720p Indoor IP Camera with Infrared Model: UVC-Dome
Introduction Thank you for purchasing the Ubiquiti Networks™ UniFi® Video Camera Dome. This Quick Start Guide is designed to guide you through the installation of the camera and show you how to access the Camera Configuration Interface. This Quick Start Guide also includes the warranty terms. The UniFi Video software and User Guide are available for download at downloads.ubnt.
Hardware Overview Flange Nut Mounting Sleeve Alignment Notch Camera Body Microphone Focus Ring Wide Angle Lens
Power LED Reset Button Video Camera Reset Ethernet Port Ethernet LED microSD Slot M/N: UVC-Dome 24V 0.5A POE LEDs Ethernet The Ethernet LED will light steady green when an active Ethernet connection is made and flash when there is activity. Power The Power LED will light steady amber when the camera is connected to a power source. Note: LED operation may be disabled using the Camera Configuration Interface.
Installation 1. Cut a 70 mm (2.75") diameter mounting hole in the ceiling tile: a. Remove a ceiling tile. b. Remove the adhesive Mounting Template from the backing and adhere it to the center of the tile. c. Cut the hole along the Mounting Template. 2. Press down and rotate the Mounting Sleeve until the Alignment Notch lines up with the alignment arrow on the camera bezel. Detach the Mounting Sleeve from the Camera Body. Reset Video Camera M/N: UVC-Dome 0.
3. Insert the Mounting Sleeve into the ceiling tile and securely attach the Flange Nut. 4. Feed an Ethernet cable through the Mounting Sleeve.
5. (Optional) Insert a microSD card into the microSD Slot until it locks into the slot. Reset Video Camera M/N: UVC-Dome 24V 0.5A POE 6. Connect the Ethernet cable to the Ethernet port. Reset Video Camera M/N: UVC-Dome 24V 0.
7. Line up the alignment arrow on the camera bezel with the Alignment Notch on the Mounting Sleeve. 8. Insert the Camera Body into the Mounting Sleeve. 9. Rotate the Camera Body to lock it into the Mounting Sleeve.
10. Set the ceiling tile back into place. 11. Remove the protective cover from the camera lens. 12. Aim the camera in the desired direction.
Connecting Power over Ethernet 1. Connect the other end of the Ethernet cable to one of the following: • PoE Adapter Connect the UniFi Video Camera Dome to the Ethernet port labeled POE on the included PoE Adapter. • EdgeSwitch (shown below) or TOUGHSwitch Connect the UniFi Video Camera Dome to a port with 24V power enabled and skip steps 2 and 3. 2. Connect an Ethernet cable from your LAN to the Ethernet port labeled LAN on the PoE Adapter.
3. Connect the Power Cord to the power port on the PoE Adapter. Connect the other end of the Power Cord to a power outlet. UniFi Video The UniFI Video software is pre-installed on the UniFi NVR (sold separately). If you do not have the UniFi NVR, you can download and install the latest version of the UniFi Video software at downloads.ubnt.com/unifivideo; the UniFi Video auto-management feature should automatically detect and install your new camera(s).
Camera Configuration Interface If you have not yet installed UniFi Video, or if you plan to use the camera as a stand-alone camera, you can access the Camera Configuration Interface via a web browser. 1. Ensure that your host machine is connected to the same LAN as the camera. 2. The camera is set to DHCP by default. If you have a router or DHCP server providing addresses on your network, please check your DHCP Client Table or download the Ubiquiti Discovery Tool from: http://www.ubnt.
5. The Main screen will appear and you should see a live video stream from the camera. Note: If you need to change the camera network settings (DHCP/Static), go to Network Settings on the Device tab.
Specifications UniFi Video Camera Dome Dimensions 111 x 96 x 96 mm (4.4 x 3.8 x 3.8") Weight 178 g (6.28 oz.) Ports (1) 10/100 Ethernet Port Sensor ¼" CMOS Image Sensor Lens f=1.96 mm/ F2.0 Power LED Amber Link/Activity LED Night Mode Green IR LED with Mechanical IR Cut Filter Microphone Power Method Yes Passive Power over Ethernet (12-24V) Power Supply 24V, 0.5A PoE Adapter (Included) Max.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1.
Limited Warranty UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation.
Disclaimer EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PUR
Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you.
Industry Canada This Class A digital apparatus complies with Canadian CAN ICES-3(B). To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2.
RoHS/WEEE Compliance Statement English European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities.
Español La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity Česky [Czech] UBIQUITI NETWORKS tímto prohla uje, e tento UBIQUITI NETWORKS device, je ve shod se základními po adavky a dal ími p íslu n mi ustanoveními sm rnice 1999/5/ES. Dansk [Danish] Undertegnede UBIQUITI NETWORKS erklærer herved, at følgende udstyr UBIQUITI NETWORKS device, overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Latviski [Latvian] Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device, atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem. Lietuviškai [Lithuanian] UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI NETWORKS įrenginys atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
www.ubnt.com ©2013-2014 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, TOUGHCable, TOUGHSwitch, and UniFi are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. All other trademarks are the property of their respective owners.
