User manual

ManualsBrandsUnbranded ManualsMP3 & MP4 AccessoriesBluetooth speaker Renkforce Aux White

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microﬁlming, or the capture in electronic data

processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent

the technical status at the time of printing.

Pairing

Before transmission between your Bluetooth

device and the speaker is possible,

both devices must be coupled. This process is called “pairing”.

• Turn on the Bluetooth

device which you want to couple with your speaker, and

activate the pairing mode (for more information, see the instruction manual of the

corresponding device). The device will search for Bluetooth

devices within range.

• Turn on the loudspeaker and press the button PAIR for three seconds until a beep

sounds and the LED on the device’s rear panel ﬂashes quickly.

• When the loudspeaker is found, your Bluetooth

device will display the name

“CT-BT1“.

• On your Bluetooth

device select “CT-BT1“. Perhaps you may need to enter the

password “0000” on your Bluetooth

device.

• When pairing is successful, the LED on the rear panel of your device will be continu-

ously blinking.

Only one Bluetooth

device at a time can be coupled to the loudspeaker. If

there is already an active Bluetooth

coupling, then this connection must be

interrupted ﬁrst.

The connection is broken, when the speaker or the Bluetooth

device with

the coupling active is switched off or moved out of range. When the device

is turned back on or when the Bluetooth

device comes back into the range

of the speaker, the connection will be automatically reestablished.

To enable this automatic reconnection, this function may need to be acti-

vated on the Bluetooth

device (please read up your Bluetooth

device’s

instructions regarding this point).

Audio streaming

Audio streaming is the transmission of audio data (music) via Bluetooth

to the speaker.

If you own an A2DP-capable Bluetooth

device, you can connect it with the speaker fol-

lowing the pairing procedure as described above and establish the audio transmission.

• Make sure that both devices are connected via pairing.

• Start playback/audio transmission on your Bluetooth

device (see the correspond-

ing operating manual).

• Now audio transmission is activated.

• Now you can easily control the playback via the controls of your Bluetooth

device.

Wired audio playback

If your audio device does not feature Bluetooth

audio transmission, you may use the

included audio jack to connect to the loudspeaker.

• Connect the connector LINE IN to the audio output of your device’s rear panel

(headphone output) of the audio device.

• Start playback on your audio device.

• Now you can easily control the playback via the controls of your audio device.

Operate as power station

The USB output of the loudspeaker can supply other devices such as mobile phones,

MP3 players, etc. with power.

The USB output can be loaded with max. 2,5 A. Do not connect devices with

a higher current consumption.

•

Connect the device you would like to charge to the USB connector on the rear panel

of the device.

• Switch on the loudspeaker with the toggle ON/OFF switch (set switch to ON position).

• You can load your mobile device onto the enclosed stand while charging.

Maintenance and Cleaning

The BT loudspeaker is maintenance-free.

Only clean it with a slightly moistened cloth. Never use cleaning agents as these can

damage the surface of the casing.

Disposal

Electronic devices are recyclable waste materials and must not be disposed

of in the household waste!

Please dispose of the device at the end of its service life according to the

current statutory requirements.

Technical data

Operating voltage............................... 100-240 V/50/60 Hz

Output power ...................................... 2 x 10 W RMS

USB output .......................................... 5 V/DC / 2.5 A

Bluetooth

Version ............................ V3.0 + EDC

Range ................................................... approx. 10 m

Dimensions.......................................... 395 x 190 x 133 mm

Weight .................................................. approx. 3.3 kg

Declaration of Conformity

We, Conrad Electronic SE, Klaus-Conrad-Straße 1, 92240 Hirschau, hereby declare

that this product adheres to the fundamental requirements and the other relevant

regulations of Directive 1999/5/EC.

The Declaration of Conformity for this product is available at