Instruction Manual

ManualsBrandsTycon Power ManualsPower suppliersTPDIN-Monitor-WEB

TPDIN-Monitor-WEB

Web Based Monitor and

Control

▫ Remote Power Stations

▫ Backup Power Systems

▫ Solar Systems

▫ Wind Powered Systems

▫ Industrial Sense & Control

▫ Process Automation

Congratulations! on your purchase of the TPDIN-Monitor-WEB

PowerSens™ System Monitor. Please take a moment to review

this Qwik Install Guide before installation.

Recommended Tools and Supplies: Small Flat Blade Screwdriv-

er, 35mm x 7.5mm DIN Rail

Qwik Install

STEP 0: The TPDIN-Monitor-WEB can be used to monitor Qty 4 1V-

80V Voltages, 4 Currents ( Qty 2 +/- 10A and Qty 2 +20A) and two tem-

peratures (1 internal and 1 external). There are 4 10A relays that can be

used to control power to 4 devices. Two of those relays can be auto-

matically set based on a temperature or voltage value. Two can be op-

erated automatically based on a ping watchdog or time control.

STEP 1: Install the TPDIN-Monitor-WEB to a suitable DIN rail mount.

STEP 2: Connect the voltages to be monitored to the V1—V4 voltage

ports. The green connector needs to be removed to be able to access

the wire terminal screws. The green connectors are numbered 1-7 and

should be re-installed back in their proper position. Voltages between 1

and 80volts DC can be monitored.

STEP 3: Connect the currents to be monitored to the I1-I4 current ports.

I1 and I2 can read currents from 0.1 to 20A. I3 and I4 can read positive

or negative currents to +/-10A. These can be used to measure current

flowing into and out of a battery to see if the battery is charging or dis-

charging. The green connectors may need to be removed to be able to

access the wire terminal screws. The green connectors are numbered

1-7 and should be re-installed back in their proper position.

Summary of content (8 pages)

PAGE 1
TPDIN-Monitor-WEB Web Based Monitor and Control ▫ Remote Power Stations ▫ Backup Power Systems ▫ Solar Systems ▫ Wind Powered Systems ▫ Industrial Sense & Control ▫ Process Automation Congratulations! on your purchase of the TPDIN-Monitor-WEB PowerSens™ System Monitor. Please take a moment to review this Qwik Install Guide before installation. Recommended Tools and Supplies: Small Flat Blade Screwdriver, 35mm x 7.
PAGE 2
STEP 4: Connect any power to devices you want to be under relay control to the CHI—CH4 relays. The relays are normally closed relays so activating the relay will open the relay. STEP 5: Connect the External Temperature sensor to the included green wire terminal connector. Connect the wires to IN– and IN+ terminals. Plug the wire terminal connector to the “Temp.” connector location. Locate the external temperature sensor where you want to measure external temperatures.
PAGE 3
STEP 10: Open the System Page. You should add meaningful labels to all the Voltages, Currents, Relays and Temperatures that you are using. You can also change various settings on this page. Relays: Relays are normally closed to save power when “on”. If you want them to be initially open at power-up, check the box that says “Initial Off”. Cycle Delay: This controls how long the relay stays in the opposite state when cycle is clicked on the Monitor Screen.
PAGE 4
STEP 11: Open the Control Page. This is where you can set the relay Ping Control or Time and Temperature or voltage controls. You can set up the EMAIL server and set various email triggers. Relays 1 and 2: Time Control: Set the On time and Off time in 24hr format. Note: Time control overrides Ping Control and Manual control. Ping Control: Set the IP Address to ping. Set the ping frequency (Every). Setting the frequency to zero disables the ping.
PAGE 5
change state when voltage goes outside the range. Temperature set takes priority. Email Alerts: Set the Email server: ie; smtp.1and1.com Note: GMAIL accounts won’t work because they require SSL security when sending emails. Set the email account user name and password. Leave user name blank to force no authentication. Check the “Use Username as From Field” checkbox (recommended) to have the emails sent from the username which is usually an email address.
PAGE 6
State Of Charge Sealed or Flooded Lead Acid GEL Battery AGM Battery 100% 12.7+Volts 12.9+Volts 12.8+Volts 75% 12.4 Volts 12.7 Volts 12.6 Volts 50% 12.2 Volts 12.4 Volts 12.3 Volts 25% 12.0 Volts 12.0 Volts 12.0 Volts 10% 11.8 Volts 11.8 Volts 11.8 Volts 5. Operating Power: The TPDIN-Monitor-WEB has extremely low operating power, typically less than 3W. The relays are normally closed type so in typical operation they don’t take any power until they are energized.
PAGE 7
Connector Pinouts NOTES 7
PAGE 8
Limited Warranty The TPDIN-Monitor-WEB products are supplied with a limited 24 month warranty which covers material and workmanship defects. This warranty does not cover the following: ▫ Parts requiring replacement due to improper installation, misuse, poor site conditions, faulty power, etc. ▫ Lightning or weather damage. ▫ Physical damage to the external & internal parts. ▫ Products that have been altered, or defaced.