User manual

Congratulaons on your new PARK MINI. With PARK MINI in
your car, you don’t need to remember to set the parking disc,
thus avoiding expensive parking ckets.
The electronics in PARK MINI register the movement of the
car and PARK MINI automacally sets the clock at the correct
parking me, and releases the parking mode only once the car
starts moving again.
Before making use of PARK MINI, it is recommended to care-
fully read the complete user manual.
To ensure correct installaon of your
PARK MINI, please follow
the instrucons below:
Prior to installaon
A: Acvate the baery
Gently remove the plasc strip and push the baery back
into place if it comes loose. Should the baery by accident
fall out, reinsert it with the + facing upwards (same side as
the one with text). If the baery are placed correctly, “hours”
ash in the display.
B: Set the digital clock
(The digital clock automacally sets both summer and winter
me, but can be de acvated manually if necessary, see C:)
1. Acvate setup mode by pushing buon
❶ with a
pointy object (e.g. pencil) unl the ”hours”- digits start
ashing.
2. When “hours” ashes in the display, push buon
❷
repeatedly unl the hours are set correctly.
Please note that only one parking disc is allowed in your car at
any me, and it is the owner’s responsibility to install
PARK
MINI
correctly.
Needit ApS and Needit Denmark ApS do not reimburse any
parking ckets.
Mounng af PARK MINI
1. Find the best place on the inside of the windscreen’s lower
Seng the parking me manually
PARK MINI can also be manually set, as required by law.
BEK nr. 327 of 29/04/2003 (§3 stk. 3): “If, during the vehicle’s
parking, a period of no me limit occurs, the clock must be set
no later than the end of the non-limited me period, at the cor-
rect me, from when a new me limited period begins.”
If you need to set the PARK MINI manually, just push buon
❷ and the clock will start running at 30 minutes intervals. Run
the clock to the correct me and release. Please note that this
funcon is only available when PARK MINI is in parking mode.
Service and warranty
At our website www.parkmini.de you will nd an FAQ secon
with informaon on your new PARK MINI. Advice is also availa-
ble from [e-mail]
Needit ApS and Needit Denmark ApS provide a warranty accord-
ing to the Danish Sale of Goods Act. If faults and imperfecons
occur during the warranty period, please return the device
directly to your retailer, and it will be repaired or replaced with
a new PARK MINI.
With the CE label, the manufacturer of the product guarantees
that the product is produced according to the standard Europe-
an safety, health and environmental standards.
The declaraon of conformity conrms that the product in
queson is in accordance with (CE) EN 55022 (Radio disturbance
characteriscs) and (CE) EN 55024 (Standards for Commercial
Electronic Products).
WEEE
PARK MINI is not to be disposed of with general household
waste, but has to be disposed of separately. The baery may
be returned to any retailer selling baeries, and the PARK
MINI itself may be disposed of at your local recycling staon or
by the retailer.
Specicaons
Size (cenmeters): 8.3 x 4.5 x 2.5
Baery Coin cell no.: Coin Baery no. CR 2450 - 3 Volt
Baery life expectancy: Approximately 2 years
Clock accuracy (average): ± 2 minutes/2 years
Reacon me (parking mode): Approximately 20 sec.
Terminaon of parking mode: Approximately 20 sec.
PARK MINI is patent pending.
All rights to PARK MINI belong to:
Needit Deutschland GmbH • Allee der Kosmonauten 32 B
12681 Berlin • Deutschland
Phone: [phone]
E-mail: [e-mail]
Website: www.parkmini.de
Please note that the content of this user manual
is subject to change.
Please enclose a copy of your receipt, as it is also your warranty.
Do not try to open PARK MINI by force, as the electronics will
be destroyed and the warranty be void.
IMPORTANT
It is the responsibility of the driver to set the clock correctly. Any
parking cket or installaon mistake is not the responsibility of
Needit ApS or Needit Denmark ApS.
Maintenance
Avoid exposing PARK MINI to extreme temperatures (below -20
°C or above +75 °C), as it may destroy the electronics and/or
aect the reacon me.
If PARK MINI is exposed to heavy moisture or water, please use
a clean cloth to dry it.
Use only a cloth to clean the device. Do not use any cleansing
agents on the device.
Approvals and cercates
PARK MINI has been approved by the Danish Transport Author-
ity with reference to the execuve order no. 327, 2003 concern-
ing parking discs. Tested by SGS-TÜV Saar GmbH.
CE labelling
With the CE label, Needit ApS and Needit Denmark ApS declares
that the product fullls the general safety requirements in the
relevant CE labeling direcves.
Baery
When the diode ❶ starts ashing for 10 seconds when PARK
MINI enters or exits parking mode, it indicates that the baery
should be changed within a week.
Replacement baeries are available at retailers selling coin
baeries.
REMEMBER TO RESET THE CLOCK.
When the baery is changed, the clock will reset automacally.
All me informaon can always be reset by following the setup
instrucons.
Please note that the LCD display of
PARK MINI will switch o
shortly aer the baery is removed, so please avoid leaving
your car parked anywhere with the baery removed.
Changing the baery
1. Buy a new coin baery no. CR 2450 – 3 Volt.
2. Gently pull out the baery holder all the way.
3. Remove old baery.
4. Insert new baery. Remember to wipe the baery.
5. Gently push the baery holder all the way in.
3. Push buon
❶ once and ”minutes” ash in the display.
Set the minutes by pushing buon ❷.
4. Set year, month and date as above (in that order).
Once you have set the above details, no digits in the display
should be ashing (please note that the colon (:) between hours
and minutes will ash at all mes).
Please push buon ❶ repeatedly to stop any ashing in the dis-
play. If you have made a mistake in the setup, reset PARK MINI
right corner (legal requirement) where both pads touch
the glass. Make sure you have access to all the buons
and are able to change the baery.
2. Wipe the inside of the windscreen with a damp cloth
and a lile detergent. Dry the windscreen and use the
enclosed cleaning ssue to clean the chosen spot very
carefully. Dry it with a so clean cloth. (Only the enclosed
cleaning ssue should be used - no other cleansing agent).
3. Make sure the windscreen is no less that +15 degrees
Celsius, as the pads do not work opmally at less than 15
degrees. Use either the fan in the car or, with cauon, a
hair dryer to heatup the windscreen.
4. Remove the protecve foil from the 2 pads and press the
device rmly to the windscreen for about 30 seconds
Press at the middle of the backside. Check from outside if
all the pads are indeed aached to the windscreen.
5. You have now mounted your
PARK MINI and are ready to go.
NB!
PARK MINI has to be mounted on the windscreen for it to work
correctly.
How does PARK MINI work?
When parking your car, PARK MINI will automacally set the
clock forward to the next half hour aer your arrival me. (E.g.
arrival at 10:07, PARK MINI sets the me at 10:30).
by pushing buon
❶ unl the ”hours”- digits start ashing.
We recommend checking the seng of the clock regularly,
especially on the change between summer me/winter me
and back again.
C: Acvate/deacvate summer me/winter me
The digital clock automacally sets both summer and winter
me by default. But if used in a territory without, you can deac-
vate, using the following steps.
1. Acvate setup mode by push ing both buon
❶ and buon
❷ unl the ”hours” and ”minutes”- digits show ”oN:Su”.
2. Gently release pressure on buon ❶.
3. Hold the buon ❷ unl the display reads ”oF:Su”.
4. Display will automacally return to funcon mode.
Your PARK MINI is now ready to be mounted on the inside of
your windscreen.
PARK MINI
electronic parking disc
User manual
DE, EN v. 003
Button ❶
and diode
Button
❷
Battery