Use and Care Manual
Table Of Contents
- ProShop II™ 10-inch Table Saw
- 1.0 IMPORTANT SAFETY INSTRUCTIONS
- 2.0 Table of contents
- 3.0 About this manual
- 4.0 Table Saw terminology
- 5.0 Specifications
- 6.0 Setup and assembly
- 6.1 Shipping contents
- 6.2 Tools required for assembly
- 6.3 Unpacking and cleanup
- 6.4 Installing legs and levelers
- 6.5 Extension wings
- 6.6 Handwheels
- 6.7 Motor cover
- 6.8 Rails and fence
- 6.9 Wood extension table
- 6.10 Switch bracket
- 6.11 Dust collection
- 6.12 Riving knife
- 6.13 Anti-kickback pawls
- 6.14 Blade guard
- 6.15 Blade installation/replacement
- 6.16 Low profile riving knife
- 6.17 Table insert
- 6.18 Miter gauge
- 6.19 Tool storage
- 7.0 Electrical connections
- 8.0 Adjustments
- 9.0 Operations
- 10.0 Safety devices
- 11.0 User-maintenance
- 12.0 Optional accessories
- 13.0 Troubleshooting JPS2 ProShop II
- 14.0 Replacement Parts
- 14.1.1 Motor and Trunnion – Exploded View
- 14.1.2 Motor and Trunnion – Parts List
- 14.2.1 Table and Cabinet– Exploded View
- 14.2.2 Table and Cabinet– Parts List
- 14.3.1 Stand Assembly – Exploded View
- 14.3.2 Stand Assembly – Parts List
- 14.4.1 Switch Assembly – Exploded View
- 14.4.2 Switch Assembly – Parts List
- 14.5.1 Blade Guard Assembly – Exploded View
- 14.5.2 Blade Guard Assembly – Parts List
- 14.6.1 Miter Gauge Assembly – Exploded View
- 14.6.2 Miter Gauge Assembly – Parts List
- 15.0 Electrical Connections for JPS2
- 16.0 Warranty and Service
10
Dust collection
Dust port outside diameter 4 in. (102 mm)
Recommended minimum extraction volume 400 CFM (0.5 CMM)
General Dimensions
Base footprint 23-1/2 x 24-1/2 in. (597 x 623 mm)
Assembled, with 30-in. rail set, L x W x H 60 x 40 x 43 in. (1524 x 1016 x 1090 mm)
Assembled, with 52-in. rail set, L x W x H 82 x 40 x 43 in. (2083 x 1016 x 1090 mm)
Shipping dimensions, saw only, L x W x H 30 x 29-3/4 x 29 in. (76 x 75.5 x 74.5 cm)
Weights
Saw only without wings – net weight 178 lbs (81 kg)
Saw only without wings – shipping weight 191.5 lbs (87 kg)
1
subject to local/national electrical codes.
2
The specified values are emission levels and are not necessarily to be seen as safe operating levels. As workplace
conditions vary, this information is intended to allow the user to make a better estimation of the hazards and risks
involved only.
L = length, W = width, H = height, D = depth
n/a = not applicable
The specifications in this manual were current at time of publication, but because of our policy of continuous
improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring
obligations.
5.1 Kit configurations
Stock numbers
120V model 230V model
Proshop II saw only
725000 725001
Proshop II saw, 30” rip, cast wings 725000K 725002K
Proshop II saw, 30” rip, steel wings
725004K 725006K
Proshop II saw, 52” rip, cast wings, wood extension table
725001K 725003K
Proshop II saw, 52” rip, steel wings, wood extension table
725005K 725007K
Table 2