Mid-Gain Advanced RF Isolation Variable Beamwidth Antenna Model: AM-V2G-Ti
Introduction Thank you for purchasing the Ubiquiti Networks™ airMAX™ Titanium Sector. This Quick Start Guide is designed to guide you through the installation of the antenna. This Quick Start Guide also includes the warranty terms and is for use with the airMAX Sector Antenna, model AM-V2G-Ti. Package Contents Antenna Protective Shroud U-Brackets (Qty. 2) Pole Brackets (Qty. 2) Pole Clamps (Qty.
Installation Requirements • Rocket™M2 Titanium or RocketM2 (sold separately) • 12 mm and 13 mm wrenches • Shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the PoE. We recommend that you protect your networks from the most brutal environments and devastating ESD attacks with industrial‑grade shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.
Hardware Installation 1. Set the desired beamwidth by adjusting the Beamwidth Deflectors. Loosen the four hex head screws enough to move the Beamwidth Deflectors, but do not remove the screws. 2. Carefully move the Beamwidth Deflectors to the desired angle, as indicated by the screw slots. 120° Beamwidth 90° Beamwidth 60° Beamwidth Important: Both deflectors must be set to the same angle. 3. Tighten the four hex head screws.
4. Attach the RF Cables to the connectors labeled Chain 0 and Chain 1 on the RocketM. 5. Attach the RocketM to the Rocket Mounting Bracket. a. Align the mounting tabs on the back of the RocketM with the four mounting slots on the bracket. b. Slide the RocketM down until it locks into place.
. Connect the other ends of the RF Cables to the RF Connectors on the antenna. 7. Slide the Protective Shroud down over the RocketM until it locks onto the Rocket Mounting Bracket. Note: If you have trouble locking the shroud into place, try adjusting the placement of the RF Cables.
8. Attach the U-Brackets to the antenna: a. Secure the slotted U-Bracket to the upper Mounting Lugs of the antenna using two Serrated Flange Nuts. b. Secure the other U-Bracket to the lower Mounting Lugs of the antenna using two Serrated Flange Nuts. Note: Orient both U-Brackets as shown below.
9. Insert two Carriage Bolts into each Pole Bracket. 10. Attach each Pole Bracket to each U-Bracket using two Serrated Flange Bolts. Hand-tighten only.
11. To mount the antenna to the pole, slide a Pole Clamp over each pair of Carriage Bolts. Secure each Pole Clamp with two Serrated Flange Nuts. Note: The mounting assembly can accommodate a Ø 1.5" - 3.0" pole.
12. The antenna has an electrical downtilt of 4°. To further adjust the elevation angle: a. Loosen the four Serrated Flange Bolts on the U-Brackets and the two Serrated Flange Nuts on the upper Pole Clamp. b. Slide the antenna to the desired tilt. (The brackets may slide along the pole, depending on the angle of the elevation tilt.) c. Tighten all bolts and nuts to approximately 25 N-m (18 lb-ft) or less to avoid deforming the pole.
Specifications AM-V2G-Ti Dimensions Weight Frequency Range 773 x 372 x 120 mm 6.40 kg (with Brackets) 2.3-2.6 GHz Beamwidth Angles 60°/ 90°/ 120° Gain (Beamwidth Dependent) 17 dBi @ 60° 16 dBi @ 90° 15 dBi @ 120° Electrical Downtilt 4° Wind Survivability 125 mph Wind Loading Polarization 144 lbf @ 125 mph Dual Linear Cross-Pol Isolation 25 dB Typical F/B Ratio 30 dB Typical Max. VSWR RF Connectors Compatible Radios Mounting ETSI Specification Certifications 1.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label.
Limited Warranty UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation.
Disclaimer EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PUR
Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you.
RoHS/WEEE Compliance Statement English European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities.
Español La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity Česky [Czech] UBIQUITI NETWORKS tímto prohla uje, e tento UBIQUITI NETWORKS device, je ve shod se základními po adavky a dal ími p íslu n mi ustanoveními sm rnice 1999/5/ES. Dansk [Danish] Undertegnede UBIQUITI NETWORKS erklærer herved, at følgende udstyr UBIQUITI NETWORKS device, overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Italiano [Italian] Con la presente UBIQUITI NETWORKS dichiara che questo UBIQUITI NETWORKS device, è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device, atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem.
www.ubnt.com © 2012-2013 Ubiquiti Networks, Inc. All rights reserved.