Use and Care Manual
Table Of Contents
- ProShop II™ 10-inch Table Saw
- 1.0 IMPORTANT SAFETY INSTRUCTIONS
- 2.0 Table of contents
- 3.0 About this manual
- 4.0 Table Saw terminology
- 5.0 Specifications
- 6.0 Setup and assembly
- 6.1 Shipping contents
- 6.2 Tools required for assembly
- 6.3 Unpacking and cleanup
- 6.4 Installing legs and levelers
- 6.5 Extension wings
- 6.6 Handwheels
- 6.7 Motor cover
- 6.8 Rails and fence
- 6.9 Wood extension table
- 6.10 Switch bracket
- 6.11 Dust collection
- 6.12 Riving knife
- 6.13 Anti-kickback pawls
- 6.14 Blade guard
- 6.15 Blade installation/replacement
- 6.16 Low profile riving knife
- 6.17 Table insert
- 6.18 Miter gauge
- 6.19 Tool storage
- 7.0 Electrical connections
- 8.0 Adjustments
- 9.0 Operations
- 10.0 Safety devices
- 11.0 User-maintenance
- 12.0 Optional accessories
- 13.0 Troubleshooting JPS2 ProShop II
- 14.0 Replacement Parts
- 14.1.1 Motor and Trunnion – Exploded View
- 14.1.2 Motor and Trunnion – Parts List
- 14.2.1 Table and Cabinet– Exploded View
- 14.2.2 Table and Cabinet– Parts List
- 14.3.1 Stand Assembly – Exploded View
- 14.3.2 Stand Assembly – Parts List
- 14.4.1 Switch Assembly – Exploded View
- 14.4.2 Switch Assembly – Parts List
- 14.5.1 Blade Guard Assembly – Exploded View
- 14.5.2 Blade Guard Assembly – Parts List
- 14.6.1 Miter Gauge Assembly – Exploded View
- 14.6.2 Miter Gauge Assembly – Parts List
- 15.0 Electrical Connections for JPS2
- 16.0 Warranty and Service
![](/manual/unbranded/725007k/use-and-care-manual-english/images/img-22.png)
26
11.0 User-maintenance
Always disconnect power to
the machine before performing maintenance.
Failure to do this may result in serious
personal injury.
11.1 Cleaning
Clean the JPS2 according to the schedule below to
ensure maximum performance. The schedule
assumes the saw is being used every day.
Daily:
• Use a brush or compressed air to remove
chips or debris – do not use bare hands.
• Wipe down the table surface and T-slots
with a rust preventive.
• Clean pitch and resin from the saw blade.
Weekly:
• Clean motor housing with compressed air.
• Wipe down fence rails with a dry silicon
lubricant.
11.2 Lubrication
Lubricate the areas indicated below every 12
months.
• Lubricate blade angling trunnions with 6 or 7
drops of light machine oil.
• Lubricate the blade height trunnion with 6 or
7 drops of light machine oil.
• Worm gears and threads should be
lubricated with an automotive wheel bearing
grease.
• Check all adjustments after lubricating.
11.3 Additional servicing
Any additional servicing should be performed by
authorized service personnel.
12.0 Optional accessories
These accessory items, purchased separately, can
enhance the functionality of your table saw.
Contact your dealer to order, or call JET at the
phone number on the cover.
# 725004 – Dado Insert for ProShop II
# 708119 – Universal Mobile Base, adjustable up
to 36” x 36”
# 708158 – Mobile Base Extension Kit (for saws
equipped with wood extension table)