Use and Care Manual

6
3
X3. SECTION 4 OF THE CONSUMER PRODUCT SAFETY C OMMISSION’S
OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK
X3.1 Select Protective Surfacing – One of the most important things you can do to reduce the likelihood
of serious head injuries is to install shock-absorbing protective surfacing under and around your play
equipment. The protective surfacing should be applied to a depth that is suitable for the equipment
height in accordance with ASTM Specification F 1292. There are different types of surfacing to choose from;
whichever product you select, follow these guidelines:
X3.1.1 Loose Fill Materials:
X3.1.1.1 Maintain a minimum depth of 9 inches of loose-fill materials such as wood mulch/ chips,
engineered wood fiber (EWF), or shredded/ recycled rubber mulch for equipment up to 8 feet high; and 9
inches of sand or pea gravel for equipment up to 5 feet high. NOTE: An initial fill level of 12 inches will com-
press to about a 9-inch depth of surfacing over time. The surfacing will also compact, displace, and settle,
and should be periodically refilled to maintain at least a 9-inch depth.
X3.1.2 Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If
maintained properly, this should be adequate. (At depths less than 6 inches, the protective material is too
easily displaced or compacted.) NOTE: Do not install home playground equipment over concrete, asphalt,
or any other hard surface. A fall onto a hard surface can result in serious injury to the equipment user.
Grass and dirt are not considered protective surfacing because wear and environmental factors can reduce
their shock absorbing effectiveness. Carpeting and thin mats are generally not adequate protective surfac-
ing. Ground level equipment such as a sandbox, activity wall, playhouse or other equipment that has no
elevated play surface does not need any protective surfacing.
X3.1.3 Use containment, such as digging out around the perimeter and/orv lining the perimeter with
landscape edging. Don’t forget to account for water drainage.
X3.1.3.1 Check and maintain the depth of the loose-fill surfacing material. To maintain the right amount
of loose-fill materials, mark the correct level on play equipment support posts. That way you can easily see
when to replenish and/or redistribute the surfacing.
X3.1.3.2 Do not install loose fill surfacing over hard surfaces such as concrete or asphalt.
X 3.1.4 Poured-in-Place Surfaces or Pre-Manufactured Rubber Tiles You may be interested in using surfacing
other than loose fill materials like rubber tiles or poured-in-place surfaces.
X3.1.4.1 Installations of these surfaces generally require a professional and are not “do-it-yourself ”
projects.
X3.1.4.2 Review surface specifications before purchasing this type of surfacing. Ask the installer/
manufacturer for a report showing that the product has been tested to the following safety standard:
ASTM F1292 Standard Specification for Impact Attenuation of Surfacing Materials within the Use Zone of
Playground Equipment. This report should show the specific height for which the surface is intended to
protect against serious head injury. This height should be equal to or greater than the fall height – the
vertical distance between a designated play surface (elevated surface for standing, sitting, or climbing) and
the protective surfacing below – of your play equipment.
X3.1.4.3 Check the protective surfacing frequently for wear.
X3.1.5 Placement – Proper placement and maintenance of protective surfacing is essential. Be sure to:
X3.1.5.1 Extend surfacing at least 6 feet from the equipment in all directions.
X3.1.5.2 For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal
to twice the height of the top bar from which the swing is suspended.
X3.1.5.3 For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending
chain or rope, plus 6 feet in all directions.
CLEARANCE REQUIREMENTS
Rope
Double
knot
At least 6 feet from trunk
or 1½ times the length of
the swings
rope
8 inch minumum
ground clearance
Figure 2