Installation Guide C2275DWR — Combo® Drawer Refrigerator/Freezer/Ice Maker www.U-LineService.com Phone (414) 354-0300 • FAX (414) 354-7905 Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696 OnlineService@U-Line.
C2275DWR — Ice Maker/Refrigerator Contents Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clearances Information . . . . . . . . . . . . . . . . . . . . . . . . . Other Site Requirements . . . . . . . . . . . . . . . . . . . . . . . . No Custom Drawer Panels . . . . . . . . . . . . . . . . . . . . . . .
C2275DWR — Ice Maker/Refrigerator General Precautions 2 Inspect and Plan Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide: You have received a carton containing your C2275DWR Combo Drawer Model Ice Maker/Refrigerator with a package inside containing a Use and Care Guide, a Product Registration Card, water connection parts and Anti-Tip Kit. Complete and mail the Product Registration Card or register online at www.
C2275DWR — Ice Maker/Refrigerator Exterior Cleaning 3 Prepare Site (As Required) Your U-Line product has been designed for built-in installation. Your unit does not require additional air space for top, sides or rear. However, the front grille must NOT be obstructed and clearance is required for water and electrical connections in the rear. Overlay Models: • The drawers, grille and cabinet may be cleaned with a mild detergent and warm water solution. Do not use solvent-based or abrasive cleaners.
C2275DWR — Ice Maker/Refrigerator Product Dimensions Clearances Information The unit must be installed in a wall or under a countertop to allow for the installation of the Anti-Tip Kit (see Page 14). 25-13/16" Including Handle 23-11/16" WARNING 34-1/8" The Anti-Tip Kit must be installed on this unit before it is used. Never use the drawers as steps or as a shelf to support more than the drawers’ contents. Serious personal injury could occur.
C2275DWR — Ice Maker/Refrigerator Other Site Requirements The drawer unit can be installed with an appliance or fixture located in front of it, as long as there is adequate clearance for the drawer to be opened and removed when servicing (see Figure 4). Power Supply The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A circuit (normal household current). See Electrical Specifications on Page 13.
C2275DWR — Ice Maker/Refrigerator Drawer Panel Installation 4 Prepare and Install Drawer Panel Install the insert as follows: (Overlay Units Only) CAUTION Two types of custom drawer panels can be installed on your Overlay unit to harmonize with or accent the surrounding décor: Custom 1/4" Inserts or Full Overlays. Overlay units may also be installed with no custom drawer panel. Use care when handling the insert. Insert edges may be sharp. 1. Open drawer.
C2275DWR — Ice Maker/Refrigerator Full Overlay Drawer Panels Attaching the Full Overlay Panel Drawer Panel Preparation 1. If user-supplied cabinet handles will be used, attach their hardware to the overlay panel at this time. Full overlay drawer panels completely cover the drawer fronts and handles to give a built-in appearance. Overlay units are shipped ready for full overlay installation.
C2275DWR — Ice Maker/Refrigerator CAUTION 5 Adjust Drawers It is important to ensure that all drilled holes are drilled to the correct depth in order to avoid splits in the wood when hardware is installed. Checking Drawer Alignment The unit’s drawers are aligned at the factory before shipment. However, their alignment could have been disturbed during shipment or during overlay panel installation. 4. Remove tape adjoining the panels and enlarge the five holes in the overlay panel using a 0.
C2275DWR — Ice Maker/Refrigerator Adjusting Drawer Alignment Minor Adjustment: Note: The mounting holes on the slide are slightly larger than the screws’ diameter. WARNING SHOCK HAZARD — The unit must be unplugged from the wall outlet during drawer removal, adjustment and re-installation. 1. Loosen the slide’s mounting screws. Drawer Removal 2. Push the slide backward. 1. Confirm that the unit is unplugged from wall outlet. Mounting Screw Push Slide Backward 3. Retighten the screws. See Figure 15.
C2275DWR — Ice Maker/Refrigerator Minor Adjustment: Minor Adjustment: Note: The mounting holes on the slide are slightly larger than the screws’ diameter. Note: The mounting holes on the slide are slightly larger than the screws’ diameter. Screws Should Be Loose 1. Loosen one slide’s mounting screws. 1. Loosen one slide’s mounting screws. 2. Level the slide. 2. Push the slide upward or downward to match the position of the other slide. 3. Retighten the screws. See Figure 18. 4.
C2275DWR — Ice Maker/Refrigerator 2. Locate the compression fitting and ferrule packed with the unit. Slide the compression fitting and ferrule over the 1/4-inch Outside Diameter water supply line. Do not use thread sealing compound or tape. Using two wrenches, tighten the compression fitting on the supply line (see Figure 24). 6 Prepare Plumbing Plumbing installation must observe all state and local codes. All water connections MUST BE made by a licensed/ qualified plumbing contractor.
C2275DWR — Ice Maker/Refrigerator 7 Prepare Power Supply 8 Level the Unit Electrical Specifications Leveling Information CAUTION IMPORTANT It is extremely important that the unit is level. If it is not level, the ice mold will not fill evenly. Electrical installation must observe all state and local codes. This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a qualified electrician. 1.
C2275DWR — Ice Maker/Refrigerator 9 Install the Unit Horizontal Mounting (Left Side Shown) Countertop or Wall Header Installation of the C2275DWR 1. Plug in the power cord. B 2. Open the top drawer.Press and hold the POWER icon to turn the unit OFF. (see Figure 31,1) Note: If the unit is NOT turned OFF, water will immediately start flowing into unit when it is first plugged into the electrical outlet and water supply is on. A 3. Open the water supply valve in the main water source. 4.
C2275DWR — Ice Maker/Refrigerator 4. Using two of the screws (C) supplied, fasten the screws through the bracket and into the counter, cabinet or wall. 10 Start-Up for the First Time IMPORTANT Initial Start-Up Certain cabinets or countertops may require special fasteners or additional wood blocking to anchor properly. All U-Line units are shipped from the factory with the controls that are preset. No initial adjustments are required.
C2275DWR — Ice Maker/Refrigerator Start-Up Troubleshooting Electronic Control Panel The electronic control with digital display (Figure 31) is located in the top drawer. It is configured to show a single temperature continuously. This set-point temperature is a base number used by the controller to maintain the temperature zone in your unit. The factory set-point is 38°F for the top drawer which will show when the unit is first powered up. The factory set point for the ice compartment is 0°F.
Who to Call Service Information If the need for service arises, call the U-Line Customer Care Center directly @ 800-779-2547. To ensure accurate assistance, please have your Model Number and Serial Number and an explanation of the problem.The Model and Serial Number plate is located inside unit at upper right hand corner. If you need to locate a service company, you can go online at www.U-LineService.com and search for a service company by zip code.
