Use and Care Manual

ManualsBrandsUnbranded ManualsOutdoors6-Piece Acacia Wood TopandSteel Frame Outdoor Dining Set Dining Table with Bench, Chairs with White Cushions

ASSEMBLY INSTRUCTION

PATIO FURNITURE SETS

047613FWF316738; WF316739; W

Summary of content (13 pages)

PAGE 1
ASSEMBLY INSTRUCTION PATIO FURNITURE SETS WF316738; WF316739; WF316740
PAGE 2
X1 B E A E I G X F I D H G X5 X1 P C S T O M N R K J J Q L Note: 1. 50% Tighten before fixing all screws, Allen wrench is recommended instead of an electric drill. 2. Place the item on a flat ground to adjust and make sure it remains stable. 3. Tighten up all screw with tools gradually. 4. If screw are not aligned with holes during assembly, please loosen all the other screws to 50% and continue the assembly process. 5.
PAGE 3
CARTON CONTENT: WF316738 B A x2 D E x1 H G x4 K N x1 x1 x2 F x2 I x2 x2 x4X x2 T O x1 x1 F x5 Hardware WF316739 N C x1 x4 O x4 P x5 R S x5 WF31640 J x2 L x5 M x5 Q x5 x5 Page: 03/12
PAGE 4
Part List & Hardware List: A x2-Table Top B x1-Middle Table Top C x1-Seat Bench D x1-Bottom Table E x2-Side Table Top F x2-Support Table Top G x4-Table Leg I J x2-Bench Leg K x1-Support Bench Leg L x5-Arm Right x2- Support Table Leg M x5-Arm Left N x5-Right Back Leg M6 x 20MM 2 7 x10-Scew Bolt 8 extra (1) x4-Bolt 3 x46 M6 x 45MM extra (3) M6 x 90MM X x2-Support Middle Table Top R x5-Seat Cushion S x5-Back Middle P x5-Back Top Q x5-Seat 1 x38-Bolt O x5-Left Back Leg H x2-Front Ta
PAGE 5
A x2 B x1 E x2 5 x8 8 100% 5 E 5 A B 5 5 5 A E Step 1: Connect Table Top (A) & Middle Table Top (B), Side Table Top (E), tighten Screw Bolt (5) with Allen Key (8). 6 x12 8 6 100% 6 6 6 6 6 6 6 6 6 Step 2: Connect The Part from Step 1, tighten Screw Bolt (6) with Allen Key (8).
PAGE 6
FF x4X2 8 100% 12 X2 X x24 12 12 X 2 12 12 12 12 12 12 12 12 .. 12 12 12 12 X F F X Step 3: Connect The Part from Step 2 & Support Table Top (F), Support Middle Table Top (X), tighten Screw Bolt (6) with Allen Key (8). G x4 1 x12 3 x12 8 80% 1 3 1 3 G G G 1 G 1 1 1 Step 4: Connect The Part from 3 & Table Leg (F), tighten Bolt (1), Flat Washer (3) with Allen Key (8).
PAGE 7
H x2 2 x4 3 x4 2 50% 3 H 2 2 8 2 H 2 Step 5: Connect The Part from Step 4 & Front Table Leg (H), tighten Bolt (2), Flat Washer (3) with Allen Key (8). D x1 1 x4 3 x4 3 50% 1 8 D 1 1 Step 6: Connect The Part from Step 5 & Bottom Table (D), tighten Bolt (1), Flat Washer (3) with Allen Key (8).
PAGE 8
I x2 3 x4 4 x4 3 80% 4 8 I I 3 3 Step 5: Connect The Part from Step 4 & Support Table Leg (I), tighten Screw Bolt (4), Flat Washer (3) with Allen Key (8). 1 x2 3 x2 8 50% 1 3 1 1 Step 6: Connect The Part from Step 5 , tighten Bolt (1), Flat Washer (6) with Allen Key (8).
PAGE 9
100% Step 7: Put the Table upright and make sure all legs are level, then firmly tighten Bolts with Allen Key (8). C x1 J x2 1 x 16 3 x 16 8 50% 1 1 3 3 J J 1 1 1 1 C Step 8: Connect seat Bench (C) & Bench Leg (J), tighten Bolt (1), Flat Washer (3) with Allen Key (8).
PAGE 10
K x1 1 x4 3 x4 3 50% 1 8 K 1 Step 9: Connect The Part from Step 8 & Support Bench Leg (K), tighten Bolt (1), Flat Washer (3) with Allen Key (8). 100% Step 10: Put the Bench upright and make sure all legs are level, then firmly tighten Bolts with Allen Key (8).
PAGE 11
P x1 T x1 N x1 L x1 7 x1 9 x1 P 80% 9 9 N 8 7 T 7 L 8 Step 11: Connect Arm Right (L) & Right Back Leg (N), Back Top (P), Back Bottom (T), tighten Screw Bolt (7),(9) with Allen Key (8). Q x1 10 x1 11 x1 80% 10 11 Q 11 10 8 8 Step 12: Connect The Part from Step 11 & Seat (Q), tighten Screw Bolt (10),(11) with Allen Key (8).
PAGE 12
O x1 9 x1 80% 10 8 10 9 10 x1 S O x1 S 8 9 Step 13: Connect The Part from Step 12 & Left Back Leg (O), Back Middle (S), tighten Screw Bolt (9),(10) with Allen Key (8). M x1 7 x1 8 80% 11 11 x1 7 8 7 11 M Step 14: Connect The Part from Step 13 & Arm Left (M), tighten Screw Bolt (10),(11) with Allen Key (8).
PAGE 13
100% Step 14: Put the Chair upright and make sure all legs are level, then firmly tighten Bolts with Allen Key (8). R x1 R Step 15: Put on Seat Cushion (K) to finish Chair.