Use and Care Manual
Table Of Contents
- ProShop II™ 10-inch Table Saw
- 1.0 IMPORTANT SAFETY INSTRUCTIONS
- 2.0 Table of contents
- 3.0 About this manual
- 4.0 Table Saw terminology
- 5.0 Specifications
- 6.0 Setup and assembly
- 6.1 Shipping contents
- 6.2 Tools required for assembly
- 6.3 Unpacking and cleanup
- 6.4 Installing legs and levelers
- 6.5 Extension wings
- 6.6 Handwheels
- 6.7 Motor cover
- 6.8 Rails and fence
- 6.9 Wood extension table
- 6.10 Switch bracket
- 6.11 Dust collection
- 6.12 Riving knife
- 6.13 Anti-kickback pawls
- 6.14 Blade guard
- 6.15 Blade installation/replacement
- 6.16 Low profile riving knife
- 6.17 Table insert
- 6.18 Miter gauge
- 6.19 Tool storage
- 7.0 Electrical connections
- 8.0 Adjustments
- 9.0 Operations
- 10.0 Safety devices
- 11.0 User-maintenance
- 12.0 Optional accessories
- 13.0 Troubleshooting JPS2 ProShop II
- 14.0 Replacement Parts
- 14.1.1 Motor and Trunnion – Exploded View
- 14.1.2 Motor and Trunnion – Parts List
- 14.2.1 Table and Cabinet– Exploded View
- 14.2.2 Table and Cabinet– Parts List
- 14.3.1 Stand Assembly – Exploded View
- 14.3.2 Stand Assembly – Parts List
- 14.4.1 Switch Assembly – Exploded View
- 14.4.2 Switch Assembly – Parts List
- 14.5.1 Blade Guard Assembly – Exploded View
- 14.5.2 Blade Guard Assembly – Parts List
- 14.6.1 Miter Gauge Assembly – Exploded View
- 14.6.2 Miter Gauge Assembly – Parts List
- 15.0 Electrical Connections for JPS2
- 16.0 Warranty and Service
27
13.0 Troubleshooting JPS2 ProShop II
Symptom Possible Cause Correction
Motor will not start Low voltage. Check power line for proper voltage.
Open circuit in motor or loose
connection.
Inspect all lead connections on motor for
loose or open connections.
Motor will not start: fuses
or circuit breakers blow.
Short circuit in line cord or plug. Inspect cord or plug for damaged insulation
and shorted wires.
Short circuit in motor or loose
connections.
Inspect all connections on motor for loose or
shorted terminals or worn insulation.
Incorrect fuses or circuit breakers in
power line.
Install correct fuses or circuit breakers.
Motor overheats. Motor overloaded. Reduce load on motor.
Air circulation through the motor
restricted.
Clean motor fan with compressed air to
restore normal air circulation.
Motor stalls, resulting in
blown fuses or tripped
circuit.
Motor overloaded. Reduce load on motor.
Short circuit in motor or loose
connections.
Inspect connections on motor for loose or
shorted terminals or worn insulation.
Low voltage. Correct the low voltage conditions.
Incorrect fuses or circuit breakers in
power line.
Install correct fuses or circuit breakers.
Machine slows when
operating.
Applying too much pressure to
workpiece.
Feed workpiece more slowly.
Belt loose. Tighten belt.
Loud, repetitive noise
coming from machine.
Pulley setscrews or keys are missing
or loose.
Inspect keys and setscrews. Replace or
tighten if necessary.
Motor fan is hitting the cover. Tighten fan or shim cover.
Drive belt is defective. Replace belt.
Blade not square with
miter slot, or fence not
square to blade.
Blade is warped. Replace saw blade.
Table top not parallel to blade. Adjust table parallel to blade.
Fence not parallel to blade. Adjust fence parallel to blade.
Blade does not reach 90
degrees.
90 degree stop is out of adjustment. Adjust 90 degree stop.
Table 4
14.0 Replacement Parts
Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-
800-274-6848 Monday through Friday (see our website for business hours, www.jettools.com). Having the
Model Number and Serial Number of your machine available when you call will allow us to serve you quickly
and accurately.
Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET.
Some parts are shown for reference only, and may not be available individually.