TDS

TECHNICAL DATA SHEETTECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, tness for a particular purpose or of any other nature are
made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative, call 1-800-854-0133 Ext. 2
(U.S.A. only) or visit behr.com. ©2020 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 2/2020
PORCH & PATIO ANTI-SLIP FLOOR PAINT
NO. 6250 (TEXTURED LOW-LUSTRE) ULTRA PURE WHITE
®
1 of 2
PRODUCT INFORMATION
BEHR PREMIUM® Porch & Patio Anti-Slip Floor Paint is a 100% acrylic textured low-lustre enamel that is ideal for interior/exterior
applications on wood and concrete porches, patios, pool decks and walkways. It provides a mildew resistant paint nish that
resists cracking and peeling, as well as withstands scung and fading.
RECOMMENDED USES:
This product is ideal for porches, oors, decks, basements, patios, siding, trim, furniture and trellises. Not for use on garage
oors or areas subject to automotive trac. Use on previously painted or primed interior or exterior surfaces such as:
• Wood • Concrete • Composite Wood
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 6250 Ultra Pure White® 128  oz / 2  oz
No. 6230 Deep Base 116  oz / 14  oz
PRE-MIXED COLORS:
No. 6295 Slate Gray
Gloss: 0-5 @ 60°
Sheen: 0-5 @ 85°
Resin Type: 100% Acrylic
Weight per Gallon: 12.5 lb
% Solids by Volume: 48% ± 2%
% Solids by Weight: 64% ± 2%
VOC: <50 g/L
Flash Point: N/A
Viscosity: 120-130 KU
Recommended Film Thickness:
Wet: 21.3 Dry: 10.2 mils @ 75 sq ft/gal
Wet: 10.7 Dry: 5.1 mils @ 150 sq ft/gal
Coverage: 75-150 sq ft/gal depending on application
method and substrate porosity. Does not include the loss of
material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller: 1/4" - 3/8" nap roller, depending on surface texture
Spray: Texture sprayer capable of 1 gpm with a 3 mm tip.
Do not use with airless sprayer.
Thinning: Do not thin if using a roller or brush; however, if
using a sprayer and thinning is required, thin with water at a
rate of no more than 1/2 pint per gallon.
Dry Time: @77°F & 50% RH
To Touch: 2 hours
To Recoat: 2-4 hours
Dry times are temperature, humidity, and lm thickness
dependent.
SURFACE PREPARATION:
New or Weathered Wood: Use a product such as BEHR
PREMIUM® No. 63 All-In-One Wood Cleaner. Lightly sand to
remove remaining wood bers/fuzz.
Note: WARNING! Sanding or scraping pressure treated
lumber may be hazardous; wear appropriate protection.
Painted Surfaces-Wood: For a painted surface in sound
condition, use a product to clean and prepare the surface.
If the coating is failing or peeling, use a paint stripper to
remove old coating. Scu sand glossy surfaces. Use stainless
steel or galvanized nails to prevent nail staining. Countersink
nail heads, repair imperfections and sand smooth. Remove
all dust with a damp cloth, allow to dry.
Uncoated Concrete or Masonry Surfaces: Allow new
surfaces to cure 30 days. Clean and etch surface using a
product such as a muriatic acid etcher (read and follow all
manufacturer’s label directions) to achieve a textured prole
similar to 150 grit sandpaper. Wipe your ngers over the
clean, dry oor to check for dust or powder. Ensure there
is no residue on your ngers that may have been left from
the etcher. If residue is found, rinse the surface to remove
residue. Allow the surface to dry completely. Sprinkle a few
drops of water onto the surface. If water is quickly absorbed
and the surface feels like 150 grit sandpaper, the surface is
ready. If not, re-etch.
Painted Surfaces-Concrete: For a painted surface in
sound condition, use a product to clean and prepare the
surface. If the coating is failing or peeling, use a paint
stripper to remove old coating or scrape/sand down to a
sound concrete surface. Scu sand glossy surfaces. Clean
and spot etch any exposed concrete. Remove all dust with a
damp cloth, allow to dry.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, nd out how to
protect yourself and your family by contacting the National
Lead Information Center at 1-800-424-LEAD or log on to
ww.epa.gov/lead.
SYSTEM RECOMMENDATIONS:
Wood:
• 1 coat BEHR Kitchen, Bath & Trim Interior All-In-One Primer
& Sealer No. 75 (interior only) or BEHR Multi-Surface
Interior/ Exterior Stain-Blocking Primer & Sealer No. 436
2 coats BEHR PREMIUM Porch & Patio Anti-Slip Floor Paint
Concrete & Masonry:
• 1 coat BEHR PREMIUM Concrete & Masonry Bonding Primer
No. 880
2 coats BEHR PREMIUM Porch & Patio Anti-Slip Floor Paint
CLEANUP/DISPOSAL:
Clean all tools and equipment with clean water. Properly
dispose of all soiled rags. For disposal of empty containers
and unused product, contact your household refuse
collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• Do not use on areas subject to automotive tires or
hydrostatic pressure.
• Painted surfaves may become slippery when wet.
• Do not use on roofs.
COMPLIES WITH THE BELOW AS OF 2/1/2020
SCAQMD YES OTC YES
CARB SCM 2007 YES LADCO YES
OTC PHASE ll YES AIM YES