INSTALLATION GUIDE ® 2000 SERIES DRAWER MODELS U-2275DWRCOL-00 U-2275DWRCOL-02 U-2275DWRCS-00 U-C2275DWROL-00 U-C2275DWRS-00 The American Built-In Undercounter Leader Since 1962 U-LINE.
Table of Contents 1 - Safety Precautions Safety Alert Definitions.........................................................................................................................................1 General Precautions ..............................................................................................................................................1 2 - Inspect & Plan Product Registration ........................................................................................................
General Precautions 1 Safety Precautions Use this appliance for its intended purpose only. Follow these general precautions with those listed throughout this guide: NOTICE • PLEASE READ all instructions before installing, operating, or servicing the appliance. • Proper installation procedures must be followed when completing an installation or relocation of a unit. An INSTALLATION GUIDE for the unit, providing complete installation information, is available from U-Line Corporation direct.
Tools / Material Required 2 Inspect & Plan • Screwdrivers — slotted and Phillips head (If installing a 3/4" Full Overlay panel) • 3/4" overlay frame material • Cutting Tools Product Registration • Drill & Drill Bits You have received a carton containing your U-Line Combo Drawer Model Ice Maker/Refrigerator or U-Line Refrigerator with a package inside containing a Use and Care Guide, a Product Registration Card, water connection parts and Anti-Tip Kit.
C2275DWR Series 3 Prepare Site Your U-Line product has been designed for either free-standing or built-in installation. When built-in, your unit does not require additional air space for top, sides, or rear. However, the front grille must NOT be obstructed and clearance is required for an electrical connection in the rear. 24" 34-1/4" to 35-1/8" NOTICE • Unit can NOT be installed behind a closed cabinet door. 7" ! WARNING 24-1/4" 1-1/2" SHOCK HAZARD — Electrical Grounding Required.
C2275DWR & 2275DWRC 4 Product Dimensions 2275DWRC C2275DWR 24" 24" 23-1/4" 23-1/4" 33-7/8" 33-7/8" 3-7/8" 3-7/8" Black Black 24" 24" 23-3/8" 23-3/8" 33-7/8" 33-7/8" 3-7/8" Stainless Steel 3-7/8" Stainless Steel 4 u-line.
Other Site Requirements 5 Clearance Information Power Supply The unit must be installed in a wall or under a counter-top to allow for the installation of the Anti-Tip Kit (see page 13). The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A circuit (normal household current). See Electrical Specifications. Water Supply ! WARNING The unit requires a 1/4-inch OD water supply line and a shut-off valve. For more information see page 12.
6 Standard Drawers NOTICE Checking Drawer Alignment The unit’s drawers are aligned at the factory before shipment. However, their alignment could have been disturbed during shipment or during overlay panel installation. Check each drawer to confirm that it is aligned: Drawer adjustments are made by moving the slide that carries the drawer’s rail. Minor adjustments may be made by loosening one of the slide’s mounting screws, adjusting the slide and retightening the screw.
Minor Adjustment: Minor Adjustment: Screws Should Be Loose Note: The mounting holes on the slide are slightly larger than the screws’ diameter. Note: The mounting holes on the slide are slightly larger than the screws’ diameter. 1. Loosen one slide’s mounting screws. 1. Loosen one slide’s mounting screws. 2. Push the slide upward or downward to match the position of the other slide. 2. Level the slide. 3. Retighten the screws. Mounting Screws Level the Slide 3. Retighten the screws. 4.
Full Overlay Drawer Panel 7 Drawer Panel Installation Drawer Panel Preparation Custom 1/4" Drawer Panel Inserts A full overlay drawer panel completely covers the drawer frame and handle to give you a built-in appearance. Drawer Panel Preparation Custom drawer panels can be inserted into the drawer fronts. Custom drawer panels can be flat or raised, as long as the maximum panel thickness where inserted into the drawer front reveal (channel) is 1/4"-thick.
Removing Existing Drawer Fronts Panel Installation 1. Open drawer. Pull drawer gasket out of groove (top edge of drawer only). Start in the middle and pull outward, moving toward the edge. This may take some force. 1. Place prepared panel against drawer front and secure with clamps. 2. Be certain the panel is aligned flush with the top of the drawer handle. 2. Remove the two screws located at the ends of the handle. Remove the handle. 3.
Hook and Loop Fastener Mount 8 Wood Grille Overlay Grille Overlay Your model’s grille is designed to accept a wood grille overlay. An overlay may be used to complement a door overlay and provides a seamless look for your surrounding decor. Follow the instructions below to prepare and install your grille overlay. Be sure to read over this chapter completely before beginning. Preparation You may also mount your overlay to your grille using hook and loop type fasteners.
1/4 1/2 3-3/32 2-1/8 11/64 u-line.
9 Prepare Plumbing 10 Level the Unit Leveling Information ! CAUTION Plumbing installation must observe all state and local codes. All water and drain connections MUST BE made by a licensed/qualified plumbing contractor. Failure to follow recommendations and instructions may result in damage and/or harm. Water Supply Connection When connecting the water supply, follow these guidelines: Note: It is recommended that the unit is level. 1.
2. Insert the screws through the anti-tip bracket (B) and attach the bracket to the unit. Tighten screws securely. 11 Install Unit 3. Repeat for the other side. 1. Plug in the power cord. 2. Open the top drawer and press the POWER icon to turn the unit OFF. Note: The bracket should be flush with the surface it is being attached to. If it is not, loosen the screws and slide the bracket against the mounting surface. Tighten screws securely. 3.
First Time Start-Up All U-line units are shipped from the factory with controls that are preset. No initial adjustments are required. Once installation and leveling is complete, the unit is ready for initial start-up and operation. Open the top drawer press and hold the POWER icon on the display panel for approximately ten seconds until the °F symbol flashes and release. U-Line recommends that the unit be allowed to run overnight prior to loading the refrigerator with product.
INSTALLATION GUIDE ® PRODUCT INFORMATION Complete Installation Guides, Use and Care Guides, Specifications & Features and Benefits, CAD Drawings, Overlay Panel/Frame and Toe-Kick Specifications and Instructions, Compliance Documentation and Applicable Energy Guides are available for reference and download at u-line.com. SERVICE INFORMATION Please consult your Use and Care Guide for troubleshooting information. Answers to Customer Frequently Asked Questions are available at u-line.
