IMPORTANT: When installing use front right knockout to keep power cord cool.
GRILL CUT-OUT DIMENSIONS This is for non-combustible construction. For combustible construction refer back to previous page.
ASSEMBLY INSTRUCTIONS Your Twin Eagles Grill is fully assembled and tested in the factory and requires no major assembly in the field. For the purpose of safe shipping and transit, some parts such as the briquette trays and rotisserie components are wrapped inside the grill and require minor assembly. TO INSTALL BRIQUETTES TRAYS 1. Put briquette trays into the grill above the burner, as shown by placing the flash-tube-hole on the front. 2.
ASSEMBLY INSTRUCTIONS - CONTINUED CORRECT BURNER INSTALLATION: The gas valve orifice is completely inserted inside the venturi. INCORRECT BURNER INSTALLATION: The gas valve orifice is out of position and is not inserted into the burner. The orifice is out of position. The orifice is touching the tip of the burner venturi.
BURNER FLAME / AIR SHUTTER ADJUSTMENT Each grill burner is tested and adjusted at the factory prior to shipment; however, variations in the local gas supply may make it necessary to adjust the burners. The flames of the U-burners should be visually checked. Flames should be blue and stable with little to no yellow tips, no excessive noise or lifting. If any of these conditions exist, remove the burner and check to see if any air shutter or burner ports are blocked by dirt, debris, spider webs, etc.
OPERATING INSTRUCTIONS BEFORE LIGHTING THE GRILL ! WARNING ! DO NOT ATTEMPT TO LIGHT THE GRILL IF YOU SMELL GAS. • • • • WARNING! IT IS CRITICAL THAT THE GAS BURNERS ARE PROPERLY INSTALLED WITH THEIR ORIFICES INSIDE THE BURNERS AIR SHUTTERS. If not properly installed, gas may leak outside of the burner that could lead to fire, potential damage to your grill and bodily injury. (Please refer to Page 14 for correct burner installation) Inspect the gas supply piping or hose prior to turning the gas ON.
Match/BBQ Lighter Lighting Instructions: If there is no electrical power supply available or if hot surface igniter will not light the burners, the burners can be lit manually using a lighted long match, taper or BBQ lighter. 1. Push and turn the knob counter-clock-wise to the biggest flame marking on the bezel. Hold the knob pushed in for 5 seconds. 2. Insert a lit match or BBQ lighter through the grates and near the top of the flashtube. Once you see or hear a flame you can release the knob.
USING THE ROTISSERIE 1. Insert the food on the middle of the spit rod and then secure For small load it with the meat holders on both ends by tightening the thumb screws on the meat forks. If multiple pieces of food will be cooked at the same time, make sure the load is evenly balanced on the spit rod. Proper weight balancing will ensure evenness of cooking and prolong the life of the rotisserie motor. 2. Insert the spit rod in the rotisserie at desired cooking position.
USING THE SMOKER BOX The Twin Eagles sealed smoker box can hold dry wood chips or liquids for hickory, mesquite or your favorite wood chips to give meat a smoky flavor. 1) Remove a grate. 2) Remove a half size briquette tray where there is no flashtube and replace it with the smoker box. 3) Add your favorite soaked wood chips. 4) Wait for the chips to start smoking and you are ready to start grilling.
CLEANING & MAINTENANCE IMPORTANT Stainless Steel & General Product Care To keep your TWIN EAGLES products free of surface corrosion and in good working order, it is important to take additional precautions under certain conditions. If your TWIN EAGLES products are located in corrosive conditions, such as: • A coastal environment where corrosive salty air is present. • Near a swimming pool, hot tub or water feature with exposure to corrosive pool chemicals and/or chlorinated water.
Specks of grease can gather on the surface of the stainless steel and get baked-on. These can be removed by using a mild abrasive pad with a stainless steel cleaner. Use the mildest cleaner and always scrub in the direction of the grain. Do not use steel wool to clean the grill. Do not use abrasives on the polished highlights. Be extra careful when cleaning around the highlights. Metal polisher or mild chrome cleaner can be used to bring back the luster on highlights.
BURNERS Burners are made of heavy gauge stainless steel and can be soaked in water and cleaned with wire brush. Check every port hole for clogs. Use a wire pin to clean out clogged ports. Make sure the burner is dry before installing it back to the grill. INFRARED SEAR BURNER The infrared burner has stainless housing and a protective screen. The protective screen helps reflect heat up to the cooking surface and also catches any food particles from landing on the ceramic burner.
EXPLODED VIEW 23
REPLACEMENT PARTS LIST Item No.
REPLACEMENT PARTS LIST - CONTINUED Item No.
WIRING DIAGRAM 26
TROUBLESHOOTING GUIDE BEFORE CALLING FOR SERVICE: If your Twin Eagles grill does not function properly, use the following troubleshooting guide before contacting your dealer for service. The troubleshooting guide may save the cost of a service call and the inconvenience of being without your grill. PROBLEM Grill will not light. WHAT TO DO 1. Push in the knob and verify that the igniter glows. 2. If the igniter does not glow verify proper power supply. GFCI 120V. a. Purge the line of any trapped air. b.
TWIN EAGLES GRILL WARRANTY LIMITED LIFETIME WARRANTY: Twin Eagles warrants the stainless steel main burners, hexagonal grates and all fabricated stainless steel components, to be free from defects in materials and workmanship under normal residential use for the lifetime of the product. This warranty excludes discoloration, surface scratches, weather and atmospheric related staining, and minor surface rust and oxidation which are normal conditions and are to be expected with any outdoor product.
THIS PAGE IS INTENTIONALLY LEFT BLANK
HOW TO OBTAIN SERVICE For service, please contact your TWIN EAGLES dealer or call TWIN EAGLES direct at (800) 789-2206 or (562) 802-3488 or fax (562) 802-3391 Mailing address: Twin Eagles, Inc. 13259 East 166th Street Cerritos, CA 90703 Visit us at www.twineaglesgrills.
Cut Here Place Postage Here Customer Service ATTN: Warranty Department 13259 East 166th Street Cerritos, CA 90703 Fax no.