Instructions / Assembly

Issued/Revised: 09/18/13
5FT BEANSTALK CLIMBER -WIDE- 02-07-5060
uPLAY TODAY
800.458.5872
www.ultraplay.com
1
Parts List
PART NUMBER
QTYDESCRIPTION
02-07-01651
5FT BEANSTALK CLIMBER
02-07-01631ENTRY ARCHWAY WIDE w/SOCKET
02-07-02031
EXTENSION PIPE
02-07-00461FOOTER PLATE
33-12-10341
33-11-0103*
6
M8 x 25mm (1") BHCS BOLT
33-11-0301*
2
M8 LOCKWASHER
33-11-0500*
4
M8 LOCK NUT
33-11-0002*1
M10 x 20mm (3/4") BHCS BOLT
33-11-0003*
2
M10 x 25mm (1") BHCS BOLT
33-11-0005*2M10 x 35mm (1 3/8") BHCS BOLT
33-11-0200*
5
M10 FLATWASHER
33-11-0400*4M10 LOCK NUT
33-11-0203*
1
M12 LOCKWASHER
33-11-0700*2CLAMP RIVET
HARDWARE COMPLETE
Items listed below Hardware Complete line are included with Hardware Complete Number
Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store
Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any
Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Any bolt end
protruding more than two full threads beyond the face of the nut causes risk of clothing entanglement.
Promptly cut-off flush, file smooth, and treat to prevent corrosion.
Unless Otherwise Specified, All Units of Measure are Each
Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete.
Note: Loctite (supplied by others) should be used on any non-patch hardware.
INSTALLATION INSTRUCTIONS:
IMPORTANT:
DETERMINE WHICH MOUNTING OPTION YOU ARE USING; SURFACE MOUNT, ONGROUND, OR IN-GROUND.
1. Choose the appropriate Decks to receive Beanstalk Climber.
2. Trim out all slots in Deck with utility knife if necessary.
3. Attach Tube Clamps to Entry Archway Wide w/Socket. Secure using M8 x 25mm B.H.C.S. Bolt and M8 Lock Washer. See Detail 029.
4. Attach Tube Clamps to Uprights using M8 x 25mm B.H.C.S. Bolt and M8 Lock Nut. See Detail 030. (Do not install Clamp Rivet
until entire unit is assembled.)
5. Attach bottom of Entry Archway Wide w/Socket to Deck using M10 x 25mm B.H.C.S. Bolt, M10 Flat Washer, and M10 Lock Nut. See
Detail 050.
6. Insert top of Beanstalk Climber into socket of Entry Archway and attach using M10 x 20mm B.H.C.S Bolt, M12 Lock Washer, and
M10 Flat Washer. See Detail 071.
7. Attach Extension Tube to Footer Plate using M10 x 35mm B.H.C.S. Bolt and M10 Lock Nut. See Detail 036.
8. Insert Extension Tube into socket of the Beanstalk Climber and secure with M10 x 35mm B.H.C.S. Bolt and M10 Lock Nut. See
Detail 077.
9. Plumb and level entire assembly before tightening all fasteners. Note: Apply Loctite to threads of Bolt to prevent from loosening.