Use and Care Manual
Table Of Contents
- ProShop II™ 10-inch Table Saw
- 1.0 IMPORTANT SAFETY INSTRUCTIONS
- 2.0 Table of contents
- 3.0 About this manual
- 4.0 Table Saw terminology
- 5.0 Specifications
- 6.0 Setup and assembly
- 6.1 Shipping contents
- 6.2 Tools required for assembly
- 6.3 Unpacking and cleanup
- 6.4 Installing legs and levelers
- 6.5 Extension wings
- 6.6 Handwheels
- 6.7 Motor cover
- 6.8 Rails and fence
- 6.9 Wood extension table
- 6.10 Switch bracket
- 6.11 Dust collection
- 6.12 Riving knife
- 6.13 Anti-kickback pawls
- 6.14 Blade guard
- 6.15 Blade installation/replacement
- 6.16 Low profile riving knife
- 6.17 Table insert
- 6.18 Miter gauge
- 6.19 Tool storage
- 7.0 Electrical connections
- 8.0 Adjustments
- 9.0 Operations
- 10.0 Safety devices
- 11.0 User-maintenance
- 12.0 Optional accessories
- 13.0 Troubleshooting JPS2 ProShop II
- 14.0 Replacement Parts
- 14.1.1 Motor and Trunnion – Exploded View
- 14.1.2 Motor and Trunnion – Parts List
- 14.2.1 Table and Cabinet– Exploded View
- 14.2.2 Table and Cabinet– Parts List
- 14.3.1 Stand Assembly – Exploded View
- 14.3.2 Stand Assembly – Parts List
- 14.4.1 Switch Assembly – Exploded View
- 14.4.2 Switch Assembly – Parts List
- 14.5.1 Blade Guard Assembly – Exploded View
- 14.5.2 Blade Guard Assembly – Parts List
- 14.6.1 Miter Gauge Assembly – Exploded View
- 14.6.2 Miter Gauge Assembly – Parts List
- 15.0 Electrical Connections for JPS2
- 16.0 Warranty and Service
9
5.0 Specifications
Table 1
Model number
JPS2-115 JPS2-230
Stock number – saw only
(see Table 2 below for kit configurations)
725000 725001
Motor and Electricals
Motor type Totally enclosed, fan cooled, induction
Horsepower 1.75 HP
Motor phase 1 PH
Motor voltage 120 V 230 V
Cycle 60Hz
Listed FLA (full load amps) 7.4 A 14.8 A
Motor speed 3450 RPM
Starting amps 36 A 18 A
Running amps (no load) 3.7 A 1.8 A
Start capacitor 200MFD 125VAC
Run capacitor
40μF 300VAC
Power transfer belt
On/off switch Magnetic switch KJD17B (NVR type)
Power cord 14AWG x 3, 6 ft (183cm)
Plug provided 5-15P 6-15P
Recommended circuit size
1
15 A
Sound emission without load
2
80 dB at 30 in. (762mm) from blade
Arbor and blade
Arbor diameter 5/8 in. (15.88 mm)
Arbor speed 4000 RPM
Arbor lock included
Arbor wrench included
Blade included 10 in. (254 mm), 40 tooth
Maximum depth of cut at 90 degrees 3-1/8 in. (79 mm)
Maximum depth of cut at 45 degrees 2-1/8 in. (54 mm)
Maximum rip to right of blade 30 in. or 52 in.
Maximum rip to left of blade 13.5 in. (343 mm)
Blade height per one revolution of handwheel 5/32 in. (4 mm) at 90°; 7/64 in. (2.83 mm) at 45°
Dado maximum width 13/16 in. (20.6 mm)
Dado maximum diameter 8 in.
Blade tilt 45° left tilt
Table
Main table dimensions, L x W 20 x 27 in. (508 x 686 mm)
Table dimensions with wings, L x W 44 x 27 in. (1118 x 686 mm)
Table area in front of blade at maximum height 8.81 in. (223.83 mm)
Table height from floor, approximate 34-3/4 in. (883 mm)
Miter T-slot, W x D 3/4 x 3/8 in. (19 x 10 mm)
Edge bevel Front
Main materials
Main table Cast iron
Table insert Aluminum
Extension wings Cast iron or stamped steel
Base and legs Steel
Center trunnion Aluminum
Pulleys Steel